VS Sassoon The Rugged Commander Lithium All-In-One User manual

1
TOOL TIPS
for the rechargeable lithium all-in-one
that’s built tough.
VSM7275RA
RUGGED
COMMANDER
THE
Lithium All-In-One

2
HEY YOU!
TAKE A BOW FINE SIR.
THINGS ARE LOOKING UP
& YOU’VE JUST MADE A
QUALITY PURCHASE
WITH THIS NEW GROOMING TOOL.
WE KNOW YOU’VE GOT THIS, BUT BEFORE YOU JUMP INTO
USING YOUR NEW SIDE KICK, HERE’S A FEW TIPS & TRICKS
TO KNOW BEFORE LETTING YOUR CREATIVITY RUN LOOSE.
HIT UP VSFORMEN.COM.AU FOR MORE GROOMING & INSPIRATION.

THE RUGGED COMMANDER / TOOL TIPS
3

THE RUGGED COMMANDER / TOOL TIPS
4
IMPORTANT SAFETY
INSTRUCTIONS
When using electrical appliances, especially when children are present, basic
safety instructions should always be followed, including the following:
Polythene bags over product or package may be dangerous. To avoid danger of
suffocation, keep this wrapper away from babies and children. This bag is not
a toy.
DANGER: When the unit is used in a bathroom, unplug it after use
since the proximity of water presents a hazard even when the
appliance is switched off
WARNING: Do not use or leave the AC power adaptor in a position where it
can become wet or there is a danger of it falling into a basin or other vessels
containing water. Keep the appliance dry, unless it otherwise specified. Do
not use this appliance in or near bathtubs, showers, basins or other vessels
containing water.
- Do not immerse appliance in water or other liquids.
- Do not reach for an appliance that has fallen into water.
- Take care to avoid contact between the moving blades of the unit and the
skin, paying particular attention to the face, neck and hands.
- This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
- Children should be supervised to ensure that they do not play with the
appliance.

THE RUGGED COMMANDER / TOOL TIPS
5
IMPORTANT: Always unplug the appliance when not in use or before cleaning.
Do not leave unattended when plugged in or switched on. Do not place on any
heat sensitive surface.
- Do not use any attachments other than those supplied by Conair Australia
Pty Ltd.
- Use this appliance only for its intended use as described within this
instruction booklet.
- Always unplug the appliance when fully charged.
- This appliance is not intended for commercial use.
- Never drop or insert any object into an opening.
- Do not use the appliance with damaged or broken attachment combs or with
any teeth missing from the blades, as injury may occur.
- Do not place on any surface while it is operating.
- Keep the cord away from heated surfaces
- Never twist or pull on the power cord.
- Do not use an extension cord with this appliance.
- After use do not wrap the cord around the appliance as in time this may cause
the cord to fracture. Coil cord loosely by the side of the appliance in storage.
- Do not use outdoors or operate where aerosol (spray) products are being
used or where oxygen is being administered.
- Do not use the appliance if it is damaged. In the event of damage, discontinue
use immediately and contact your dealer for instructions on returning it for
examination or exchange. If the supply cord is damaged, it must be replaced
by the manufacturer, its service agent or similarly qualified person in order
to avoid a hazard.
- Always ensure that the voltage to be used corresponds to the voltage marked
on the unit.
- For additional protection, the installation of a residual current device
(RCD) with a rated operating current not exceeding 30mA is advisable in
the electrical current circuit supplying the bathroom. Ask your installer for
advice.

66
1. Li-ion powered for cordless use
2. 30mm wide multi-use stainless
steel blade for beard, stubble,
moustache, goatee & body
zones
3. High performance motor
4. 3 Stubble Comb Guides
(close, medium & high)
5. 3 Jaw Line Comb Guides
(1mm, 2mm & 3 mm)
6. Rotary trimmer for nose & ears
7. 5 position comb guide (4mm
to 14mm) for tackling short or
longer length beards, goatee
and body zones
8. Storage stand
9. World wide voltage power
adaptor automatically adjust
between 100- 240V power
supplies
10. Cleaning brush
11. Oil
THE RUGGED COMMANDER
BRAVO. YOU’VE MADE A QUALITY PURCHASE.
The Rugged Commander is the rechargeable lithium all-in-one trimmer
that’s built tough.
2
1
8
10 1110
46 5 7
9
3
THE RUGGED COMMANDER / TOOL TIPS

THE RUGGED COMMANDER / TOOL TIPS
7
PREPPING YOUR
NEW TOOL
CHARGING
The The Rugged Commander is so easy to use. But before you start using your
new tool, you must take the time to charge it overnight for 3 hours before its
first use. Your new tool comes with a small amount of charge, but the initial
charge will ensure your new tool will have optimum power performance to give
you smooth fast cutting, every time.
- Before using for the first time, fully charge your new tool continuously for
3 hours.
- Maximum battery capacity will only be reached after 3 charging &
discharging cycles.
- Ensure your new tool is switched off.
- Insert the small plug on the charging adaptor into the socket on the bottom
of your new tool.
- During charging, the indicator will flash continuously until the battery is full
charged. Then the charging indicator will stop flashing but remain on to show
trimmer is charged.
- When the trimmer is about to run out of energy,the charging indicator will
flash to indicate that you have less than 15% battery capacity remaining.
- A full charge will supply 60 minutes cordless runtime.
- To maintain optimum capacity of the rechargeable battery, it is highly
recommended to fully discharge & then recharge your tool for 3 hours every
6 months.
WARNING: If the charging light suddenly starts to flash rapidly(more than
3 flashes per second).the appliance is faulty.If this happens,please stop
charging and remove the adapter from the outlet and contact our customer care
center for further advice.

