Vulcan-Hart GCO2C User manual

GCO2D & GCO2C
GAS CONVECTION OVENS
MODEL
GCO2D ML-114569
GCO2C ML-114571
VULCAN-HART COMPANY, P.O. BOX 696, LOUISVILLE, KY 40201-0696, TEL. [phone]
FORM 30975 Rev. C (Aug. 2000) www.vulcanhart.com
INSTALLATION &
OPERATION MANUAL
MODEL GCO2D

– 2 –
IMPORTANT FOR YOUR SAFETY
THIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIED TO INSTALL GAS
EQUIPMENT, WHO SHOULD PERFORM THE INITIAL FIELD START-UP AND
ADJUSTMENTS OF THE EQUIPMENT COVERED BY THIS MANUAL.
POST IN A PROMINENT LOCATION THE INSTRUCTIONS TO BE FOLLOWED IN THE
EVENT THE SMELL OF GAS IS DETECTED. THIS INFORMATION CAN BE OBTAINED
FROM THE LOCAL GAS SUPPLIER.
IMPORTANT
IN THE EVENT A GAS ODOR IS DETECTED, SHUT DOWN
UNITS AT MAIN SHUTOFF VALVE AND CONTACT THE
LOCALGASCOMPANYORGASSUPPLIERFORSERVICE.
FOR YOUR SAFETY
DO NOT STORE OR USE GASOLINE OR OTHER
FLAMMABLE VAPORS OR LIQUIDS IN THE VICINITY OF
THIS OR ANY OTHER APPLIANCE.
WARNING: IMPROPER INSTALLATION, ADJUSTMENT,
ALTERATION, SERVICE OR MAINTENANCE CAN CAUSE
PROPERTY DAMAGE, INJURY OR DEATH. READ THE
INSTALLATION, OPERATING AND MAINTENANCE
INSTRUCTIONSTHOROUGHLYBEFOREINSTALLINGOR
SERVICING THIS EQUIPMENT.
INTHE EVENTOF APOWERFAILURE,DONOT ATTEMPT
TO OPERATE THIS DEVICE.
© VULCAN-HART COMPANY, 1996

– 3 –
TABLE OF CONTENTS
GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Installation Codes and Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installing Basic Oven . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Assembling the Legs to the Single Oven. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Assembling the Chimney to the Single Oven . . . . . . . . . . . . . . . . . . . . . . . . . 5
Assembling the Oven to the Stand. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Assembling Stacked Ovens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Leveling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Electrical Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Gas Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Testing the Gas Supply System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Gas Pressures and Orifices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Burner Air Shutter Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Flue Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
OPERATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Controls — Model GCO2D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Lighting the GCO2D Oven . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Before First Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Using the GCO2D Oven . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Controls — Model GCO2C Built before October 1999 . . . . . . . . . . . . . . . . . 10
Thermostat Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Timer Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Lighting the GCO2C Oven . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Before First Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Using the GCO2C Oven . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Error Messages — Model GCO2C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Controls — Model GCO2C Built after October 1999 . . . . . . . . . . . . . . . . . . 14
Manually Setting the Temperature and Cook Time . . . . . . . . . . . . . . . . . . . 15
To Program Menu Item and Rack # Cook Times . . . . . . . . . . . . . . . . . . . . . 15
Setting the Oven for Roast & Hold. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Roast and Hold Operation — Model GCO2C . . . . . . . . . . . . . . . . . . . . . . . . 17
Proper Utensils . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Conserving Energy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Operating Hints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Suggested Cooking Guidelines — Models GCO2D and GCO2C . . . . . . . . 18
For Best Results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Disconnecting the Gas Line Restraint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Service and Parts Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

