ViziT KTM600F User manual

VIZIT-КТМ600F
OPERATING INSTRUCTION
VIZIT-KTM600
KTM600
RF ontroller is intended for access control in auxiliary, industrial and inhabited buildings and
premises and is able to control either electromagnetic or electromechanical lock. ontroller con eader
and ontrol nit and may be used as part of doorphone as well as stand-alone system.
C
, The RF c tains R
CU a
F
RD-4F
M,
Only VIZIT-RF VIZIT-RF keys ( ) are supported3.x or 4.x 13.56 MHz .
ML EL PRG
1S
7S
(1) Power LED
(2) ’sReader antenna
1
2
Destination
Wire colour
Supply voltage for RD-4FRed
GroundBlack
DataWhite
Supply voltage for Reader’s
buzzer
Blue
3
Reader RD-4F appearance, destination of wires
(3) Connecting wires
(1) Holes for screws
(2)
(3) Control Unit’s PCB
(4) Terminals to connect to power supply unit, Reader RD-4F, EXIT button and lock
Holder for fixing the Control Unit on a DIN-rail
Control Unit KTM-600M appearance
Destination
Terminal
Door lock control
-DL
+DL
Supply voltage for
Control Unit and Lock
+E
Supply voltage for
Reader’s buzzer
BIP
Ground
RD Data
RG
Сontrol command OPEN
from EXIT button or
doorstation
OP
Ground
GND
1
2
3
4
Control Unit without the cover
www. 5VIZIT-KTM600F Operating Instruction (revision 10)vizit-group.com 1 11/201 -

FEATURES
·
·
·
·
·
·
·
·
Entrance door unlocking ACCESS keys
Entrance door unlocking by pressing the indoor EXIT button
Guard mode can be enabled disabled with a GUARD
or MASTER key All ACCESS keys are disabled in this mode
Programmable unlocked state duration
Light sound indication of operating modes
MASTER key memorizing
GUARD ACCESS keys memorizing and erasing
All data erasing
with (up to 2680 keys)
or key (up to 28 keys)
the - (1 key).
1 s or 7 s
and
-
and
PARTS LIST
SAFETY INSTRUCTIONS
2The product does not contain voltage above
Do not make any connections or repair when the power is on
Take care not to spill any liquids or chemically active substances on the product. Switch the power off before cleaning the
product. Clean by wiping with dry soft cloth. Do not use any liquid cleaners, aerosol cleaners or abrasive agents
.
.
.
8 VDC
Operating Instruction
x1
x1x1
CUontrol nit KTM600M Reader RD-4F
Fasteners
Screw - 4x40 Anchor - 6х40
for Control nitU KTM600M
x2 x2
for Reader RD-4F
Screw 4 4-х0
x2 x2
Gag
x 4
Anchor 4- 6х 0
www. 5VIZIT-KTM600F Operating Instruction (revision 10)vizit-group.com 2 11/201 -

www. 5VIZIT-KTM600F Operating Instruction (revision 10)vizit-group.com 3 11/201 -
MOUNTING LOCATION
Reader RD-4F
EXIT 300M button
The Reader is mounted on a wall near the entrance door,
or on a fixed door leaf, outside the entrance doorway.
The button is mounted on a wall near the entrance
door, inside the entrance doorway.
may
s
Note. Any button with NO contacts be used
as well. See the example of connection diagram
EXIT 300M
EXAMPLES OF WIRING DIAGRAMS
button is intended for use with an
electromagnetic lock to ensure lock release from
inside of the building.
in the section .
47 mm
75 mm
1100 100 mm±
47 mm
75 mm
1100 100 mm±
75 mm
Control Unit KTM600M
The Control Unit is located in any convenient place indoors.
Do not mount the unit near heating equipment.WARNING.
135 mm

