Voxx Electronics AW18 User manual

EKEY System
AW18, AW26, & AX09
Cover Control Module Owner’s Manual (R1.00) PAGE-1
Product Description:
The EKEY system is a passive keyless entry system that allows the end user to access and Push Start the vehicle and
to remotely send commands to Lock/Unlock the Driver Door, Passenger, Cab, and Cargo using the Fob remote. It is
comprised of the following 3 products:
•AX09, Car Module with BLE. Will be powered from car battery.
•AW26 Car sensors, it has two types of BLE and NFC sensors that can be installed at interior or exterior of
the vehicle and be powered for vehicle’s battery.
•AW18 keyfob, has a BLE and NFC tag and will be powered by coin cell battery CR2450.
Figure 1 AX09 Figure 2 AW26 Figure 3 AW18

EKEY System
AW18, AW26, & AX09
Cover Control Module Owner’s Manual (R1.00) PAGE-2
EKEY System Diagram
Figure 4: EKEY System Diagram
AW18 Fob sends BLE signal to the AW26 Sensors. It can also be placed near the sensor to scan NFC.
Sensors can be installed at interior or exterior of vehicle. This is placement and installation example:
•Sensor 1 is placed near Cargo.
•Sensor 2 is placed near Passenger.
•Sensor 3 is placed near Driver.
•Sensor 4 is placed near Cab.
The sensors communicate Data Command over UART to the AX09 unit, which in turn processes the data and
forwards it over CAN to the Vehicle.
The Fob communicates over BLE to AX09 module and to sensors to provide user location and has also an NFC tag
to communicate with AX09 module through NFC reader installed on AW26 sensors.
For First time use, the Fob needs to be learnt by the system.

EKEY System
AW18, AW26, & AX09
Cover Control Module Owner’s Manual (R1.00) PAGE-3
Government Regulations
This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) This device must accept any interference received, including interference that may cause
undesirable operation.
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates and can radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television, which can be
determined by turning the equipment OFF and ON, the user is encouraged to try to correct the interference by one or more of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio / TV technician for help.
To satisfy FCC RF exposure compliance requirements, the device and its antenna must maintain a separation distance of 20 cm
or more from the person’s body, except for the hand and wrists, to satisfy RF exposure compliance.
WARNING!: Changes or modifications not expressly approved by VOXX Electronics. could avoid user's authority to operate the
equipment.
This device complies with Industry Canada license-exempt RSS-247 standards. Operation is subject to the following two
conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired operation of the device.
Cet appareil est conforme avec Industrie Canada exempts de licence standards RSS-247. Son fonctionnement est soumis aux deux
conditions suivantes:
1. Cet appareil ne doit pas provoquer d'interférences et
2. Cet appareil doit accepter toute interférence, y compris celles pouvant causer un mauvais fonctionnement de
l'appareil.”
Health Canada RF Exposure Warning:
This device complies with Health Canada’s Safety Code. The installer of this device should ensure that RF radiation is not emitted
in excess of the Heath Canada’s requirement. The device must maintain a separation distance of 20cm or more from the person’s
body, except for the hands and wrists. Information can be obtained at:
http://www.hc-sc.gc.ca/ewh-semt/pubs/radiation/radio_guide-lignes_direct/index-eng.php
Lignes Directrices de Santé Canada sur l’exposition aux radiofréquences:
Cet appareil est conforme avec Santé Canada Code de sécurité 6. Le programme d’installation de cet appareil doit s’assurer que
les rayonnements RF n’est pas émis au-delà des limites établies par Santé Canada. L’emplacement de l'appareil doit se situer à
une distance de 20cm ou plus par rapport au corps de la personne, à l’exception des mains et des poignets. Les informations
peuvent être obtenues à l’adresse Internet suivante:
http://www.hc-sc.gc.ca/ewh-semt/pubs/radiation/radio_guide-lignes_direct/index-fra.php

EKEY System
AW18, AW26, & AX09
Cover Control Module Owner’s Manual (R1.00) PAGE-4
Warranty Information
LIMITED ONE-YEAR CONSUMER WARRANTY
For a period of ONE YEAR from the date of purchase of a VOXX Electronics product, Voxx Electronics. (“Voxx”) promises to the
original purchaser, to repair or replace with a comparable reconditioned piece, the security or remote start accessory piece
(hereinafter the “Part”), which proves to be defective in workmanship or material under normal use, provided the following
conditions are met: the Part was purchased from an authorized VOXX Electronics dealer; and the Part is returned to VOXX
Electronics, postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing the following information:
consumer’s name, address, telephone number, the authorized licensed dealer’s name and complete product and Part description.
This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to its
intended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation, or other
causes not arising out of defect in materials or construction.
TO THE MAXIMUM EXTENT ALLOWED BY LAW, EXCEPT AS STATED ABOVE, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO
EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND
WARRANTY OF NONINFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND VOXX Electronics NEITHER
ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION
WITH ITS PRODUCTS. VOXX Electronics HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD
PARTIES INCLUDING DEALERS OR INSTALLERS. VOXX Electronics IS NOT OFFERING A GUARANTEE OR INSURANCE AGAINST
VANDALISM, DAMAGE, OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS, AND VOXX Electronics x HEREBY DISCLAIMS
ANY LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE, OR VANDALISM. IN THE EVENT
OF A CLAIM
OR A DISPUTE INVOLVING VOXX Electronics OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE
OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE
MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST VOXX Electronics SHALL BE STRICTLY LIMITED TO THE AUTHORIZED VOXX
Electronics DEALER’S PURCHASE PRICE OF THE PART. VOXX Electronics SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES
WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE
LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING
THE ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR AT VOXX ’S OPTION THE PART AS
DESCRIBED ABOVE.
This warranty only covers Parts sold within the United States of America and Canada. Parts sold outside of the United States of
America or Canada are sold “AS-IS” and shall have NO WARRANTY, express or implied. Some states do not allow limitations on
how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives
you specific legal rights and you may also have other rights that vary from State to State. VOXX Electronics does not and has not
authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part. For
further details relating to warranty information of VOXX Electronics products, please visit the support section of VOXX’s website.
THE WARRANTY IS VOID IF:
1. The product has been damaged, altered in any way or tampered with, without the explicit written consent
of our certified technician.
2. The product is damaged due to accident, fire, flood, shipping and handling, misuse, neglect, or other
conditions beyond the control of VOXX Electronics.
3. The product has been installed or repaired by anyone other than a certified technician.
4. The product has been improperly installed or used.
THE WARRANTY DOES NOT COVER:
1. Scratched or worn 8812 module case.
2. Installation and/or removal charges for DS4WS module and accessories.
3. Shipping and handling charges incurred for product exchange or replacement.
4. Any material damage other than to the product itself.
5. Harnessing, LED lights, switches, relays, etc.

FCC Statement
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate
the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
To comply with RF exposure requirements, a minimum separation distance of 20mm must be maintained between the user’s body and
the handset, including the antenna.
IC STATEMENT
This device complies with Industry Canada licence-exempt RSS standard(s)
Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may cause undesired
operation of the device.
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. End user must follow the specific operating instructions for satisfying RF
exposure compliance. This transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter.
Ce dispositif est conforme aux normes autoriser-exemptes du Canada RSS d'industrie
L'exploitation est autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.Cet équipement
est conforme avec l'exposition aux radiations IC définies pour un environnement
non contrôlé. L'utilisateur final doit respecter les instructions de fonctionnement spécifiques pour satisfaire la conformitéaux
expositions RF.