– 4 –
Installation, Operation, and Care of
GCO2D & GCO2C
GAS CONVECTION OVENS
KEEP THIS MANUAL FOR FUTURE USE
GENERAL
TheGCO2DGasConvectionOvenisasinglecavityovenandfeaturesasolidstatethermostat,1-hour
dial timer, and five racks as standard equipment. Additional oven racks are optional. Each oven is
equipped with a 25,000 Btu/hr burner and a 1⁄2HP (0.37 kw) electric motor. The oven comes standard
with painted grey exterior and porcelain interior; stainless steel interior and exterior are optional.
Stainlesssteeldoorwithwindow(doorhingingisfieldreversible)andstainlesssteelfrontarestandard.
Model GCO2C has different controls than the GCO2D.
Two single ovens can be ordered with a stacking kit for mounting one oven on top of the other.
A single oven may be installed on an open stand with lower storage rack (optional).
Your Vulcan Gas Convection Oven is produced with quality workmanship and material. Proper
installation,usageandmaintenanceofyourovenwillresultinmanyyearsofsatisfactoryperformance.
Vulcan-Hart Company suggests that you thoroughly read this entire manual and carefully follow all of
the instructions provided.
LEDOMLEDOM LEDOM LEDOMLEDOMTATSOMREHTTATSOMREHT TATSOMREHT TATSOMREHTTATSOMREHTREMITREMIT REMIT REMITREMIT &TSAOR&TSAOR &TSAOR &TSAOR&TSAOR DLOHDLOH DLOH DLOHDLOH ELTNEGELTNEG ELTNEG ELTNEGELTNEG EKABEKAB EKAB EKABEKAB KOOC#KCARKOOC#KCAR KOOC#KCAR KOOC#KCARKOOC#KCAR SEMITSEMIT SEMIT SEMITSEMIT
D2OCGetatSdiloSlaiDruoH-1
9991rebotcOerofebC2OCGcinortcelEcinortcelEXX
9991rebotcOretfaC2OCGelbammargorPelbammargorPX X
INSTALLATION
UNPACKING
Immediately after unpacking the oven, check for possible shipping damage. If this oven is found to be
damaged, save the packaging material and contact the carrier within 15 days of delivery.
Prior to installation, verify that the electrical supply and type of gas (natural or propane) agree with the
specifications on the oven data plate, located on the inside of the top front cover.
Do not use the door or its handle to lift the oven.
LOCATION
The equipment area must be kept free and clear of combustibles. Clearance from combustible or non-
combustible construction of at least 3" (7.6 cm) on the sides and 3" (7.6 cm) at the back are required. The
installation location must allow adequate clearance for servicing and proper operation.
The oven must be installed so that the flow of combustion and ventilation air will not be obstructed.
Adequate clearance for air openings into the combustion chamber must be provided. Make sure there
is an adequate supply of air in the room to allow for combustion of gas at the oven burners.