SELECTION OF LOCK FOR VIZIT-KTM600F
VIZIT-KTM600F
Electromagnetic lock
VIZIT
IMPORTANT.
DO NOT use electromagnetic locks with resistance less than 20 Ohms, and not provided with a built-in degaussing
module.
Basic types of electric strikes, solenoid locks
Fail-locked (Fail-secure)
Note. VIZIT-KTM600F
The RF controller allows operation with different types of locks, such as electromagnetic locks, various
electric strikes, electromechanical solenoid locks.
The lock is blocked as long as the power is switched on. Once the current is switched off
or interrupted due to power failure, the lock is released and the door can be opened.
Recommended: electromagnetic locks ® with a built-in degaussing module, in combination with door closers
-
The RF controller does not support use of motor locks.
.
The strike / lock is blocked as long as the power is switched off. Once the voltage is switched
on, the strike / lock is released and the door can be opened.
Recommended: fail-locked strikes / solenoid locks with supply voltage 12 VDC and current consumption up to A.
-
The strike / lock is unblocked after a short power impulse, and remains
unblocked, even when the power is off. Once the door is opened and then
closed again, the strike / lock will resume its normal operation, and will be
blocked again.
Recommended: fail-locked strikes / solenoid locks with supply voltage 12 VDC and current consumption up to 1 A.
-
The strike / lock is blocked as long as the power is switched on. Once the voltage is switched
off or interrupted due to power failure, the strike / lock is released and the door can be opened.
Recommended: fail-unlocked strikes / solenoid locks with supply voltage 12 VDC and current consumption up to 0.6 A.
Fail-locked with hold-open function
Fail-unlocked (Fail-safe)
1
www. 5VIZIT-KTM600F Operating Instruction (revision 10)vizit-group.com 4 11/201 -

Settings with regard to the lock type
LOCK
ML
EL
TIME
1S
7S
IMPORTANT
VIZIT
In order to correctly set the lock control logic, unlocked time, and lock supply voltage, the KTM600M PCB has corresponding
jumpers installed:
The jumper determines the door lock control logic:
- position – a strike / lock is released when voltage is switched off.
- position – a strike / lock is released when voltage is switched on.
The jumper the unlocked state duration (1 or 7 seconds):
- position - unlocked state duration is 1 second.
- position - unlocked state duration is 7 seconds.
Some models of electric strikes and solenoid locks are provided with an integrated damper diode to eliminate pulse noise
after current off. If this is the case, the strike / lock has polar wiring.
If an electric strike or solenoid lock does not contain a damper diode, then connect a damper diode to the strike / lock's
terminals observing polarity, as shown in the picture below.
Do not connect a damper diode to electromagnetic locks , for they contain a built in degaussing module to eliminate
pulse noise.
determines
To provide power for the RF controller VIZIT-KTM600F and door lock, a power supply unit with output voltage 12 VDC to
18VDC and with rated current up to 1 A is recommended. Correct choice of a power supply unit depends on operating
voltage and current consumption parameters of the lock used in the system, as well as on the distance between a power
supply unit and the lock.
To provide power for an electromagnetic lock VIZIT, the power supply unit BPD18/12-1-1 or may
be used
When selecting a power supply unit for a particular model of electromechanical lock / strike, please consult qualified
personnel.
.
-
SELECTION OF POWER SUPPLY UNIT
Note. Do not use AC power adaptors.
19w/14.4v/EU(12V/1.5A)
.
Diode
1N4007
A white stripe on the case
indicates the diode’s cathode
+DL
-DL
+
-
Control Unit KTM600M
www. 5VIZIT-KTM600F Operating Instruction (revision 10)vizit-group.com 5 11/201 -

