Voyager ROVER E-SCOOTER User manual

USER’s MANUAL
ITEM NUMBER I SCOT-1030R
Rover E-Scooter

1
SAFETY PRECAUTIONS
When using your Voyager Rover E-Scooter, basic safety precautions should always
be followed, including the following:
BEFORE RIDING
1. READ ALL INSTRUCTIONS BEFORE USING YOUR SCOOTER.
2. Your scooter is designed to be used by adults, 14 and older.
3. Do not ride scooter in temperatures below 30ºF.
4. Do not let children use your scooter.
5. Never immerse the scooter in water.
6. Do not leave the scooter in high temperatures.
7. Make sure to wear a helmet and any other protective gear necessary to ride a
scooter, making sure to comply with the laws of your local municipality.
8. Do not ride your scooter with any loose clothing that can get caught in the
wheels.
9. Do not expose your scooter’s battery to liquid or moisture. Similarly, do not
expose your scooter or its battery to excessive heat or fire.
10. When charging the battery, only use the supplied charging cable included
with your scooter.
12. Connect all wires properly, making sure they are not entangled.
13. Do not ride your scooter if you notice any defects or irregularities. Contact the
manufacturer or a certified technician immediately for support.
WHILE RIDING
1. When riding your scooter, make sure to always follow all traffic and safety rules
based on the laws of your local municipality.
2. Do not ride your scooter while under the influence of any medication which can
cause impairment.
3. Do not attempt to do any tricks while riding your scooter. Furthermore, do not
ride your scooter over rough terrain, icy roads, or uneven surfaces.
4. Ride carefully. Avoid applying the breaks abruptly.
5. Practice riding in spacious areas at low speeds until you become more
experienced and comfortable with higher speeds.
6. Do not allow your scooter to be dragged by cars or bikes. Do not use your
scooters on escalators or in crowded areas.
7. Do not use your scooter at night or in areas of low visibility.
8. Always power off your scooter when it is not in use.
9. Never allow more than one person on the scooter at a time.
10. Do not ride scooter near stairs or bodies of water.
NOTE: The color and design of your scooter may vary from the ones displayed in
this user’s manual.

2
INTRODUCTION
SPECIFICATIONS
Thank you for purchasing your new Voyager Rover E-Scooter and welcome to the Voyager
family. We hope that you’ll do plenty of exploring on your new scooter. Please enjoy your
new scooter responsibly and be sure to read the entire instruction manual before your first
use. Have a blast, be safe and Get Moving!
• Battery Type: Rechargeable 18650 Lithium Battery
• Battery Capacity: 36V/8.7AH
• Motor Power: 250W
• Motor Type: Brushless Gearless Motor
• Material: 6061 aviation aluminum
• Max Mileage: 12.5 miles
• Waterproof IPX4
• Charger: 110-240V; 50-60Hz
• Charge Time: ~3-5 Hours
• Net Weight: 26 Pounds
• Max Rider Capacity: 220 Pounds
• Recommended For Ages: 14+

3
YOUR SCOOTER
Silicone Grip
Electromagnetic
Brake
LCD Display
Throttle
Front Light
Charger Port
Inflatable
Front Wheel
Assist-pulling
Wheel
Kickstand Brushless Motor
Brake Pedal
Anti-slip Riding Platform
Bluetooth Speaker
Foldable Joint

4
LCD display
Brake Error
Pole Pair
Undervoltage Reminder
Setting
Revolving Speed
Power Display
Speed Gear
Single Trip Mileage
Wheel Diameter
Motor Error
Controller Error
Throttle Error
Speed
Mile
Kilometer
Time Display
Single Trip Mileage Total Mileage
Power/Function Switch-
Gear Up-
Gear Down-
-Hold down the to turn on/off the power.
-Press quickly the to switch the LCD display
to different parameters.
-Press the or to switch the speed gears.
There are 3 speed gears: First gear=6mph
Second gear=9mph
Third gear=13mph

AsSEMBLY
Step 1: Open the package and take
the scooter and its parts.
Step 2: Pull down the clip to
unlock the buckle lock, then
unfold the e-scooter body.
Step 3: After unfolding the scooter,
pull up the buckle and put it into
the groove between the two
speakers to lock it.
5

6
Assembly Cont’d
Step 1: Align the bottom of the
handlebar to the scooter body.
Step 2: Lock the handlebar
with the screw and the
screw driver in the toolkit,
then plug the screw hole
with the rubber plug.
Step 3: Connect the cables that
come out from the scooter body
with the cables from the handlebar.
Installing the Handlebar:

7
Folding & Dragging
Step 1: Pull out the buckle and unlock
the buckle lock.
Step 2: Fold the scooter
body downward.
Step 3: Folded scooter.
Carry the handlebar of the
E-scooter, then you can drag it.
Portability

using the scooter
8
Throttle: On the right handlebar is the throttle
apparatus. Press it to speed up the scooter.
Brakes: On the left handlebar is the brake. Press it
to stop the scooter. For a sudden stop, while
pressing the handlebar brake, also press
the rear foot brake.
Cruise Control: Ride the e-scooter at a constant speed for more than six
seconds to enter cruise mode. No need to press the throttle button,
the scooter will stay at current riding speed. If you press the throttle or brake
the scooter will exit cruise mode.
Bluetooth Speaker
Connecting the Bluetooth speaker: Turn on the
Bluetooth of your mobile device. Open the
Bluetooth manager and find the “E-scooter.”

Riding the scooter
9
Step 1: Press the power button to power on.
Step 2: Make sure the clip
is folded and locked
into place.
Step 3: Hold the handlebar with both hands
and put one foot on the board. Use your
other foot to push off and start the scooter.
Step 4: Place both feet on the
board while it speeds up to
keep stable while riding.