Volt VUL-6803-25-BBZ User manual

VOLT®Low Voltage Landscape Lighting
VOLT®RGBW Salty Dog Integrated LED Brass Underwater Light (Bronze)
VUL-6803-25-BBZ
INSTALLATION INSTRUCTIONS
Specications and product details subject to change without notice.
© Copyright 2022, VOLT® Lighting, Lutz FL USA 33549 • All rights
reserved. [email protected] • 813.978.3700
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)
- 1 -

VOLT®RGBW Salty Dog Integrated LED Brass Underwater Light (Bronze)
VUL-6803-25-BBZ
Important: Please Read Before Installation
INSTALLATION INSTRUCTIONS
!
www.voltlighting.com
- 2 -
This luminaire is intended for installation in accordance with local codes
and the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situations.
1. Make sure that the power is turned OFF before installing or servicing this
luminaire.
2. WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M)
or more from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply
(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with UL listed wire connectors that are
suitable for outdoor use.
5. Position the low voltage wire and wire connector so that it is located
within 6 inches (15.2 cm) from a building structure, a luminaire or tting.
6. The main low voltage cable is intended for shallow burial - less than 6
inches (152 mm).
7. “WARNING - RISK OF ELECTRIC SHOCK”
• Use only in ponds and small decorative fountains where persons will
immerse no more than their hands and lower arms while the product is
energized.
• DO NOT use in water intended for swimming, wading, immersion, or
bathing.
• All installer completed cable connections must be located outside of pond
or fountain.
• Low voltage circuit must be supplied by a power unit marked as suitable for
supplying submersible luminaires.
• Power unit must be supplied by a circuit protected by a ground fault circuit
interrupter (GFCI).
• “Maximum depth: 18 in (450 mm)”.

[email protected] • 813.978.3700
Package Contents
A. (1) Fixture body
Parts (sold seperately)
A. (3) Mounting Screws
B. (3) Flat Washers
C. (3) Anchors
Product Dimensions
Important Safety Instructions
!
- 3 -
5”
4”
5”
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – TO REDUCE THE RISK OF FIRE OR INJURY TO PERSONS.
1. Turn o/unplug and allow to cool before replacing lamp.
2. Lamp gets HOT quickly! Contact only switch/plug when turning on.
3. Do not touch the hot lens, guard or enclosure.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may damage lamp.
6. Do not operate the luminaire tting with a missing or damaged shield.

www.voltlighting.com
Install Horseshoe Mount
1
INSTALLATION INSTRUCTIONS
- 4 -
Wire Connection
2
VOLT®RGBW Salty Dog Integrated LED Brass Underwater Light (Bronze)
VUL-6803-25-BBZ
Place the horseshoe mount on the
desired location and mark (3) points
for the anchors from the holes on the
horseshoe mount.
Drill proper holes on the location and
insert anchors into the drilled holes.
Attach the horseshoe mount onto
the anchors. Pass the washers over
the mounting screws and thread the
mounting screws into the anchors to
secure the horseshoe mount. Hand
tighten until snug with a screwdriver.
NOTE: SOME APPLICATIONS ARE NOT
SUITABLE FOR PERMANENT MOUNTING
AND DO NOT REQUIRE OR WARRANT THE
USE OF SCREWS AND ANCHORS
Anchor
Horseshoe
Mount
Mounting
Screw
Washer
Strip both leads from the luminaire pigtail. Using wire connectors
(sold seperately), connect the leads from the luminaire to the main
supply cable leads.
Adjust the housing to your desired direction by using the lock nuts
on the side of the housing.
Lock Nut
Wire Connector
Main Supply Wire
Pigtail
Housing

[email protected] • 813.978.3700
- 5 -
Install/Replace Glare Guard
Remove Faceplate
1
Install Glare Guard
2
Loosen the screws on the
faceplate and remove the
faceplate from the housing.
Screw
Faceplate
Housing
Housing
Install the glare guard onto the
housing and secure it with the
screws previously removed,
tightening them in a star pattern.
Now you can power on the
system, and the light is 2700K
and the optic is 60 degree as
default.
Glare
Guard
Screw

www.voltlighting.com
INSTALLATION INSTRUCTIONS
- 6 -
VOLT®RGBW Salty Dog Integrated LED Brass Underwater Light (Bronze)
VUL-6803-25-BBZ
Remove Faceplate and Lens
1
Replace Optic
2
Install/Replace Opc
Loosen all screws on the faceplate.
Remove the faceplate and lens from
the xture.
xture
Screw
Faceplate
Lens
xture
Screw
Loosen the screws and remove
the optic from the xture.
Install the new optic in the
xture. Make sure that you have
the optic properly aligned over
the LED board before tightening
down. Improper alignment when
tightening the screws can cause
the optic to break.
Optic

Reinstall Lens and Faceplate
3
- 7 -
IR Remote (Oponal)
Remove the Battery compartment Cover
1
Place the lens and faceplate back
onto the xture. Secure them with
previously removed screws. Tighten
until snug with screwdrivers.
xture
Screw
Faceplate
Lens
An IR Remote is optional for this xture. The IR remote requires two AAA
batteries.
1
2
3
Press the tab and lift the battery
compartment cover to remove it
from the IR Remote.
Ta b
Cover
Backing
IR Remote

INSTALLATION INSTRUCTIONS
www.voltlighting.com
- 8 -
VOLT®RGBW Salty Dog Integrated LED Brass Underwater Light (Bronze)
VUL-6803-25-BBZ
Install Two AAA Batteries
2
Install the Battery compartment Cover
3
+
-
+-
Place two AAA batteries into the
battery compartment properly.
AAA Battery Battery
Compartment
Backing
IR Remote
1
2Place the battery compartment
cover back onto the IR Remote.
Ta b
Cover
Backing
IR Remote

[e-mail] • 813.978.3700
- 9 -
IR Remote Functions
4
OFF ON
R B
W
G
FLASH
FADE
SMOOTH
STROBE
2
3
4
1
5
6
7
8
1. On
2. O
3. Brightness Control
4. 16 color selections
5. Flash
• Mode 1: Repeats Red, Green,
Blue + color cycle for 1
second duration of each of
the seven colors within this
mode.
• Mode 2: Hit ash a second
time and this mode slowly
blends the same seven
colors from mode one,
mixing them together.
6. Strobe
• Mode 1: Pick any color on the remote, then press strobe and that
color will strobe every second alternating between on and o.
• Mode 2: Hit strobe a second time and this mode will strobe a
blended white color at the same speed as before.
7. Fade
• Mode 1: Pick any color on the remote, then press fade and that
color will slowly fade in and out every second.
• Mode 2: Hit fade a second time and it will fade a blended white
color in and out at the same speed as before.
8. Smooth
• Mode 1: Repeats a ash cycle of Red, Green, and Blue only.
• Mode 2: Hit smooth a second time and this mode slowly blends Red,
Green, and Blue only; in and out of each other at the same speed.

INSTALLATION INSTRUCTIONS
www.voltlighting.com
- 10 -
VOLT®RGBW Salty Dog Integrated LED Brass Underwater Light (Bronze)
VUL-6803-25-BBZ

[e-mail] • 813.978.3700
- 11 -

Specications and product details subject to change without notice.
© Copyright 2022, VOLT® Lighting, Lutz FL USA 33549 • All rights
reserved. [email protected] • 813.978.3700
www.voltlighting.com
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)
- 12 -