THE RUGGED COMMANDER / TOOL TIPS
8
HOW TO USE THE
RUGGED COMMANDER
BEFORE USING
• Always inspect the trimmer blades for noticeable signs of damage.
• Always inspect the trimmer blades before use to ensure they are free from
hair, debris etc.
• Ensure the trimmer is sufficiently charged before use.
• For best performance use on clean, dry hair that has been combed until
tangle-free.
OILING THE BLADES
To get the sharpest, most precise cut, it is highly recommended to oil the blades
about once a month.
Using the oil supplied with your new tool, unscrew the cap & cut off the very end
of the plastic tube with a pair of scissors to release the oil.
Switch your tool on, gently squeeze the oil tube & apply 2 drops of oil onto the
blades. Leave the tool on for a further few seconds to allow the oil to thoroughly
spread across each of the blades. Switch off the tool & remove any excess oil by
gently dabbing with a cloth.

THE RUGGED COMMANDER / TOOL TIPS
9
HOW TO CHANGE THE TRIMMER HEAD
• The trimmer’s upper blade can be removed to use the single detailing blade as
shown in Fig. 1 and Fig. 2.
NOTE: All attachments combs also fit on the single detailing blade for single
blade trimming.
• To re-attach upper blade see Fig. 3 and Fig.4.
Step 4
Insert the white tab,
slide forward until
the 2 front tabs drop
in and the blade
snaps in place.
Step 1
Push the upper
blade forward.
Step 3
Line up white tab
with opening in
lower blade.
Step 2
Lift the
blade off.
Fig.1 Fig.2
Fig.3 Fig.4

THE RUGGED COMMANDER / TOOL TIPS
10
TRIMMING TIPS
Hit up www.vsformen.com.au for more grooming tips & inspiration.
USING THE BLADE TO OUTLINE
• Do not attach a comb guide.
• Hold the trimmer upside down with the blade facing downwards, yet flat
against the skin.
• Move the trimmer gently downwards in small strokes around the edge of the
area you wish to outline.
• Having defined the outline, hold the trimmer with the blades pointing
upwards, yet flat against the skin and move the trimmer upwards against
the direction of hair growth. This will trim the unwanted hair adjacent to the
outline.
BE CAREFUL NOT TO APPLY EXCESS PRESSURE
TO THE BLADE, AS THIS MAY DAMAGE THE BLADE
AND CAN RESULT IN INJURY TO THE SKIN DURING
TRIMMING

THE RUGGED COMMANDER / TOOL TIPS
11
USING THE STUBBLE AND JAW COMB GUIDES
This trimmer includes 3 stubble combs designed to achieve the perfect stubble
look. It also includes 3 jaw combs that will help you to achieve a neat, finished
trim under your chin. To use one of the attachments, press it down over the
trimmer blades until it clicks into position. These combs allow you to achieve 6
different looks to your already existing growth.
Each comb has a different length – please see below table for an overview of
the combs.
Customise a different look each day!
S1 S1 Close stubble look
S2 S2 Medium stubble look
S3 S3 High stubble look
J2 J1 1mm trim
J2 J2 2mm trim
J3 J3 3mm trim
5-POSITION COMB 4mm, 6.5mm, 9mm,
11.5mm & 14mm trims
USING THE 5 POSITION COMB GUIDE
• To attach the 5 position comb guide, slide the comb guide onto the front of the
trimming blade and push down at the rear to lock into place – you will hear a
clicking noise when it’s in position.
• The comb guide has 5 length settings, 4mm, 6.5mm, 9mm, 11.5mm & 14mm.
To adjust the cutting length, push the button and click the comb guide
forward to the required position.
• Select the required cutting length setting (4-14 mm). If you require more than
one cutting length, start with the longest length first.
• Comb through your beard against the grain before trimming to detangle and
make the hair easy for trimming.
• Switch the trimmer on.

THE RUGGED COMMANDER / TOOL TIPS
12
• Hold the trimmer with the teeth of the trimmer pointing upwards, yet flat
against the skin.
• Move the trimmer upwards and outward through the hair, against the
direction of hair growth.
• Never switch the appliance off whilst in the hair.
• To remove the 5 position comb guide, gently lift the guide off the head by
lifting the rear section.
TRIMMING YOUR NECKLINE
• Attach the Jaw Comb guide with your desired length.
• Hold the trimmer’ with the teeth of the trimmer pointing
upwards, yet flat against the skin.
• Move the trimmer’ upward and outward through the hair, against
the direction of hair growth.
• The trimmer’ will work most efficiently when cutting through hair at its own
speed. Never force the trimmer.
• Never switch the appliance off whilst in the hair.
TRIMMING YOUR SIDEBURNS
• Attach the Stubble comb guide with your desired length.
• Always trim your sideburns from the top down.
TRIMMING & OUTLINING STUBBLE/BEARD
• Attach the 5 position comb guide and select the desired cutting
length setting.
• After you have combed through your beard in the direction it
grows naturally, you will want to outline the desired shape,
beginning under your jawline.
• Begin defining your beard’s shape under your chin and work upward on each
side of your face toward your ears. Then define the upper outline of your
beard across your cheeks, past your sideburns and towards your hairline.

