Vivotek FD9392-EHTV-O User manual

User’s Manual
Qualcomm QCS603 SoC with Built-in AI Engine • Video Processing and Machine Learning •
Supports VCA Solutions via Installation of S&ST APPs •
Network Camera
FD9392-EHTV-O
Driven by
OSSA
Rev. 1.0

VIVOTEK
2 - User's Manual
Table of Contents
Revision History ...............................................................................................................................................4
Read Before Use..............................................................................................................................................4
Symbols and Statements in this Document......................................................................................................4
Package Contents ............................................................................................................................................5
Physical Description ........................................................................................................................................6
Hardware Installation........................................................................................................................................7
Conguration .................................................................................................................................................16
Preview...........................................................................................................................................................24
Peripheral .......................................................................................................................................................24
Zoom / Focus .................................................................................................................................................25
Device Info .....................................................................................................................................................26
Privacy Mask ..................................................................................................................................................27
Virtual Camera ...............................................................................................................................................28
Video settings.................................................................................................................................................28
Stream Conguration .....................................................................................................................................29
Device Health .................................................................................................................................................30
User Management..........................................................................................................................................30
Network ..........................................................................................................................................................31
Date & Time....................................................................................................................................................31
Firmware ........................................................................................................................................................32
Applications - Overview..................................................................................................................................33
Data Magnet and VAST2................................................................................................................................33
Applications - Cloud Connection ....................................................................................................................37
Applications - Legal ........................................................................................................................................42
Technology License Notice.............................................................................................................................43
Electromagnetic Compatibility (EMC).............................................................................................................44

VIVOTEK
User's Manual - 3
Overview
• Powered by Qualcomm QCS603 SoC with a built-in AI Engine
• Powerful Computing for Video Processing and Machine Learning
• Driven by OSSA, running on S&ST OS
• Supports a variety of VCA solutions through S&ST APPs
• Remote Focus Lens / P-iris
• Built-in IR Illuminators up to 50 meters
• Digital input*1, Digital Output*1
• 8MP

VIVOTEK
4 - User's Manual
Read Before Use
The use of surveillance devices may be prohibited by law in your country. The Network Camera
is not only a high-performance web-ready camera but can also be part of a exible surveillance
system. It is the user’s responsibility to ensure that the operation of such devices is legal before
installing this unit for its intended use.
It is important to first verify that all contents received are complete according to the Package
Contents listed below. Take note of the warnings in the Quick Installation Guide before the Network
Camera is installed; then carefully read and follow the instructions in the Installation chapter to
avoid damage due to faulty assembly and installation. This also ensures the product is used
properly as intended.
The Network Camera is a network device and its use should be straightforward for those who
have basic networking knowledge. It is designed for various applications including video sharing,
general security/surveillance, etc. The Configuration chapter suggests ways to best utilize the
Network Camera and ensure proper operations. For creative and professional developers, the URL
Commands of the Network Camera section serves as a helpful reference to customizing existing
homepages or integrating with the current web server.
Symbols and Statements in this Document
i
INFORMATION: provides important messages or advices that might help prevent
inconvenient or problem situations.
NOTE: Notices provide guidance or advices that are related to the functional integrity of
the machine.
Tips: Tips are useful information that helps enhance or facilitae an installation, function,
or process.
WARNING: or IMPORTANT:: These statements indicate situations that can be
dangerous or hazardous to the machine or you.
Electrical Hazard: This statement appears when high voltage electrical hazards might
occur to an operator.
Revision History
■ Rev. 1.0: Initial release.
NOTE:
1. The camera is only to be connected to PoE networks without routing to outside plants.
2. For PoE connection, use only UL listed I.T.E. with PoE output.

VIVOTEK
User's Manual - 5
Package Contents
■ FD9392-EHTV-O
■ T10 stardriver, desiccant bag, screws
■ Waterproof Ethernet and I/O wires cable housing
■ Quick Installation Guide & alignment sticker
■ Side-routing bracket.
WARNING:
1. IR lights emit from ths product.
2. Use appropriate shielding or eye protection.
NOTE:
Use the camera only with a DC power supply that is UL listed, and limited power source
(LPS) certied. The power supply should bear the UL listed and LPS marks. The power
supply should also meet any safety and compliance requirements for the country of use.
REMARQUE :
n’utilisez la caméra qu’avec un bloc d’alimentation CC homologué UL, ainsi qu’avec
une alimentation limitée (LPS) certiée. Le bloc d’alimentation doit porter les indications
d'homologation UL et LPS. Il doit également répondre aux exigences en matière de
sécurité et de conformité relatives au pays d’utilisation.

VIVOTEK
6 - User's Manual
Physical Description
Inner View
I/O routing inlet
Motorized
lens
MicroSD/SDHC/SDXC
Card Slot
IR LEDs
RJ45
Ethernet port
Reset
button
Terminal block
Ethernet
routing inlet
Outer Look
Microphone
Not used
Not used

VIVOTEK
User's Manual - 7
RJ45
Ethernet port
Some of the sufx syntax used in model naming are listed below:
Ew/ heater for extreme weather
Fx Focal length w/ number
T w/ Remote focus lens
R w/ PoE repeater
H w/ High Dynamic Range functionality
NOTE:
Hardware Installation
0002D10766AD
XXXXXX
1
1.Jot down the camera's MAC address for later reference.
IMPORTANT:
The camera comes with an embedded heater and requires an 802.3at PoE switch.
IMPORTANT:
If DC power is preferred, it should comply with: O/P: 12VDC, 1A or 2A min., L.P.S. per IEC
60950-1.
Si l'alimentation CC est préférable, elle devrait être conforme avec ce qui suit : Sortie : 12
VCC, 2 A min., alimentation limitée à conformité CEI 60950-1.
Operating
Temperature
Consumption & Power Input
≥-50ºC PoE: 24.3W (PoE Plus mid-span or switch, 42.5V-57V - 0.57A-0.43A);
AC 24V input: 21.6W [1.76A (PF0.55)];
DC 12V: 21W (1.8A)

