VooDoo HYHB-0101 User manual

hydraulic handbrake
INSTALLATION INSTRUCTIONS:
Part Number:
hyhb-0101
hyhb-0102
hyhb-0103
hyhb-0104

We recommend that installation of all Voodoo13 parts be completed by a professional
who is experienced in suspension tuning. With proper installation and maintenance,
Voodoo13 suspension products will provide exceptional performance and durability. For
any questions, please contact Voodoo13 immediately. We thank you for choosing
Voodoo13 for your suspension tuning needs!
NEED HELP?
Our representatives are here to help you with any questions concerning the operation of
this product. CALL 480-889-0812
Monday thru Friday 8:30am to 5:30pm MST
PART BREAKDOWN
HARDWARE INCLUDED
QTY
DESCRIPTION
2
BUTTON HEAD CAP SCREW, 5/16"-18 X 1-1/8
1
CLEVIS PIN 5/16" OD, 1-1/4"
12
FLAT HEAD #10-24 X 7/16
5
SOCKET HEAD CAP SCREW #10-24 X 5/8
1
SOCKET HEAD CAP SCREW 5/16"-18 X 2-1/2"
3
NYLON INSET LOCK NUT

INSTALLATION PROCEDURE
IMPORTANT! PLEASE READ BEFORE ATTEMPTING INSTALLATION!
The base plate and side plates are shipped assembled with the mounting
hardware hand tight. It is extremely important that during installation you back all
hardware out several turns so that during assembly it makes everything easier to line
up. Once assembled into your preferred configuration, you may tighten the hardware
completely.
Step 1: Refer to the diagrams and choose the preferred setup of your choice. Three
ways our kit can be used: The handbrake can be configured for a pullback function
either with the master cylinder facing forward or backwards. The handbrake can also
be used in a pull up function. In all three configurations, leverage can be adjusted to
effect the amount of throw required to lock up the rear wheels. Each configuration has
two levels of adjustment.
Step 2: View the diagram below on how to route the brake lines correctly. You can
either tap into the existing front lines for hydraulic fluid or run an external reservoir.
Then route that line into the inlet of the master cylinder on the hydraulic handbrake.
From there route a new line from the outlet of the hydraulic handbrake's master cylinder
to the rear brake lines. Ensure to bleed the brakes after installation before driving on a
public road.

WARRANTY
All products sold are subject to the following warranty:
Voodoo13 offers a Limited Lifetime Warranty for our products to the original retail
consumer against defects and workmanship when used on light truck and car
applications under normal operating conditions. This warranty does not apply to parts
that have been improperly installed or wearable items such as, but not limited to, worn
bushings or bearings unless proven to be defective from the manufacturer.
Exterior finish on all Voodoo13 products is not considered a valid warranty; consumers
are responsible for the maintenance of paint, anodize or raw metal finish.
The consumer will be responsible for the removal and freight costs both to and from the
Distributor from which the product was originally purchased. Proof of purchase and
product registration through the Voodoo13 website is mandatory in order to receive
warrantee replacement; original invoice from the Distributor from which the product was
purchased must accompany the product in question for warrantee.
Voodoo13 has the right to refuse a warrantee claim if procedures are not met by the
original consumer. All returns must have an R.M.A. approval from Voodoo13 prior to
shipping direct to the Voodoo13 facility. Exclusions from this warranty are sales outside
of the United States, the finish, dents, rust, or any condition caused by abnormal use or
neglect.
High performance parts. For off-road use only. Installation should be carried out by a qualified facility. Improper
use or installation may result in injury or death.
VOODOO13
254 W Broadway Rd,
Mesa, AZ 85210
Ph: 480.889.0812
Fax: [phone]
www.VOODOO13USA.com
WARNING