WIRING CABLES AND DISTANCES
Wiring is recommended to be done using a cable copper conductors
PVC PVC
with
with insulation and jacket
(1)
(2) (3).
2
1
3
Electromagnetic lock VIZIT
Circuit
Wire
Maximum length, m
Diameter, mm
Cross-section, mm20 2.05.
0 5. 0 8.
Power supply unit «Control Unit Reader«
Power supply unit Button for exit Electromagnetic lock««VIZITControl Unit «
50*
25
50*
50
* R C U shall
for a
Capacity of the cable connecting the eader to ontrol nit not exceed 3000 pF
(approx. 50 meters 2-wire cable).
2
Control Unit KTM600M
5
2
Reader RD-4F
EXIT 300M
button
Notes. EXIT 300M1. button is intended for lock release from inside of the building.
2. Recommended for use: power supply unit BPD18/12-1-1 orPower supply unit
19w/14.4v/EU(12V/1.5A).
is not supplied.
Electromechanical
lock / strike
2
4
2
Power supply unit
(1)
(2)
2
Control Unit KTM600M
Reader RD-4F
4
2
Power supply unit
Cross-sections of wires, and maximal distances are given in the table below:
VIZIT-KTM600F with Electromagnetic lock VIZIT
VIZIT-KTM600F with Electromechanical lock / strike
Wires cross-sections:
1. Power supply unit Control Unit Reader as shown in the above table.
2. Power supply unit Control Unit Electromechanical lock / strike wires cross-sections are selected with regard to:
operating voltage and current consumption parameters of the lock
output voltage of the power supply unit
distance between the power supply unit and lock
Therefore, consult qualified personnel about the lock, power supply unit and wires cross-sections.
««
««
-;
-;
-.
www. 5VIZIT-KTM600F Operating Instruction (revision 10)vizit-group.com 6 11/201 -

INSTALLATION
For qualified installation, wiring and servicing refer to technical and commercial partners of VIZIT TM. The list of
companies is given on VIZIT.EU ( .http://vizit.eu/eurounion/)
Reader RD-4F is mounted either on a wall, or on a fixed door leaf
Reader RD-4F mounting on a fixed door leaf ( )two methods
- Drill 2 holes (1) with diameter 5.5 mm
- Drill a hole for wires (2) with diameter 5 mm
Attach the Reader RD-4F to the and
fasten two screws ( ) .
screw on
- Drive in gags
.
-
М5 3
The length is chosen the condition:
door leaf thickness plus 5 mm.
(4).
fixed door leaf
()not supplied
49 mm
- Drill 2 holes (1) with diameter 6 mm and depth 40 mm.
- Drive anchors (2) into the holes.
- Drill a hole for wires ( ) with diameter 5 mm3.
60 mm
3
1
2
3
4
2
1
1
1
1
3
4
2
-
х0()
().
Attach the Reader RD-4F to the wall and
fasten two screws 4 4 4 in the anchors.
- Drive in gags 5
Note. Anchors and screws are supplied.
4
5
Reader RD-4F mounting on a wall
3
- Drill 2 holes (1) with diameter 3 mm
- Drill a hole for wires (2) with diameter 5 mm
Attach the Reader RD-4F to the and
fasten two screws 3.5x13 ( ) .
- Drive in gags
.
-
3
(4).
fixed door leaf
()not supplied
www. 5VIZIT-KTM600F Operating Instruction (revision 10)vizit-group.com 7 11/201 -
- Strip the ends of connecting wires that
will go to the Control Unit KTM600M, and
solder the ends to the Reader’s wires
following the diagrams given in the
section .
Put tightly over each soldered
connection a PVC tube or a heat-shrink
tube around 10 mm long (3).
PVC tubes and heat shrink tubes are
not supplied
-
EXAMPLES OF WIRING DIAGRAMS

