Vogue WALL UNIT 600 Tall Adjustable Corner User manual

WALL UNIT
600 Tall Adjustable Corner Assembly Guide
For Internal Use:FI.WR.INS.048_WKIN00133_Wall_600_AdjCnr_Tall.Rev8

Page 1
WALL UNIT
600 Tall Adjustable Corner Assembly Guide
REQUIRED TOOLS
NOT to be used
with CAM DOWEL
& CAM LOCK
Panel B
x2 End Panel
Loose Shelf
x3
Blanking Panel
x1
Frontal
(packed separately)
x1
Panel A
x1 Back Panel
Panel C
x2 Base Panel
(F) x8
Wooden Dowel
(G) x8
Cam Dowel
(Expanding)
(H) x8
Cam Lock
(K) x4
30mm
Screw
(L) x21
15mm
Screw
(S) x4
20mm
Screw
(M) x2
Cover Cap
(FF) x2
L Bracket
(N) x1
Door
Buer
(Z) x12
Shelf Peg
Plastic
(T) x10
Back Panel
Support Clip
Hanging Bracket
x2 Inc Screws
Hanging
Bracket Plate
x2 (Screws NOT included)
Hinge
Mounting Plate
x4 Inc Screws
Hinge
x4 Inc Screws
Corner
Gusset
x2
Hanging Bracket
Cover Cap
x2
BEFORE YOU START
INSTALLATION
SHOULD BE
PERFORMED BY A
COMPETENT
PERSON ONLY.
THIS PRODUCT COULD
BE DANGEROUS
IF INCORRECTLY
INSTALLED

Page 2
For Internal Use: FI.WR.INS.048_WKIN00133_Wall_600_AdjCnr_Tall.Rev8
C
C
A
B
Step 1.
Seat dowel (F)
into holes in
end panel (B) as
shown.
Step 2.
Seat cam dowel (G)
into holes in
end panel (B) as shown.
Step 4.
Slide panel (A) into the
groove of panels (B) and
x 2 (C).
Step 5.
Insert cam lock (H).
Hand tighten all cam locks (H),
this will expand the
cam dowels (G) and tighten the
unit together.
All cam locks (H) are to be positioned facing the
outside of the unit carcase, for ease of tightening. Do not use power tools with
cam dowel (G) or cam lock (H)
Dowel (F)
& Cam Dowel (G)
location detail
Seat (G)
cam dowel
into hole as
shown.
B
G F F G
Step 3.
Attach panels x2 (C) to panel
(B), using cam dowels (G)
(in blue) and also using
dowels (F) (in orange) in
positions as shown.
G F F G
View from underside
B
C
G
G
C
H
H
View from underside

Page 3
WALL UNIT
600 Tall Adjustable Corner Assembly Guide
Step 8.
Attach panel (B) to
panels (C) using cam
dowel (G)(in blue) and
also using dowels (F) (in
orange) in positions as
shown. Ensure panel (A)
is seated into the groove
of panel (B).
All cam lock (H) are to be positioned facing
the outside of the unit carcase, for ease of tightening. Do not use power tools with
cam dowel (G) or cam lock (H)
Step 9.
Insert cam lock (H). Hand
tighten all cam locks (H), this
will expand cam dowels (G) and
tighten the unit together.
C
C
A
B
B
Step 6.
Seat dowel
(F) into holes in
both end panels
(B) as shown.
Step 7.
Seat cam dowel (G)
into holes in both end
panels (B) as shown.
Dowel (F)
& Cam Dowel (G)
Location Detail
GF F G
GFFG
B
B
CC
H
H
G
G
View from underside
View from underside
Seat (G)
cam dowel
into hole as
shown.

