Philips SRP2018/27 User manual

SRP2018
Always there to help you
Register your product and get support at
www.philips.com/support
User manual
Question?
Contact
Philips

English
EN 1
Contents
1 Your universal remote 2
Introduction 2
Overview of the universal remote 2
Supported devices 3
2 Get started 4
Insert batteries (not included) 4
Set up the universal remote 5
3 Notice 9
Disposal of your old product and battery 9
4 Service and support 10
Frequently asked questions 10
Need help? 10
Contents

2 EN
1 Your universal remote
Congratulations on your purchase, and welcome to Philips!To fully
benet from the support that Philips offers, register your product at
www.philips.com/welcome
Introduction
With the universal remote, you can operate up to 8 different devices.
Overview of the universal remote
a
b
c
d
e
f
g
a INPUT: select available source inputs (antenna, cable, etc.).
: LED indicator
: power on or off.
b Device selection buttons

English
EN 3
c GUIDE: displays the program guide.
INFO: displays on-screen channel information.
MENU: menu on or off.
BACK: exit from the menu.
OK: conrm your selection.
/ / / : up/down/left/right.
d VOL+/-: adjust the volume.
CH+/CH-: go to the next/previous channel.
: mute
LAST: return to the previous tuned channel.
e : previous page
: stop
: next page
: play
: pause
: rewind
: record
: fast forward
f A/B/C/D: context sensitivity buttons (A - yellow, B - blue, C- red,
D - Green)
g Digit buttons
ENTER: conrm the digit button selection.
(-): select between one and two-gure channel numbers.
Supported devices
Device name Description
TV/TV-2 TV, DTV
CBL/SAT Cable box, satellite receiver, IPTV, DVR, HDTV
decoder and TiVo
BD DVD player/recorder, Blu-ray player
STR Streaming devices, Apple TV, Roku, Sony,WD TV,
Netgear
VCR Video cassette player/ recorder
AUX Auxiliary equipment, media center PC, others

4 EN
2 Get started
Insert batteries (not included)
Warning
• Check the battery polarity when inserting in the battery compartment. Incorrect
polarity may damage the product.
Caution
• Risk of explosion! Keep batteries away from heat, sunshine or re. Never discard
batteries in re.
• Risk of decreased battery life! Never mix different brands or types of batteries.
Note
• When you replace the batteries, all user settings will be retained in the memory of
the universal remote for 5 minutes.

English
EN 5
Set up the universal remote
You must rst set up the universal remote before operating your
devices.
Manual registration
1 Switch on your device.
2 Press and hold the device selection button (e.g.TV) for 5 seconds
until the red LED is on.
3 Look up the 5-digit code for your brand in the code list. Codes
are listed by the device type and brand name.The most popular
code is listed rst.

6 EN
4 Enter the rst 5-digit code using the digit buttons.
5 If the light is off, a valid code is saved. Otherwise, the light will ash
once, and then remains on for code re-entry.
6 Operate the device with the universal remote. If your device
responds correctly, it means you have entered the right code.
Otherwise, repeat from step 2, and enter the second code on the
list.
Note
• It is possible sometimes that your device only responds to some of the buttons. In
such case, set up with the next code in the code list, and try operating your device
again.
• Each device button can be used to set up any device. E.g. you may setup aTV using
the BD device button.

English
EN 7
Auto registration
1 Switch on your device.
2 Press and hold the device selection button (e.g.TV) for 5 seconds
until the red LED is on.
3 Point at your device with the universal remote.Then press and
release to start searching the code for your brand. A different
infrared signal is sent every 2 seconds as the universal remote
searches, indicated by a red ash.

8 EN
4 When the device is off, immediately press and release OK to save
the code.The red LED indicator will turn off.
max. 20
minutes
5 Operate the device with the universal remote. If your device
responds correctly, it means you have saved the right code.
Note
• Auto registration can be reversed, by pressing and releasing once more during the
auto registration process.This is helpful if you missed out the chance to press OK
within 2 seconds. Make sure that the device is rst powered on again.
• Repeat the same procedures to set up other devices.
• It is possible sometimes that your device only responds to some of the buttons. In
such case, set up with the next code in the code list, and try operating your device
again.