– 5 –
INSTALLATION CODES AND STANDARDS
Inthe UnitedStates, Vulcangas ovensmust beinstalled inaccordance with: 1)State andlocal codes;
2) NationalFuelGasCode,ANSI-Z223.1(latestedition),availablefromAmericanGasAssociation,1515
Wilson Boulevard, Arlington, VA 22209; 3)ANSI/NFPA 96, Vapor Removal from Cooking Equipment
(latest edition), available from National Fire Protection Association, Batterymarch Park, Quincy, MA
02269; and 4) National Electrical Code, NFPA-70 (latest edition).
In Canada, Vulcan gas ovens must be installed in accordance with: 1)Local codes; 2) CAN/CGA-
B149.1, NaturalGasInstallation Code (latestedition)orCAN/CGA-B149.2, PropaneInstallationCode
(latest edition), available from Canadian Standards Association, 178 Rexdale Boulevard, Etobicoke,
Ontario, Canada M9W 1R3; and 3) Canadian Electrical Code, CSA Standard C22.2 No. 3,
Electrical
Features of Fuel Burning Equipment
(latest edition).
INSTALLING BASIC OVEN
The basic oven must be installed on 4" (10 cm) or 6" (15 cm) adjustable legs for counter installation or
be mounted on a modular stand. Installations on concrete bases or other supports restricting air
circulation underneath the oven are not advisable and may void the warranty.
When the oven is mounted on casters, it must be installed with the
casterssupplied,aconnector(notsuppliedbyVulcan-Hart)complying
with either ANSI Z21.69 (latest edition) or CAN/CGA-6.16 (latest
edition), and a quick-disconnect device complying with either ANSI
Z21.41 (latest edition) or CAN1-6.9 (latest edition). It must also be
installed with a restraint device to prevent strain on the connector.
Remove two screws from the rear of the oven and install the tie down
strapshipped withthe casters usingthese screws. Attachthe gasline
strain relief to the tie down strap at the rear of the oven (Fig. 1).
Assembling the Legs to the Single Oven
The 4" (10 cm) or 6" (15 cm) legs are packed inside the oven during shipment and must be installed on
the bottom of the oven. Place the oven on its left side, being careful to avoid scratching the finish. The
gas pipe connection protrudes beyond the back; provide for this when oven is tipped back by resting
it on suitable spacers (2 x 4's etc.).
Thread each of the four leg assemblies into the holes provided on the
bottomcornersoftheoven.Carefullyraisetheoventoitsnormalupright
position.
Assembling the Chimney to the Single Oven
Remove the chimney from inside the oven cavity and use the screws
provided to fasten the chimney to the top rear of the oven (Fig. 2). The
flanges on the chimney are to be positioned over the top cover.
ASSEMBLING THE OVEN TO THE STAND
Position the oven on its back, taking care not to scratch or damage it. The gas pipe connection
protrudes beyond the back; provide for this when the oven is tipped back by resting it on suitable
spacers (2 x 4's). Install the two locating studs (included in the stand carton) into the screw plates on
the underside of the oven (Fig. 3).
Attach each of the four leg assemblies to the bottom of the stand with the 12 bolts and lockwashers
(3perleg). Ifcastersare usedinsteadoflegs,put fixedcastersinrearandswivel castersinfrontusing
12 bolts and lockwashers (3 per caster). Mount the oven on top of the stand.
Fig. 1
CHIMNEY
PL-52240
Fig. 2
CONNECT
GAS LINE
STRAIN RELIEF
HERE
PL-53563

– 6 –
REAR OF TOP OVEN
KNOCK OUT WELDED PLATE
FOR FLUE EXTENSION INSTALLATION
BOTTOM
LOCATING STUDS
PL-52992
FRONT OF TOP OVEN
ASSEMBLING STACKED OVENS
Determinewhichovenwillbeonthebottomandplaceitonitsleftside,
being careful to avoid scratching the finish. Install the four 163⁄4"
(42.5 cm) legs,usingthe24boltsandlockwashersprovided(6perleg).
Remove the two 7/16" (1.1 cm) knockouts on each side of the top cover
and place oven in upright position at installation location. Turn the
adjustable feet in or out to level the oven front-to-back and side-to-
side (refer to LEVELING, page 6).
Remove right side panels from both ovens. Remove welded plate
from bottom of upper oven (Fig. 3). Install the two locating studs
(includedin the leg stackset) into screw plateson underside of upper
oven(Fig. 3).Placeupperovenontopoflowerovenusingthelocating
studs.
Remove flue extension from upper oven. Install long flue extension
intoexistingright-angledflueextensioninloweroven.Attachlongflue
extension to wall of upper oven using screws provided. Secure
chimney to roof of upper oven (Fig. 4).
Install right side panels on both ovens. Connect the piping between
thetop ovenand bottom oven.Pipe jointcompound mustbe resistant
to the action of propane gases.
Themanualgasvalveatthebottomofthecontrolpanelshouldremain
offuntilallelectricalconnectionsaremadeandtheovensarechecked
or used.
LEVELING
Once the oven is in its permanent position, place a carpenter's level
on the oven rack. If the oven is installed on legs, turn the adjustable
feet in or out to level oven front-to-back and side-to-side. If the oven
is installed on casters, loosen set screws and turn casters in or out to
level oven front-to-back and side-to-side. Retighten set screws after
leveling.
ELECTRICAL CONNECTIONS
WARNING: ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE
APPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL
ELECTRICAL CODES.
WARNING:DISCONNECTELECTRICALPOWERSUPPLYANDPLACEATAGATTHEDISCONNECT
SWITCH TO INDICATE THAT YOU ARE WORKING ON THE CIRCUIT.
WARNING: APPLIANCESEQUIPPEDWITHAFLEXIBLEELECTRICSUPPLYCORDAREPROVIDED
WITHATHREE-PRONGGROUNDINGPLUG. THISPLUGMUSTBECONNECTEDTOAPROPERLY
GROUNDED THREE-PRONG RECEPTACLE. IF THE RECEPTACLE IS NOT THE PROPER
GROUNDING TYPE, CONTACT AN ELECTRICIAN. DO NOT REMOVE THE GROUNDING PRONG
FROM THE PLUG.
The 120 volt models are equipped with a cord and plug.
Refer to electrical wiring diagram located inside the right side panel; remove control panel for access.
Fig. 3
Fig. 4
RIGHT ANGLED
FLUE EXTENSION
LONG FLUE
EXTENSION
CHIMNEY
PL-52221