THE RUGGED COMMANDER / TOOL TIPS
13
USING THE ROTARY BLADE
The rotary blade has been designed for trimming those hard to reach places like
nose & ear hair.
1. Attach the rotary trimming blade as per Fig 1.
2. Switch the trimmer on.
3. Insert the trimmer into the nose or ear and gently move the trimmer in a
circular motion.
4. Always turn the trimmer on BEFORE you insert into your nostril or ear canal to
avoid painfully snagging hairs.
5. Never insert the trimmer more than 5-6mm into your nose or ears.
6. Never turn the trimmer off whilst in the nose and ears.
Fig 1

THE RUGGED COMMANDER / TOOL TIPS
14
TRIMMER CLEANING &
MAINTENANCE
Because the trimmer blades are precision made for a very special use, they
should always be handled with care. To ensure long-lasting performance of your
trimmer, it is important to clean the blades + the comb guides after every use.
After each use, clean the trimmer blade set as follows:
1. Switch the trimmer off or unplug from the power outlet if it is charging.
2. Remove the blade set from the trimmer by placing your thumb against the
smaller cutter and pushing forward, releasing the blade set from the trimmer
housing.
3. Using the cleaning brush, gently brush and blow any hairs from the blade set
and head of your trimmer.
4. To replace the blade set, place your thumb on the large blade and snap into
place.
5. Do not disassemble the blades for cleaning.
6. After replacing the blade set, always remember to oil the blades of your
trimmer.
7. This trimmer is not waterproof . The blades can be removed and rinsed under
water.

THE RUGGED COMMANDER / TOOL TIPS
15
WORLDWIDE VOLTAGE
This appliance has a multi voltage feature for worldwide use. The voltage
automatically converts for ease of use from 100v - 240v. This appliance has
an automatic internal converter which will automatically convert the voltage
without the need of a switch. A suitable plug adaptor will be required, please
refer to the chart below.
Plug adaptor
required
Voltage and
plug adaptors
Country Voltage
setting
British plug:
240V
Ireland, Great Britain, Singapore, South America,
Hong Kong (parts only), Africa (parts only)
240V
European plug:
240V
Asia, Europe, Middle East Noumea, Scandinavia,
South America, Hong Kong (parts only)
240V
Australian and
New Zealand
plug: 240V
Australia, New Zealand 240V
American
plugs: 120V
North America, Japan, Canada
(parts of)
120V

THE RUGGED COMMANDER / TOOL TIPS
16
BATTERY DISPOSAL
The Rugged Commander contains a Li-ion battery. To protect the environment,
the appliance must be disposed of safely at the end of its useful life.
Please take the appliance to a recycling centre, where the internal
rechargeable battery should be removed by a professional and
recycled separately.
For more information about the recycling of electrical and battery operated
appliances, please contact your local council office or your household waste
disposal service.
LI-ION

THE RUGGED COMMANDER / TOOL TIPS
17
LIMITED TWO
YEAR WARRANTY
Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure
and for compensation for any other reasonably foreseeable loss or damage. You
are also entitled to have the goods repaired or replaced if the goods fail to be
of acceptable quality and the failure does not amount to a major failure. In New
Zealand our goods come with a guarantee that cannot be excluded under the
Consumer Guarantee Act 1993.
Conair Australia Pty Ltd. will repair or replace (at our option) your appliance free
of charge for twenty-four months from the date of purchase if the appliance is
defective in workmanship or materials.
This warranty is an additional benefit and does not affect your legal rights. To
obtain service under this warranty, please read the Warranty Leaflet included or
contact Conair Customer Service at [e-mail].
TO MAKE A WARRANTY CLAIM YOU MUST
RETAIN YOUR PROOF OF PURCHASE.

THE RUGGED COMMANDER / TOOL TIPS
18

Vidal Sassoon and related logos are trademarks of
The Procter & Gamble Company used under license by Conair.
©2020 Conair Australia Pty. Ltd.
Suite 101, 18 Rodborough Rd
Frenchs Forest NSW 2086
Australia
Conair New Zealand Limited
PO BOX 251159
Pakuranga, Auckland 1706
New Zealand
CONTACT US
For advice & tips on your new VS product email us on:
aus_inf[email protected]
CUSTOMER SERVICE
Australia: 1800 650 263
New Zealand: 0800 266 247
Visit VSFORMEN.COM.AU for grooming tips & inspiration.

THE RUGGED COMMANDER / TOOL TIPS
20
YOU WERE
BORN TO
BE REAL,
NOT TO BE
PERFECT
IB-19/652