VOWNER JY-1222 User manual

BATHROOM MIRROR CABINET
WITH LIGHTS AND DEFOGGER
User Manual

INTRODUCTION
Thank you very much for choosing our Bathroom Mirror Cabinet with Lights and Defogger. In
order to facilitate the use of the product, please read this manual carefully before installation.
NOTE: The important safeguards and instructions that appear in this manual are not meant
to cover all possible conditions and situations that may occur. It must be understood that
common sense, caution and care, are factors that can't be built into any product. These
factors must be supplied by the person(s) caring for and operating the fixture. Do not install
this fixture in hazardous locations.
WARNINGRiskofFireandElectricShock
AllfittingsmustbeinstalledinaccordancewithcurrentIEEwiringregulations.Ifindoubt,
consultaqualifiedelectrician.
Switchofftheelectricalsupplyatthemaincircuitboardbefore installationandmainte-
nance.
Suitableforindooruseonly.Thisproductshouldbepositionedwellawayfromcurtains
andfabrics.Nevercoverthemirror.
Regularlycheckthecord,thetransformerandallotherpartsfordamage.Ifanypartis
damagedtheproductshouldnotbeused.
1.
2.
3.
4.
5.
INSTALLTION PRECAUTIONS
After opening the package, please inspect the product immediately for damage in
transit or missing parts. Please check the dimming, color mixing and defogging functions
of the mirror light before installation, and contact our customer service in time if you
have any questions.
Handle the product with care and protect against knocks to all sides and edges of the
glass. Please do not remove the transparent silicone protector before installation.
Keep the home voltages between 100V and 240 V, the best is 220V. When the home
voltage exceeds 240V, please remember to use transformer.
Adapters and plugs are provided with this product. Recommend to use the plug directly.
If you need to link wall switch, you can choose to cut off the plug and link the wire. Note:
When the plug is cut off, the product is not covered by the warranty.
Ensure there are no hidden pipes or cables in the wall before drilling.
Ensure that the fixing location is able to take the weight of the complete fitting. (solid
stone / brick walls).
Disconnect power before installing, adding or changing any component.
Installed by a qualified technician is recommended.
Wear suitable eye protection while drilling. Be careful when using power tools near water.
A minimum of two people is needed to perform this installation.
01.
02.
03.
04.
05.
06.
07.
08.
09.
10.
11.
- 01 -

When the power is on, the button lights up and turns white. Long press to light off button
when not use. The button turns and stays blue when the mirror is lit.
Short press the button to turn on/off the light. When the light is on, press consecutively to
adjust the color temperature; After staying at one color temperature for more than 3 sec-
onds, the next click will directly turn off the light.
1)
2)
Press the ON/OFF button and hold on for a few seconds to activate the dimmer function.
Finish setting by withdrawing your finger when brightness reaches the level you need.
The color temperature and brightness have a memory function, and the next time the
power is turned on automatically retains the last setting.
1)
2)
Mirror beginsto get warmanddefogafter pressing thedefogger button.Pressagain to
exit theanti-fogfunction. It takes 15 minutes for the mirror to heat up to reach a tempera-
ture that can effectively prevent water vapor from condensing on the surface of the
mirror. It is recommended that you turn it on in advance.
When you are not using it, remember to turn off the switch to prevent wasting energy.
Anti-fog function will automatically turn off after working for an hour to avoid long time
heating. During the defogging process, turning the lights on/off will reset the defogging
timer auto-off function, and automatically turn off after the next hour.
1)
2)
3)
Adapters and plugs are provided with this product. Recommend to use the plug directly.
If you need to link wall switch, you can choose to cut off the plug and link the wire. Note:
When the plug is cut off, the product is not covered by the warranty. It is recommended that
you contact an electrician to install it, or operate under the guidance of a professional.
1)
2)
- 02 -
OPERATION INSTRUCTION
1. ON/OFF/Switch-color Function
3. Anti-fog Function
4. Connect to Wall Switch
2. DimmerFunction
WARNING
WALL
LIVE(usually BLACK)
NEUTRAL(usaully WHITE)
GROUND(usually GREEN)
MIRROR

AFTERCAREINSTRUCTIONS
Clean with a soft, dry cloth only when the power is off.Do not use cleaning agents or
abrasive materials.Do not allow moisture to come in contact with the lamp.
In any case, the product can not be covered by thermal insulation pads or similar materi-
als, otherwise the product will be damaged.
Thelightsourceofthisproductisnon-changeablelightdiodes(LED).Donotdisassemble
theproduct,asthelightdiodescancausedamagetotheeyes.
1.
2.
3.
- 03 -
SPECIFICATION DATA SHEET
PARAMETER
Model No.
Color Temperature
Input Voltage
Output Voltage
Working Temperature
Life Span
Anti-fog
Safety Compliance
Mirror Glass
Switch
Mounting Method
Materials
Weight
Dimension
SPECIFICATION
JY-1222
3000K 4000K 7000K
100-240V AC
12V DC
0-40�
30000-50000 hours
Yes
FCC
3 mm
Touch Sensor Switch
Wall Mounted(Vertical Only)
Glass Mirror, Particle board,
LED strip and other electric parts
16.3 lbs
23.4×19.5×4.3 inches

4
7
15
28
6
3
A B C D E
M3x12mm
M5x30mm
F G H I J
KL M N O
x12 x12 x1 x1 set x2
x3 x16 x1 x1 x4
x4 x6 x1 x1 x6
- 04 -

1
2
Bx10 Gx2 Hx1
You will need
Ax2 Bx2
You will need
B
B
A
A
7
1
- 05 -
B
B
BB
B
B
B
B
B
B
4
5
G
G
H
B

3
4
Ax6
You will need
Ax4
You will need
4
A
A
5
3
A
A
A
A
A
A
1
5
6
7
- 06 -
6
3
A
A
7
4
6

5
6
Fx3 Gx6
You will need
Fx3 Gx8 Ix1
You will need
G
GI
8
G
F
G
F
F
F
G
G
G
F
F
F
G
G
G

7
Dx2
You will need
7
5 6
7
46

8
E
E
M
N
O
D
L
M
N
Ex2 Lx6 Mx1
Nx1 Ox6
You will need