Control Unit KTM60 M0
The Control Unit may be mounted either on a wall, or a DIN-rail.
-
- (4) coming from the power supply unit, Reader RD-4F, EXIT 300M button and lock.
- Connect the ends to the C U ’s terminals 5
- S (6) on the C U ’s PCB (7)
ontrol nit ( )
et jumpers ontrol nit according to the table :
U C U ’s cover (2)
nfasten two screws (1) and take off the ontrol nit .
Cut the plastic parts 3 off the cover.
Strip the ends of connecting wires
-()
EXAMPLES OF WIRING
DIAGRAMS
following the diagrams given in the section
.
3
Lock Type Jumper
Fail-locked strike / lock (12 VDC / 1 A max.)
LOCK
ML
TIME
7s
Electromagnetic lock
Fail-unlocked strike / lock (12 VDC / 0.6 A max.)
VIZIT
Fail-locked strike / lock with hold-open function (12 VDC / 1 A max.)
EL 7s
EL 1s
3
1
2
4
5
6
- Drill 2 holes (1) in a wall, with diameter 6 mm and depth mm
- Drive anchors (2) into the holes
Attach the Control Unit to the wall and fasten screws 4x40
in the anchors
Note. Anchors and screws are supplied
.
.
- 2 (3)
.
.
40 ( ) Bosses on the Control Unit’s base
( ) rail with width mm and
thickness mm
( ) Holder for fixing
1-
2 - DI - 35
1-2
3-
N
1
2
3
1
2
3
KTM600M mounting on a railDIN-KTM600M mounting on a wall
ML EL PRG 1S 7S
-DL +DL BIP+E RDGND RG OP
7
www. 5VIZIT-KTM600F Operating Instruction (revision 10)vizit-group.com 8 11/201 -

EXAMPLES OF WIRING DIAGRAMS
RF Controller with electromagnetic lock VIZIT-ML240-40VIZIT-KTM600F
-DL
+DL
BIP
+E
RD
GND
RG
Reader
RD-4F
Black
White
Blue
Red
Green
Button
МEXIT 300
Black
White
Blue
Red
-DL
+DL
Electromagnetic
lock VIZIT-ML240-40
+DL
-DL
+E
OP
RG
RGRG
+E RD
RD
BIP
BIP OP
OP
-12
-18
+12
+18
+E
GND
BPD
Power upplys unit
18/12-1-1
Q1
ML
Q2
TIME
C2
R1
LOCK
EL
7S
1S
D4
MEMORY CHIPMEMORY CHIP
PROGRAMPROGRAM
PRG
Note. Power supply unit
19w/14.4v/EU (12V/1.5A)
may be used instead of
BPD-18/12-1-1
RF-key
VIZIT-RF3.1
Antenna +E GND
RF Controller with electromechanical lock / strikeVIZIT-KTM600F
-DL
+DL
BIP
+E
RD
GND
RG
Black
White
Blue
Red
-DL
+DL
+E
OP
RG
RGRG
+E RD
RD
BIP
BIP OP
OP
Button for exit
required for keys
memorizing / erasing)
(
Q1
ML
Q2
TIME
C2
R1
LOCK
EL
7S
1S
D4
MEMORY CHIPMEMORY CHIP
PROGRAM
PRG
КТМ600М
Reader
RD-4F
RF-key
VIZIT-RF3.1
IN-LINE
DC JACK
+E
GND
+E GND
Control Unit KTM600M
Antenna
+DL
-DL
Electromechanical lock / strike
Diode
1N4007
A white stripe on the case
indicates the diode’s cathode
DC 12V
19w/14.4v/EU(12V/1.5A)
Power upplys unit
Note. Power supply unit
19w/14.4v/EU (12V/1.5A)
BPD-18/12-1-1 may be
used instead of
www. 5VIZIT-KTM600F Operating Instruction (revision 10)vizit-group.com 9 11/201 -