Page 4
For Internal Use: FI.WR.INS.048_WKIN00133_Wall_600_AdjCnr_Tall.Rev8
Step 10.
Ensure unit is square.
Step 11.
Slide the back panel clips (T) into the groove of both panels (B).
The back panel clips (T) should be evenly spaced as shown and
positioned to allow the hanging bracket and corner gussets to be
tted.Onceinplace,tightenscrew.
Step 12.
Attach hinge mounting plates onto end panels (B) as shown
using screws which are already located within the hinge
plates.
Hinge side or sides to be mounted in accordance to
Customer Specic Kitchen Plan.
A
T
A
T
126mm
94mm
94mm
126mm
From Bottom
From Top
B
A
B
C

Page 5
WALL UNIT
600 Tall Adjustable Corner Assembly Guide
B
A
Step 14.
Secure corner gussets
to the bottom left and
right hand side of the
wall unit using 4 x 15mm
screws (L) per plate.
Step a
Insert hanging
bracket into pre-drilled holes
Step c
Secure with provided
2 x 20mm screws (S) per bracket
Step b
Rotate locking
lever 180 degrees
Detail A Detail A
S
S
Detail A
View through
Back Panel
Pilot
hole
M
Detail B
Step 13.
Hanging Brackets steps a,b & c to
be carried out on both sides as
shown
Care to be taken. Hanging procedure is necessary for a safe installation.
Screws for attaching to walls are not provided as these vary depending on materials,
thicknessandconstruction.Ensureappropriatexingsforwallconstructionareused.
L
L
L
L
Detail B
Step 15.
Drill a small pilot hole through the centre of the corner gussets,
through the back of the unit. Use this hole at the end of the
process to screw through and into the wall. Cover the screw
heads using the cover caps (M) provided.
Screws for xing to walls are not provided as these vary
depending on your wall material and construction. Ensure
appropriate xings for wall constructions are used.

Page 6
For Internal Use: FI.WR.INS.048_WKIN00133_Wall_600_AdjCnr_Tall.Rev8
K
Step 16.
Measure appropriately and
attach the 2 x hanging bracket
plates onto the wall screwing
through the provided holes into
your wall.
Step 17.
Hang the unit using the
brackets to hook onto the
plate as shown
Hanging Bracket
Plate
Step 18.
Using points a, b & c adjust the unit to suit.
Step a.
Rotate the screw clockwise
to move the unit up.
Anti-clockwise for down.
Step b.
Adjust the depth
using centre screw.
Step c.
Screw the red screw until it
touches the plate to lock
in position.
Hanging
Bracket
viewed through
Back Panel
b
C
c
a
a
b
Step 19.
Screw into any side units using the provided 2 x 30mm screws (K) to secure the
unit. Screw just to the rear of the hinge plates then place cover caps (M) on the
heads to conceal it.

Page 7
WALL UNIT
600 Tall Adjustable Corner Assembly Guide
Step 20.
Attach panel (X) to panel (Y) using appropriate
xing.
Adapt panels (X) & (Y) where applicable to
suit Customer Specic Kitchen Plan.
Step 21.
Attach panels (X) & (Y) to the unit using the
2 x L brackets (FF) and the 4 x 15mm screws (L) at the top
and bottom as shown.
Step 22.
Measure and cut down blanking panel to required size.
Attach to unit using 7 x15mm screws (L), evenly spaced as
shown.
Ensure you screw into the centre of the base panels as
shown (9mm from the edge).
X
Y
Adjustable Corner Post Pack
X
Y
Panel X
x1
Panel Y
x1
LL
L
L
L
LL
9mm
View from
inside
View from
inside
FF
L
FF
L

Page 8
For Internal Use: FI.WR.INS.048_WKIN00133_Wall_600_AdjCnr_Tall.Rev8
Step 23.
Insert hinge in top & bottom holes as shown below.
Step 24.
Secure hinges by tightening
2 x screws with hinge dowels
attached. These are already
positioned within the hinges.
Step 25.
Attach the door to unit
where required. To attach
door, clip hinge onto hinge
plate and click to secure.
Hinge Cover Caps
Step 27.
Fit cover caps to hinge.
Adjust Soft close to suit.
Step 26.
Adjust hinge to suit. As shown below.
To adjust hinge using
a screw driver, tighten
or loosen as required at
points 1& 2.
Point 1- In - Out
Point 2- Left - Right
12
FRONTAL
HINGE
ADJUSTMENT
Hinge Plates
View from inside of unit
To release door,
pull catch as shown,
to release hinge from
the hinge plate.
The top and bottom
hinges MUST be
adjusted to the SAME
STRENGTH.
To Move the
hinge up/down,
loosen screws
A + B,
Manoeuvre
the door, then
re-tighten the
screws
A
B

Page 9
WALL UNIT
600 Tall Adjustable Corner Assembly Guide