VMP LCD-1C User manual

LCD-1C, LCD-1CB & LCD-1 CW
Instruction Sheet For:
For more information, please contact us at:
345 Log Canoe Circle, Stevensville, Maryland 21666
Toll Free: 877.281.2169 Phone: [phone] Fax: [phone]
www.videomount.com

1
18
19
2
15
17
22 21
20
14
13
11
10
8712
5
4
9
3
16
24
23
LCD-1C
ITEM
NO.
DESCRIPTION
QTY.
1
Ceiling Plate
1
2
Extension Tube
1
3
Support Tube
1
4
Swivel Bracket
1
5
Mounting Plate
1
7
Nylon Nut M6*P1.0
1
8
Nylon Nut 3/8"-16UNC
1
9
Screw M6*P1.0*L35
1
10
Screw M12*P1.75*L65
1
11
Washer
1/2"*
32mm
2
12
Adjusting Screw 1/4"-
20UNC*50mm
1
13
Cable Clips
2
14
End Plug
2
15
Washer
3/8"*
19*T1.6
2
16
Screw 3/8"-16UNC*L2"
1
17
Brake Screw 1/4"-20UNC*L3/8"
1
18
Screw 5/16"-18UNC*L1-1/2"
1
19
Nylon Nut 5/16"-18UNC
1
20
M3 Allen Key
1
21
Screw M4*P0.7*L12
4
22
Screw M5*P0.8*L12
4
23
Lag Screw 5/16"*L2.5"
4
24
Washer
8.3*
19*T1.6
4

Step 1
Before starting, lay out all parts to your mount and match them to
the parts list provided. Verify that you have all your parts before
attempting to assemble the mount.
Step 2
Attach the mounting plate to the LCD using the M4 or M5
screws.
Step 3
Mark the ceiling or desired mounting surface in preparation of in-
stallation of ceiling plate . If mounting to wooden ceiling joists,
pre drill pilot holes using a 7/32” drill bit. Attach the ceiling plate
to the wooden ceiling joist using the 5/16” by 2.5” long lag screw
and washer . WARNING: Please verify that your mounting
surface will support the combined weight of your mount, mount-
ing hardware, and flat panel. Also verify that the mounting sur-
face is safe to drill through. Please note only mounting hardware
for mounting to wooden ceiling joists will be provided with the unit.
If mounting to a surface other than wooden ceiling joists then other
hardware will be required. If in doubt or uncertain about any of the
above, please contact a professional installer.
Step 4
Attach the swivel bracket assembly from step 2 to the support tube
using the 3/8” screw , washers and nylon nut . Insert
adjustable screw into the back of the swivel bracket for
use when tilting the monitor.
Step 2: Attaching the mounting
plate to the LCD
Step 3: Attaching the ceiling
plate to the ceiling
Step 4: Attaching the swivel
bracket to the support tube
21
1
522
1
315
12
8
16
4
23 24

Step 5
Attach the support tube to the extension tube using the
M12 screw and washers .
Step 6
Attach the extension tube to the ceiling plate using
the 5/16” screw and nylon nut . Secure the M12 screw
from slipping in the extension tube by tightening the ¼”
brake screw into the threaded hole in the side of the exten-
sion tube using the Allen key .
Step 7
Attach the mounting plate to the swivel bracket using
the M6 screw and nylon nut .
Step 8
Insert end plugs into the support tube . For cable man-
agement, insert the cable clips by pushing the arrow ends
into the square holes in the support tube .
Please verify that all nuts and screws are securely tightened.
Step 5: Attaching the support
tube to the extension tube
Step 6: Attaching the extension
tube to the ceiling plate
Step 7: Attaching the
mounting plate to the
swivel bracket
WARNING: The installer of these products must verify that
the mounting surface, ceiling or wall, will safely support the
combined weight of all attached equipment and hardware.
Video Mount Products will not be held liable for the improper
use or installation of its products.
Enjoy Your Mount!
10
32
11
14
20
2
5
2
18
4
13
7
17
19
2
9
1
10
3
3