KEY MEMORIZING AND ERASING FROM THE CONTROL UNIT MEMORY
“Key No…- User”
MASTER-key memorizing
PRG
PRG
N
ACCESS keys memorizing
N
GUARD keys memorizing
N
ACCESS and GUARD keys erasing
1
“Key No…- User”
N2
’S
ote.
ote.
ote.
Note .
ote .
keys the installation
C U R 300M (or button for exit)
T are
and
Lost key erasing
U memorizes 2680
, 28 , approach
close ’s antenna Make records of key numbers and their users, for this
list ( ) may be
Take off cover from the Control Unit remove
is ing
Approach close ’s antenna are sounding: the MASTER-key has been
memorized. affect
put cover back
f have been approached to the reader’s antenna only will be
Move the close to ’s antenna and hold it
are ing
roach a key close ’s antenna to memorize it as an S are
ing: the key has been memorized.
A single indicates : in the memory, the key is faulty.
To memorize the next , approach a new key close ’s antenna
When done with memorizing, approach to the reader’s antenna.After two , approach
the reader to the
After 2680 ’ have been memorized, are ing
not available
Move the close to ’s antenna and hold it
are ing
300M . O is sounding the is illuminating
roach a key close ’s antenna to memorize it as a GUARD are
ing: the key has been memorized.
To memorize the next GUARD , approach a new key close ’s antenna
When done with memorizing, approach to the reader’s antenna, the system will return the
.
After 28 have been memorized, are ing
not available
Move the close to ’s antenna and hold it
are ing
Approach to the reader’s antenna, t are sounding the is illuminating
roach you want to close ’s antenna s are ing: this key
has been deleted from the system’s memory
Asingle indicates : does not in the memory.
To erase the next , approach it close ’s antenna
When done with erasing, approach to the reader’s antenna, the system will return the
.
After a key has been erased, its is cleared F on, d key
memory when list
may only
Memorizing of ACCESS, GUARD and MASTER-key is recommended to be performed before .
To memorize or erase keys, connect the ontrol nit, eader and EXIT button following
he following modes available:
MASTER-key memorizing
ACCESS GUARD keys memorizing / erasing
Erasing of all data
The Control nit each key code in the next free memory cell numbering them from No1 up to No
for ACCESS keys and from No1 up to No for GUARD keys. Enumerate ACCESS keys beforehand and
them one by one to the reader during memorizing.
useful for key management in case of a lost key.
Turn the power off.
the and the jumper.
Turn the power on. A long beep sound .
a key to the reader . One short and two long beeps
MASTER-key memorizing does not other settings.
To quit this mode, turn the power off, restore the jumper to its place and the .
I several keys , the last one memorized as the
MASTER-key.
MASTER-key the reader for 5 seconds at least. The lock is released, short beeps
and three long beeps sound . Take the MASTER-key off before the third long beep ends.
App to the reader ACCES key. One short and one long beeps
sound
long beep (without a short one) an error the key already exists or
ACCESS key to the reader , and so on.
the MASTER-key briefly long beeps
it again to return to ACCESS mode.
user s keys 5 short beeps sound . Further memorizing of ACCESS keys is
.
MASTER-key the reader for 5 seconds at least. The lock is released, short beeps
and three long beeps sound . Take the MASTER-key off before the third long beep ends.
Press the EXIT button briefly ne long beep , LED .
App to the reader key. One short and one long beeps
sound
key to the reader , and so on.
the MASTER-key briefly to
ACCESS mode
GUARD keys 5 short beeps sound . Further memorizing of GUARD keys is
.
MASTER-key the reader for 5 seconds at least. The lock is released, short beeps
and three long beeps sound . Take the MASTER-key off before the third long beep ends.
the MASTER-key briefly wo long beeps , LED .
App a key erase to the reader . One short and one long beep sound
.
long beep (without a short one) an error the key exist
key to the reader , and so on.
the MASTER-key briefly to
ACCESS mode
memory cell . urther uring memorizing, a key code will be
stored in the first clear cell found. Take it into account managing .
Key No1 (ACCESS or GUARD) be erased under condition of all keys erasing.
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
the
diagrams given in the section .EXAMPLES OF WIRING DIAGRAMS
www. 5VIZIT-KTM600F Operating Instruction (revision 10)vizit-group.com 10 11/201 -