VIVOTEK
8 - User's Manual
2.Use the included T10 stardriver to remove the dome
cover.
5~6.3mm
DI/DO: 1.8~2.1mm
3.Loosen and remove the waterproof connectors.
IMPORTANT: You should install the waterproof cable gland to the I/O routing inlet whether
you connect the I/O and power wires or not. If you leave it open, water or moisture can
destroy the camera.
T10

VIVOTEK
User's Manual - 9
4. Insert an Ethernet cable through the cable gland, and the rubber seal.
Ø 5 ~ 6.3mm
approx.
15cm
5. Insert the Ethernet cable through the components of the waterproof connector, e.g., the
rubber seal. Leave 15cm of cable length inside, counting from the edge of the aluminum
hex nut.

VIVOTEK
10 - User's Manual
6. Use a crescent wrench to tighten the components of the waterproof connector. Connect
the cable to the RJ45 connector.
7. If preferred, pass power or I/O wires through the rubber seal and waterproof components
of another connector. Install and tighten the components.

VIVOTEK
User's Manual - 11
8. If applied, connect DI/DO wires, 12/24V DC power, or audio wires to the terminal block.
1
14
# Name
1 AC 24V
2 AC 24V
3 DC 12V IN-
4 DC 12V IN+
5 DI- (GND)
6 GND
7 DI+_0
8 GND
9 DO-_0
10 DO+ (5V)
11 MIC-IN_N (GND)
12 MIC-IN_P
13 AUDIO-OUT_N (GND)
14 AUDIO-OUT_P

VIVOTEK
12 - User's Manual
1. The DO+ pin provides a 12V output, and the max. load is 50mA.
2. The max. voltage for DO- pins is 30VDC (External power).
In order to control AC devices, the following diagram can be taken into consideration.
This diagram uses a relay to control the ON/OFF condition of the AC device.
3. An external relay can be triggered by using the DO+ or by an external power source,
depending on the type of relay you use.
4. In case of using an individual relay (instead of using a relay module), for protection
against voltage or current spikes, a transient voltage suppression diode must be
connected in parallel with the inductive load.
DI-
DO+
DI+
DO-
Switch
External Device
External DC power
Dry contact with external DC power source to supply a relay. Dry contact is the safest connecon
to protect devices.
NC
NO
Relay
Photo
Coupler
DC
DC 0V
DC 0V
External AC power
with Protected Eart
h
AC
PE
PE

VIVOTEK
User's Manual - 13
DI-
DO+
DI+
DO-
Switch
External Device
External DC power
Wet contact with external DC power source to supply a relay.
NC
NO
Relay
DC
External AC power
with Protected Earth
AC
PE
PE
DC 0V
DI-
DO+
DI+
DO-
Switch
External Device
Dry contact and using camera’s DO+ to supply a relay.
NC
NO
Relay
AC
External AC power
with Protected Eart
h
PE
PE

VIVOTEK
14 - User's Manual
- OR -
3/4"
Ø< 35mm
≤3/4”
9. You can either route cables through a routing hole on the ceiling or wall, or you can route
cables through the side of the camera. You can use the side-routing bracket to install a
3/4" conduit. Please note that the conduit hex nut should not be larger than 35mm.

VIVOTEK
User's Manual - 15
When fastening the screws, do not completely tighten the screws. Pass cables through
the routing holes, and then mount the camera by passing the screw heads through the
keyhole slots. Turn the camera counter-clock wise, and then fasten the screws.
10. Attach the included alignment sticker to a preferred location. Drill holes for mounting
screws and if preferred, drill one or two routing holes.

VIVOTEK
16 - User's Manual
Conguration
1. Download the Device Management Tool. The tool can be requested here:
https://devices.securityandsafetythings.com/tooldownload
Make sure DHCP service is available in your local network.
2. Use the Device Management Tool to locate your device.

VIVOTEK
User's Manual - 17
3. You can click Cloud Login to download S&ST apps or visit:
https://store.securityandsafetythings.com/shop/catalog/c/main
4. Enter URL: https://<ip_address>:8443/
Enter admin/admin as the default credential.
Since the connection is using a self-signed certificate, your connection will not be
considered as a secure connection. Click Advanced to proceed.

VIVOTEK
18 - User's Manual
Click Proceed to xxx.xxx.xxx.xxx (Unsafe) to open the web console.
Note the IP addresses below are for reference only.
Enter admin/admin as the default credential.

VIVOTEK
User's Manual - 19
You will be requested to create a new password for security concern. Enter a
combination of alphabetic, numeric, and special characters that is strong enough for
protection.
The new password must comprise of at least 10 characters, containing uppercase,
lowercase, digits or special characters.
1
2
12. On the device web console, click Zooom/Focus. If necessary, zoom in on the scene,
and use the Auto Focus function to nd the best imaging result.

VIVOTEK
20 - User's Manual
14. Carefully tighten the retention screws on the side of the camera lens.
13. With a live view displayed on your laptop, adjust the pan and tilt angles to obtain
an optimal image. Check the live view to ensure the shooting direction and image
coverage.
353°
0°~ 80°