VMP VH-001 User manual

325 Log Canoe Circle • Stevensville MD 21666 • www.videomount.com
Phone: [phone] • Fax: [phone]
VH-001
WARNING: The installer of these products must verify that the mount surface, ceiling
or wall, will safely support the combined weight of all attached equipment and
hardware. Video Mount Products will not be held liable for the improper use or
installation of its products.

1. Before starting lay out all parts to your mount and match them to the parts list
provided. Verify that you have all your parts before attempting to assemble the mount.
2. To determine which steps to follow first determine which mount you are trying to
attach the VH-001 to. If you are trying to connect the VH-001 to a W-13 or a C-13
proceed to step 3. If you are trying to connect the VH-001 to a C-20, C-27, W-20, or W-
27 proceed to step 6. If you are trying to connect the VH-001 to a new style
VMP014/024, VMP036/038, VMP042/044, or VMP046/048 proceed to step 9. If you
are trying to connect the VH-001 to a VMP001, VMP003, or VMP006 proceed to step
11. Note: Instructions assume that you have already assembled the primary mount.
3. First remove the TV from the
mount. Next remove the platform (#1 for
the W-13 or #4 for the C-13) by removing
the nylon nut and washer (#10 and #4 for
the W-13 or #10 and #8 for the C-13).
4. Next remove the plastic swivel (#7
for both the W-13/C-13). Snap off the
plastic circle on the plastic swivel (#7 on
both) and remove the 2.5” long screw (#13
on the W-13 and #5 on the C-13).
5. Attach the VH-001 force arm (#1 for VH-001)
to the bottom of the plastic swivel by inserting the
100 mm long screw (#10 on the VH-001) through the
platform (#1 for the W-13 or #4 for the C-13) and
using the 10mm spacer (#11 for the VH-001) in
between the plastic swivel (#7 on the W13/C13) and
securing the screw (#10 on the VH-001) with the
plug, washer and nylon nut (#12, #13, and #14 on the
VH-001). Once this is completed please skip to step
14.
Step 3 : Removing the platform
from the W-13/C-13
Step 4 : Removin
g
the plastic
connector and swivel
Step 5 : Attaching the force arm

6. First remove the platform (#1 for
W20/W27 and #4 for C20/C27) by
removing the washers and nylon nuts (#4
and #12 for W20/W27 and #8 and #10 for
C20/C27) from the depressions in the
platform.
7. Next insert the M6 screw that is 80 mm long
(#15 for the VH-001) through the top of the force
arm (#5 for W20/W27/C20/C27) and place the
spacer (#16 for the VH-001) around the screw
underneath the force arm (#5 for
W20/W27/C20/C27).
8. Finally connect the VH-001
force arm (#1 for VH-001) by
inserting the M6 screw (#15 for the
VH-001) through and securing with a
plug, washer, and nylon nut (#12, #17,
and #18 for the VH-001) and reattach
the platform by reversing step 6. Once
this is completed please skip to step
14.
9. First connect the connector (#25 for
the VH-001) to the lower force arm (#24 for
VMP014/024, #20 for VMP036/038, and #17
for VMP042/044 and VMP046/048) using M6
screws that are 12 mm long (#26 for VH-001).
Step 6 : Removing the platform
Step 8 : Attaching the
VH-001 force arm
Step 7 : Inserting the connector screw
Step 9 : Attaching
the connector

10. Next attach the VH-001 force arm (#1 for VH-
001) to the connector (#25 for the VH-001) using a
3/8” screw (#24 for VH-001) and a washer (#13 for
VH-001) in between the connector and the force arm.
Insert a brake screw (#23 for VH-001) into the
connector using the M3 Allen key (#9 for VH-001) to
tighten it down onto the 3/8” screw. Once this is
completed please skip to step 14.
11. First
remove the nylon
nut (#12 for
VMP001, #14 for
VMP003, and #11 for VMP006) from the bottom
from the fixed bracket (#4 for the VMP001 and
VMP003) or the 3/8” screw (#9 for the VMP006).
12. Next
replace the nylon
nut with the 27
mm long nut (#27
for VH-001) and
tighten the brake
screw (#23 for VH-001) onto the fixed bracket (#4 for
the VMP001 and VMP003) or the 3/8” screw (#9 for
the VMP006) using the M3 Allen Key (#9 for VH-
001).
13. Now attach the VH-001 force arm (#1 for VH-001) by
inserting a washer (#13 for VH-001) between the nut (#27 for VH-
001) and force arm and then using the 3/8” screw (#24 for VH-
004) attach the force arm to the nut. Then use a brake screw (#23
for VH-001) to secure the 3/8” screw in the nut. Once this is
completed please proceed to step 14.
Step 10 : Attaching the force arm
Step 11 : Removing
the nylon nut
Step 12 :
Attaching
the long nut
Step 13 : Attaching
the force arm

14. Now that the VH-001
force arm (#1 for VH-001) is
attached it is time to assemble
the VH-001. First attach the
non-skid padding (#7 for VH-
001) to the adjustable stopper (#3
for VH-001). Next attach the
adjustable stoppers (#3 for VH-
001) to the extension holder (#2
for VH-001) using the butterfly
nuts and ¼” – 20UNC screws
(#5 and #4 for VH-001).
15. Now take the Velcro (#6 for VH-001) and apply it to the equipment you are going
to place in the VH-001 and on the extension holders (#2 for VH-001). You should apply
the Velcro to the bottom left and right sides of your equipment along the edges.
16. Insert the extension holders
(#2 for VH-001) into the force arm
(#1 for VH-001). Slide the desired
equipment in between the adjustable
stoppers and both extension holders
(#3 and #2 for VH-001). Secure the
position of the extension holders by
tightening down brake screws (#8
for VH-001) into the force arm while
making sure the equipment is
centered in the bracket. Lastly
tighten the adjustable stoppers down
onto the top of the equipment.
Enjoy your mount!
Step 14 : Assembling the
extension holders
Step 15 :
Applying Velcro
Ste
p
15 : A
pp
l
y
in
g
Velcro
Step 16 : Securing the
equipment in the VH-001 (VH-
001 is shown without being
attached to a mount for clarity)