– 7 –
Donotturnthepowersupplyonuntilafterthegasconnectionshavebeenmadeandcheckedforleaks.
ATADLACIRTCELEATADLACIRTCELE ATADLACIRTCELE ATADLACIRTCELEATADLACIRTCELE
ledoMledoM ledoM ledoMledoMstloVstloV stloV stloVstloVztreHztreH ztreH ztreHztreHesahPesahP esahP esahPesahP yticapmAtiucriCmuminiMyticapmAtiucriCmuminiM yticapmAtiucriCmuminiM yticapmAtiucriCmuminiMyticapmAtiucriCmuminiM eciveDevitcetorPmumixaMeciveDevitcetorPmumixaM eciveDevitcetorPmumixaM eciveDevitcetorPmumixaMeciveDevitcetorPmumixaM SPMASPMA SPMA SPMASPMA
D2OCG 021061 51
042–002051 51
042–802061 51
C2OCG 021061 51
042–00206/051 51
.)noitidetsetal(07-APFN,edoClacirtcelElanoitaNehthtiwecnadroccanidelipmoC
GAS CONNECTION
ATADSAGATADSAG ATADSAG ATADSAGATADSAG
ledoMledoM ledoM ledoMledoM RH/UTBTUPNIRH/UTBTUPNI RH/UTBTUPNI RH/UTBTUPNIRH/UTBTUPNIERUSSERPDLOFINAMERUSSERPDLOFINAM ERUSSERPDLOFINAM ERUSSERPDLOFINAMERUSSERPDLOFINAM
larutaNlarutaN larutaN larutaNlarutaNenaporPenaporP enaporP enaporPenaporPlarutaNlarutaN larutaN larutaNlarutaNenaporPenaporP enaporP enaporPenaporP
C2OCG,D2OCG000,52000,52)aPk8.0(.c.w"5.3)aPk5.2(.c.w"01
For all gas supply connections, pipe joint compound must be resistant to the action of propane gases.
The oven is provided with a regulator integral to the gas solenoid valve, and requires no regulator
external to the device. A gas shutoff valve is supplied with each oven and is located at the bottom of
the control panel. No tools are required to access this valve.
Connect the oven(s) to the gas line after leveling. The gas supply line must be at least the equivalent
of 3⁄4" (1.9 cm) iron pipe. Make sure the pipes are clean and free of obstructions, dirt and piping
compound.
WARNING: PRIOR TO LIGHTING, CHECK ALL JOINTS IN THE GAS SUPPLY LINE FOR LEAKS.
USE SOAP AND WATER SOLUTION. DO NOT USE AN OPEN FLAME.
TESTING THE GAS SUPPLY SYSTEM
The oven and its individual shutoff valve must be disconnected from the gas supply piping system
during any pressure testing of that system at test pressures greater than 1/2psig (3.45 kPa).
Theovenmustbeisolatedfromthegassupplypipingsystembyclosingthemanualshutoffvalveduring
pressure testing of the gas supply system at test pressures equal to or less than 1/2psig (3.45 kPa).
GAS PRESSURES AND ORIFICES
Natural Gas
The burner orifices are sized to deliver the nameplate input rating (25,000 Btu/hr) at a gas manifold
pressureof3.5"w.c. (watercolumn)(0.8 kPa). Thegaspressureregulator isintegraltothe gassolenoid
valve, and is factory set to supply 3.5" w.c. (0.8 kPa) as required for natural gas.
Propane Gas
The burner orifices are sized to deliver the nameplate input rating (25,000 Btu/hr) at a gas manifold
pressureof10.0"w.c.(watercolumn)(2.5kPa).Thegaspressureregulatorisintegraltothegassolenoid
valve, and is factory set to supply 10.0" w.c. (2.5 kPa) as required for propane gas.
BURNER AIR SHUTTER ADJUSTMENTS
The burner has fixed, factory adjusted air openings and requires no field adjustment.

