Vivotek IP7142 User manual

EN-1
English
Warning Before Install
Contact your distributor when
such cases happen.
Refer to your user's manual for the
operating temperature.
Power off the Network Camera
as soon as it is found smoking or
smelt unusual.
Do not touch the Network Camera
when it's lightening.
Do not place the Network Camera
on unsteady surfaces.
Do not drop the Network Camera.
Do not insert any object into the
Network Camera, such as needles.

EN-2
Package Contents
1
Software CD
IP7142
Screws
Warranty card
RJ45 female/female coupler Quick installation guide
Camera stand
Sun Shield
Power adapter Silica gel
Silica gel

EN-3
English
Physical Description
2
Connectors
Ethernet 10/100 RJ45 plug
Audio out (green)
Microphone in (pink)
Power cord socket (black)
General I/O terminal block
Earth
Front panel
IR LED
Lens
Reset button
Status LED
Light sensor

EN-4
Hardware Installation
3
1. Open the lens cover.
2. Secure the Network Camera to the wall/ceiling by the supplied camera stand.
12

EN-5
English
Network Deployment
4
POWER C
OLLIS
ION
LINK
R
E
CEIVE
P
ARTITION
12345
1. If you have external devices such as
sensors and alarms, make connections
from general I/O terminal block.
2. Use the supplied RJ45 female/female
coupler to connect the Network Camera
to a switch.
Use Catagory 5 Cross Cable when
Network Camera is directly connected
to PC.
3. Connect the power cable from the
Network Camera to a power outlet.
N.C.
485B
485A
AC24V
AC24V
N.C.: NoConnector
485B: RS485-
485A: RS485+
AC24V: Power in AC 24V
AC24V: Power in AC 24V
G N D : Ground
D I : Digital Input
D O : Digital Output
+12V : Power, 12V DC
GND
DI
DO
+12V
General Connection (without PoE)

EN-6
Power over Ethernet (PoE)
When using a non-PoE switch
Use a PoE power injector (optional) to connect between the Network Camera and
a non-PoE switch.
When using a PoE-enabled switch
The Network Camera is PoE-compliant, allowing transmission of power and data
via single Ethernet cable. See the following illustration to connect the Network
Camera to a PoE-enabled switch via Ethernet cable.
POWER COLLISION
LINK
RECEIVE
PARTITION
12345
non-PoE switch
PoE power injector
(optional)
POWER COLLISIO N
LINK
R
ECEIVE
PARTITION
12345
PoE switch

EN-7
English
1. Install the "Installation Wizard 2" under the Software Utility directory from software CD.
2. The program will conduct analyses on your network environment. After your network is
analyzed, please click on the "Next" button to continue the program.
3. The program will search the VIVOTEK Video Receivers, Video Servers or Network
Cameras on the same LAN.
4. After searching, the main installer window will pop up. Click on the MAC that
matches the one labeled on the side of the camera lens or S/N number on the
label of carton to connect the Internet Explorer to the Network Camera.
0002D17151CD
1
2
Model No.: IP7142
P/N: 100043690G
F/W Ver.: 0100G
CARTON OF NO. 01
MAD E I N TAI WAN
!!0!!
Q 't y: 1 PCS
EAN: 4712123671550
S/N: 0002D17151CD
0002D17151CD
Installation
Wizard 2
IW
2
Assigning IP Address
5

EN-8
For further setup, please refer to user's manual on the software CD.
Ready to Use
6
1. Access to the Network Camera from the Internet.
2. Retrieve live video through web browsers or recording software.
3. Unscrew the zoom controller to adjust the
zoom factor. Upon completion, tighten the
zoom controller.
4. Unscrew the focus controller to adjust the
focus range. Upon completion, tighten the
focus controller.
T
W
∞
N
W
∞
NT

EN-9
English
5. Put the supplied silica gel into the Network Camera and tighten the lens cover. (Please
replace the silica gel with a new one if you open the lens cover after installation.)
Note
If you want to use the supplied sun sheild for outdoor environments, please follow the
steps below to install:
1. Tighten the supplied two screws.
2. Attach the supplied sun shield to the Network Camera and slide it to the desired position.
3. Fix the sun shield with supplied two screws. (Please use different screws for ceiling
mount.)
Silica gel
12
34
Ceiling mountWall mount