VMP FP-LFV User manual

FP-LFV & FP-LFVB
Instruction Sheet For:
For more information, please contact us at:
345 Log Canoe Circle, Stevensville, Maryland 21666
Toll Free: 877.281.2169 Phone: [phone] Fax: [phone]
www.videomount.com

2
3
1
22
21 24
6
23
2019
18171615
14
13
12
11
10
9
7 8
5 4
FP-LFV
ITEM
NO.
DESCRIPTION
QTY.
1
Wall Plate
2
2
Vertical Support
2
3
Screen Mounting Bracket
2
4
Cross Screw M4*P0.7*L6
6
5
Security Screw M5*P0.8*L20
2
6
Long Allen Key M4
1
7
Cross Screw M4*P0.7*L12
4
8
Cross Screw M5*P0.8*L12
4
9
Cross Screw M6*P1.0*L12
4
10
Cross Screw M8*P1.25*L16.5
4
11
Cross Screw M4*P0.7*L30
4
12
Cross Screw M5*P0.8*L30
4
13
Cross Screw M6*P1.0*L35
4
14
Cross Screw M8*P1.25*L40
4
15
Lock Washer M4
4
16
Lock Washer M5
4
17
Lock Washer M6
4
18
Lock Washer M8
4
19
Washer
5.5*
18*T2.0
4
20
Spacer M6
4
21
Spacer M8
4
22
Magnetic Level
1
23
Lag Screw 5/16"*2.5"
6
24
Washer
8.3*
19*T1.6
6

Step 1
Before starting, lay out all parts to your mount and match them to the
parts list provided. Verify that you have all your parts before attempt-
ing to assemble the mount.
Step 2
Assemble the wall plate by attaching the two horizontal wall plates
using the vertical supports and short M4 screws .
Step 3
Mark the wall or desired mounting surface in preparation of installation
of wall plate assembly and . If mounting to wooden studs, pre
drill pilot holes using a 7/32” drill bit. Attach the wall plate assembly
and to the wooden stud using the 5/16” by 2.5” long lag screw
and washer .
WARNING: Please verify that your mounting sur-
face will support the combined weight of your mount, mounting hard-
ware, and flat panel. Also verify that the mounting surface is safe to drill
through. Please note only mounting hardware for mounting to wooden
studs will be provided with the unit. If mounting to a surface other than
wooden studs then other hardware will be required. If in doubt or uncer-
tain about any of the above, please contact a professional installer.
Step 4
Determine the correct screw size and if you need to use washers, lock
washers, or spacers. Note: Spacers are used for TVs with recessed hole
patterns. Secure the TV to the mounting rails using the appropriate
hardware through . Note: The brackets have to be level with
each other to work properly.
Step 5
Use the hooks in the mounting rails to hook on the top rail of the wall
plate assembly . Use security screws and the long allen key to
secure the TVs to the bottom rail and to secure its horizontal position.
Please verify that all nuts and screws are securely tightened.
Step 2: Assembling the wall plate
Step 3: Mounting the wall plate
WARNING: The installer of these products must verify that the mount
surface, ceiling or wall, will safely support the combined weight of all
attached equipment and hardware. Video Mount Products will not be
held liable for the improper use or installation of its products.
Enjoy Your Mount!
Step 4A: Attaching the mounting
brackets to the flat panel (spacers
not needed)
Step 5: Securing the mounting
brackets
Step 4B: Attaching the mounting
brackets to the flat panel (spac-
ers needed)
1
1
3
2
1
1
3
2
6 5
23
4
12
24
721