VOO evasion User manual

Operating instructions
The remote control
1/2
1On/off of the .évasion box
2Red LED indicator
3Recording the current programme or
aprogramme selected via the guide
4Pausing or resuming the programme
5Fast forward
6Programme guide
7Programme information
8Switching back to the previous channel
Press and hold for fast channel change
Navigation to the top of menu
9Opening the action menu
Validation of a desired action
10 Navigating right
11 Switching to the next channel
Press and hold for fast channel change
Navigation to the bottom of the menu
12 Displaying the different menus available
13 Disabling the sound
14 Turning up the volume
15 Digits 0 to 9
16 Direct link to Be tv
17 The on demand programmes of the
activeTV channel (red button)
18 Turning down the volume
19 Back to the previous step
20 Navigating left
21 Programmes available on demand
22 Back to the TV channels
23 Rewind
24 Stopping the programme
25 Switching the television on and off and
changing the television source (when the
remote control is paired with the television)
getting to know your remote control
The diagram below describes each of the buttons on your remote control. Functions may vary according to the different
services. Please refer to the operating instructions of your box for descriptions of specic functions.
installing the batteries
Two AAA alkaline batteries are needed to operate the remote control. These batteries are already installed with a
protective lm to prevent the batteries from discharging too quickly. On the back of the remote control, remove the
protective lm protruding from the battery compartment to activate the remote control.
programming the remote control
The remote control will automatically operate in IR (infrared), which means that the remote control must be aimed directly
at the box up to a distance of 5 metres. The remote control can also operate in RF (radio frequency). This means that it
does not need to be aimed directly at the box.
Refer to the operating instructions of the .évasion box to pair your remote control with the television set, allowing you to
use a single remote to control your television set and your box.
25 1
3
5
7
10
8
11
12
14
15
16
21
4
13
9
24
23
22
20
19
18
17
2
6

Operating instructions The remote control
2/2
automatic RF pairing
After inserting the batteries, put your box in ‘pairing mode’ by pressing the
remote control pairing button on the back of your box (remote pairing).
Then press ok on the remote control, which must be close to the box
(maximum 5 metres). The remote control will go into pairing mode. If the pairing
is successful, the LED ashes 3 times.
If the pairing fails, the LED ashes 5 times and you have to restart the pairing
process described above.
If after that, the remote control is still not paired with your box, the automatic
pairing remains active as long as you have not pressed a button 25 times
inarow.
To reactivate the RF automatic pairing, you have to reboot the remote control
byremoving the batteries, reinserting them and repeating the procedure.
LED
OK
manual RF pairing
Simultaneously press the red button and the be tv button for at
least 3 seconds. After 3 seconds, the LED will ash 3 times and then
stay on. Release the buttons.
Press the keys in the following order: VOL- / MUTE / VOL +.
TheLED turns off when the button is pressed and lights up when the
button is released. If no button is pressed within 20 seconds, the LED
ashes 5 times and the remote exits the RF pairing mode.
Once the RF pairing has been carried out, the LED on the remote
control ashes 3 times. The LED will turn off and the remote control
isin RF mode.
If the pairing is not successful, the LED ashes 5 times.
The remote control returns to its previous state, that is to say either
infrared mode or paired with the previous box.
red
button Be TV
button
VOL and
MUTE buttons
battery safety
This product contains disposable batteries. Please read the following warning, the instructions on battery safety and the
battery recycling instructions.
WARNING: There is a danger of explosion if the battery is handled carelessly or incorrectly replaced. Replace only
with the same type of battery. Do not disassemble or attempt to recharge it outside the system. Do not crush or puncture
the battery or dispose of it in re or short circuit it with external contacts and do not expose it to water or other liquids.
Dispose of the battery according to local regulations and instructions from your service provider.
battery safety
- Insert the batteries correctly. There may be a risk of explosion if the batteries are inserted incorrectly.
- Do not attempt to recharge ‘disposable’ or ‘non-reusable’ batteries.
- Please follow the instructions for charging rechargeable batteries.
- Replace the batteries with the same or equivalent type.
- Do not expose batteries to excessive heat (such as sunlight or re).
- Do not expose the battery to temperatures above 100°C (212°F).
battery recycling
- Bring your old device to a VOO point of sale or a recycling centre.
- The batteries may contain substances that could be harmful to the environment.
By recycling with Recupel and Bebat, you contribute to a cleaner world.
www.recupel.be
www.bebat.be
Find the answers to all the questions related to the .évasion remote control in the FAQ on our website
www.vooassistance.be or contact us on 078 50 50 50, our technical specialists will be happy to help you.