Volter BEACH-set User manual

1
OPERATING INSTRUCTIONS FOR THE ACCESSORY
BEACH-set
TO THE PRODUCT xRover
Thank you for purchasing the BEACH-set accessory for the xRover REHA cart and we
believe that it will serve you for a long time.
XRover cart - with the BEACH-set accessory can be used to transport people on sandy
terrain (beach / desert).
The xRover REHA product complies within the following standards:
CSN EN 1888: 2012 - as a pram
CSN EN 15918: 2013 - as a cart behind a wheel
CSN EN 12189: 2014 - as a wheelchair.
Technical parameters:
-rear wheel diameter: 19 ″ / 49 cm
-width of the rear wheel: 22 cm
-front wheel diameter: 11 ″ / 28 cm
-front wheel width: 18 cm
-recommended wheel inflation pressure: 0.6 KPa
-weight of BEACH set including transport bag: 10.5 kg
ATTENTION!
Please read these operating instructions
carefully before using the BEACH-set with the
xRover REHA:

2
EACH-set is supplied in a
set of two rear wheels with
axles, front wheel with fork
and transport bag
Placing the wheels in the bag is done by placing
one rear wheel on the bottom of the bag with the
axle facing up
The second rear wheel is placed on it with the axle down, always so that the axles hide in
the recesses at the centre of the opposite wheel
ATTENTION!
It is essential to follow this procedure so that
the axles do not damage the casing of the
second wheel!
Then we cover the rear wheels with a partition sewn into the bag and place the front wheel
with a fork on it

3
The wheel is assembled in the same way as with a normal xRover wheel. Grasp the inner ring
of the wheel firmly with your fingers and press the black button in the middle of the wheel with
your thumbs.
At the end of the axle, you can see the balls locking the wheel on the xRover. Insert the axle into
the axle hole as far as it will go and release the black knob. By pulling on the wheel, we make
sure that it sits firmly on the wheelchair. We proceed in the same way when deploying the
second wheel. The wheels are dismantled in the reverse order.
ATTENTION!
We never put on a BEACH-set with a person sitting in
xRover! Accident may result in possible overturning of
the cart
Now we put on the front wheel with a fork.
Release the flaps on the front axle and insert the fork inside, as in the case of mounting a 14 ″
jogging wheel.
ATTENTION!
The screw must fit exactly into the
cut-out in the sleeve, otherwise the
sleeve will be damaged and the front
axle will be damaged!
Thus, the fork is inserted into the sleeve with a locking screw on
the fork mandrel pointing upwards.
Insert the fork as far as it will go and
tighten the flaps on the sleeve firmly.
The Xrover with BEACH set is now ready for use.
Disassemble the fork in reverse order.

4
The BEACH-set is intended as an accessory to xRover carts, and is used to transport people
sitting in xRover exclusively on beaches and in desert sand.
ATTENTION!
Do not use in an environment where there are sharp stones (such as
lava), metal fragments, nails, thorns, or other objects that could
damage the wheel casings!
The maintenance of the BEACH set is simple. It is performed under running water using
common non-abrasive cleaning agents. Never use thinner, benzine, toluene or other chemicals
for cleaning. Wheel oil or equivalent can be used to lubricate the wheel axles.
ATTENTION!
Do not expose to temperatures above 90 degrees. Celsius. Do not dry
on radiators, heaters, stoves or hot air guns
We wish you a lot of great experiences with xRover
by the sea and on the desert dunes!
ATTENTION!
When using the BEACH set, the brakes are not in operation! Always
park the xRover with the Beach set so that it cannot start on its own!