VOP SlitPrecise SP100 User manual

Slit Precise SP100 en v2 1
SlitPrecise
SP100
USER MANUAL

Slit Precise SP100 en v2 2
CONTENT
1. INTRODUCTION
2. SAFETY INSTRUCTIONS
3. DESCRIPTION OF THE UNIT
4. INSTALLATION AND INITIAL START-UP
5. PRACTICAL USE
6. TECHNICAL DATA
7. MAINTENANCE
8. SCOPE OF DELIVERY
WARRANTY
3
4
5
6
7
8
9
9

Slit Precise SP100 en v2 3
1. INTRODUCTION
Thank you for having purchased the separator for
plaster models SLITPRECISE SP100 furnace which, we are
sure will all meet all your needs and will satisfy your high
demands.
This device has been designed according to the
requirements of latest industrial standards and we
guarantee that you will use it many years as your closest
assistant.
However, inappropriate use may damage the
equipment and be harmful to personnel. Please observe
the relevant safety instructions and read the Operating
Instructions carefully.
We wish you pleasant and fruitful work with the
separator for plaster models SLITPRECISE SP100.
SYMBOLS:
This symbol indicates that there is high
dangerous tension under the bonnet which it is
put on.
This symbol indicates that the machine
complies with the requirements of the Directives
for Low Tension and Electromagnetic
Compatibility as well as for the Standards
harmonized with them.

Slit Precise SP100 en v2 4
2. SAFETY INSTRUCTIONS
The following instructions must be observed in order
to avoid personnel injury or equipment failure.
CAUTION!
the device must not be run by an operator who
is not acquainted with these instructions;
before turning on the plug in the net contact
check if the voltage in the electrical network
correspond to the working tension. In case of
discrepancy, consult a specialist;
on no account do not alter the device;
the notices and stickers must be kept in good
condition so that they are easily readable; they
should not be removed!
the machine must not function in case of being
damaged and in position to injure the staff or a
third person;
keep the cables out of heat, oil and coarse
objects; do not catch the device by the cable
when you move it.
switch off the device and pull out the plug of the
feeder cable from the contact before each
cleaning or upkeep.
spare parts which are not specified by the
manufacturer cannot be used!
keep from falling and hitting.
If the machine is used by such means not indicated by
the manufacturer, the provided protection can get worse!

Slit Precise SP100 en v2 5
3. DESCRIPTION OF THE UNIT
1. Linear laser;
2. Shield;
3. Mouthpiece for aspiration hose.
4. Right cover with sensor;
5. Left cover with sensor;
6. Knurled screw;
7. Power switch;
8. Power plug of aspiration;
9. Fuses 3,15А/250V
10. Fuse 6,3А/250V
11. Ferrite of network cable;
1
2
3
3
6
78
9
11
10
11
5
4

Slit Precise SP100 en v2 6
4. INSTALATION AND INITIAL START-UP
UNPACKING
CONNECTIONS
INSTALLATION OF THE CUTTING DICS
Carefully remove modules from packages;
Make sure that the mains voltage is ~230V and the
contact is reliably grounded.
The network power switch is located on the left side of
rear panel. There is a sign POWER below. Place the
device in a way that allows its easily switching on and
off from both the main switch and the contact.
The power feeding cable of the aspiration is plugged
into the socket with the sign 230V~/6.3A on the rear
panel;
the hose of the aspiration is plugged into the special
socket on the rear panel.
Before the installation of the cutting plate, ensure that
the network cable is unplugged from the socket.
Remove the lid of the aspirator by unwinding of the
knurled screws (position 6).
By means of a monkey wrench size 19 and hexahedral
key size 4 unwind the tightening washer, place the disk
and tighten up.

Slit Precise SP100 en v2 7
5. PRACTICAL USE
ATTENTION!
Place the plaster mould on the working surface, while
keeping it upright on both sides.
By using the laser marker, define the place of cutting on
the side opposite to the incision.
The plate shall be turned around only with two hands
placed on the respective spots on the lids of the device
where the sensors are installed.
The right position of the hands is indicated by the
respective light diodes. Moreover, it is necessary to push
the working surface downwards, in order to switch the
mechanical key on and then the motor is winding.
At the same time when the plate rotates, the electricity
power feeds the coupling, which in turn feeds the
aspiration. If it is cased-in, it will be operating only during
the time of cutting.
Push the model downwards and slowly to the working
surface in order to carry out the cutting.
If you push harder, it is possible to divert the plain of
cutting. Always switch on an aspirator hose or a vacuum-
cleaner to the device (position 3), in order to avoid
excessive dusting!

Slit Precise SP100 en v2 8
6. TECHNICAL DATA
1. Electrical supply
2. Power consumption
3. Category of overtension
4. Size of the diamond disc
5. Speed of rotation of the disc
6. Width of cut
7. Overall dimensions of closed furnace:
7.1. Width
7.2. Length
7.3. Height
8. Model Weight
9. Working temperature
10. Laser class
11. Level of environment pollution
12. The device is designed for usage in normal dental
premises up to 2000 m altitude above sea level.
13. The maximum relative humidity of the air must
be 80% for temperatures up to 31°С, decreasing
lineally to 50% relative humidity for temperature
40°С.
~230 V, ±10%, 50/60Hz
200 W
ІІ
Ф85mm X 12mm
10000 –12000 rpm
0,3 мм
300 мм
330 мм
240 мм
9,3 кg
5°С - 40°С
3А
2

Slit Precise SP100 en v2 9
7. MAINTENANCE
8. DELIVERY SCOPE
Clean only with a dry or slightly moist cloth (no solvents!).
Avoid any placement of objects on the corpus of the
device.
Change the safety locks with the announced valus only,
namely:
3,15A; slow (class T)
6,3A; slow (class T)
No repair activity by a service technician who is not
authorized by the manufacturer is allowed!
The lifting and carrying should be made only with the both
hands from below as the device stands on end.
No carrying and transportation in another state except for
vertical position is allowed!
1. Separator SР100 1 pc
2. Diamond disk 1 pc
3. Spare fuses
T 3,15А/250V 2 pc
T 6,3A/250V 1 pc
4. User manual 1 pc
PRODUCER: “VOP” Ltd.
2140 IZ ”Microelectronica”
Botevgrad, Bulgaria
Теl. 0723 66303
Теl./Fax [phone]

Slit Precise SP100 en v2 10
Serial Number __________________
Invoice number _________________
Date __________________________
______________________________________________
CLIENT:
MANAGER of “VOP” Ltd.
______________________________________________
Serial Number _____________
Invoice number __________________
Date _____________________
Voucher Manufacturer
“VOP” Ltd.
Mikroelectronika
2140 Botevgrad
Tel. [phone]
Tel./Fax [phone]
Slit Precise SP100
WARRANTY SHEET
“VOP” Ltd. warrants the consumer for proper operation of all parts and materials in this product
during a period of 12 months since the day of its purchase.
During this period VOP Ltd. or its authorized persons will repair on its own account all defects
which have occur during the normal operation of the machine.
Defects caused by improper transportation, storage and manipulation of the product or due to
malfunction of the electrical mains supply are repaired on the account of the customer.
This warranty shall become void if attempts are made to repair the product by persons not
authorized by the producer.