VS Vereinigte Spezialmöbelfabriken 30110-30113 User manual

3
VS Vereinigte Spezialmöbelfabriken GmbH & Co.KG
Hochhäuser Straße 8 · 97941 Tauberbischofsheim · Tel.: [phone] · [email protected]
http://links.vs-service.com/downloads/71-1006_V04_DEENFR_Lounge-HiBack-115903.pdf
ASSEMBLY INSTRUCTIONS: 71-1006 V04 000721
Serie Lounge, Serie Lounge HiBack.
30110-30113, 30120-30133.
Intended use:
This seating element has been designed exclusively for use in
commercial environments and is therefore intended solely for
this purpose. Any other use that goes beyond the intended
purpose (e.g. in workshops, storage areas or damp locations)
is classed as not in accordance with the intended use. The
company VS Vereinigte Spezialmöbelfabriken GmbH&Co.KG
shall not be held liable for damage arising from such non-
intended use.
General note on reading and storing the
instructions:
Please read these instructions and in particular the notes on
safety carefully and in full before using the products. Keep
the instructions in a safe place for subsequent reference and
pass them on to other users.
General note on safety:
We use the following symbols and notes in our
assembly instructions:
Important! This symbol refers to
an important note on assembly.
On the internet:
Alternatively, they can be downloaded: (see header title).
Standardize:
Tested according to DIN EN 16139.
Scope of delivery:
The product is delivered fully assembled.
Operation:
Follow the instructions on the following page.
Troubleshooting and service:
If faults occur, please contact our
Aftersales Service [email protected]
Maintenance and Cleaning
On the internet: vs.de/kataloge/reinigung/en
Forwarding and Disposal:
If the product is passed on to any third party then these instruc-
tions must be supplied with it. Please contact your relevant
local authority for information on environmentally compatible
disposal. The indicated electric and electronic components
must not be disposed of with the ordinary waste.
They must be removed from the furniture unit before
the unit is sent for disposal. They are to be disposed
of at authorized collection and return points.

4
Procedure for concatenation
1. Remove protective caps (1) and fold out the connector
[Fig. 1].
2. Fold out the connecting pieces (2) and push the elements
together. The connecting pieces must engage in the corre-
sponding retainers [Fig. 2+3].
3. Using the supplied Allen key WAF 7 (3), lock the elements
to each other through the opening in the upholstery (turn
counterclockwise!) [Fig. 4].
4. Disassembly is performed in reverse sequence.
5. In the event of floor unevenness release the screws with an
Allen key WAF 5. Adjust the levelling wedgesile (4) (offset)
and screw again. (At maximum adjustment the screws must
be twisted out completely) [Fig. 5+6].
Procedure for establishing electrical
connections
1. Position the mounting plate (5) at a distance of 30 mm
from the front edge of the Lounge element. Assembly is
usually performed in the centre of a straight Lounge element.
Alternatively, installation is possible in accordance with the
customer’s requirements [Fig. 7].
2. Fix the mounting plate (5) of the electrical connection
unit (8) to the underside of the Lounge element using four
PH 4.0x20 mm chipboard screws (6) [Fig. 8].
3. Now engage the electrical connection unit (8) at the
mounting plate (5) (push to the right) [Fig. 9]. The strain
relief mechanism for the connecting cable is already inte-
grated in the unit.
Caution! The mains power line to the electrical
connection unit must be positioned in such a way
that there is no danger of tripping and falling.
4. Finally, you must secure the unit against disassembly by
inserting a locking screw (7) (PH 4.0x20 mm chipboard
screw (6)) to the left next to the unit. This is to prevent the
electrical connection unit (8) from being accidentally
pushed out of the mounting plate (5) [Fig. 9].
(1) (2)
(3)
(4)
(4)
1 2
3 4
5 6
(7)
(5)
(6)
(7)
(8)
7
8
9
(5)
(8)