– 8 –
PL-52225
ON
HEAT
IGNITION
TIMER
ON
OFF
GAS VALVE
GAS VALVE
THERMOSTAT
TO SHUT
OVEN OFF
PLACE MASTER SWITCH IN
"OFF" POSTION TURN GAS
VALVE OFF
,,
,,
TO SHUT
OVEN OFF
PLACE MASTER SWITCH IN
"OFF" POSTION TURN GAS
VALVE OFF
,,
,
,
,,
,,
,,
MASTER
SWITCH
,
,
ON
OFF
OVEN
COOL
,
,
,
ON
OFF
,
,
,
40
45
50
55
25
30
35
20
15
510
60
0
425
450
475
400
350 300
250
225
150
300
500
T
E
M
P
F
O
F
F
MASTER SWITCH
ON LIGHT
HEAT LIGHT
NO IGNITION LIGHT
THERMOSTAT
TIMER
OVEN COOL SWITCH
FLUE CONNECTION
Ventilation requirements will vary with each installation and must comply with
Vapor Removal from
Cooking Equipment
, NFPA Standard #96 (latest edition) and with local codes. Considerations to be
kept in mind include:
• Flue connections should never be made directly to the oven.
• The oven should be located under a hood which has an adequate connection to an exhaust duct
and extends 6" (15 cm) beyond the oven sides.
• Clearance above the oven flue should be adequate for the flue products to escape so that there
is no interference with heat circulation in the ovens.
OPERATION
WARNING: THE OVEN AND ITS PARTS ARE HOT. USE CARE WHEN OPERATING, CLEANING,
OR PERFORMING ANY MAINTENANCE.
CONTROLS — MODEL GCO2D (Fig. 5)
Fig. 5
MASTER SWITCH • Turns oven control circuits ON or OFF.
OVEN COOL SWITCH • Allows the fan motor to run with the
door ajar to speed oven cooling.
THERMOSTAT • Controls oven temperature during cooking
operation.
TIMER • Use to set cooking cycle time. The timer range is from
0 to 60 minutes. Alarm sounds continuously when
elapsed time counts down to 0; oven does not turn off.
Turn timer to OFF position to stop alarm. When oven is
not in use, keep timer at OFF position.
ON LIGHT (Amber) • Is lit when MASTER SWITCH is ON.
HEATLIGHT(White)•Comesonandgoesoffwhentheburner
cycles on and off.
NO IGNITION LIGHT (Red) • Comes on if burner fails to ignite
after the third try. When lighting the oven, the NO
IGNITION LIGHT cycles ON during the 5 second purge
and OFF during the 7 second ignition trial.
GAS VALVE • When ON, allows gas to flow to the ignition
system.

– 9 –
LIGHTING THE GCO2D OVEN
Open the manual valve. Turn the MASTER switch ON and turn the thermostat to its maximum setting.
Both the ON and HEAT lights should be lit. If the HEAT light is not on, make sure the door is closed.
After 5 seconds, the spark ignition system will initiate and the solenoid valve will open, allowing gas
flow to the burner for a period of 7 seconds. This 5 second purge and 7 second ignition trial will repeat
itself up to two more times if the burner does not light within the first 7 second ignition trial. During the
5 second prepurge, the red NO IGNITION light will be lit.
When the burner gas ignites, a slight roar will be audible. This roar is a normal condition of the power
burner, and will become almost undetectable in the normal operating mode after warm-up. The NO
IGNITION light will go off when ignition occurs.
If the burner fails to light after three trials, the red NO IGNITION light will be illuminated and remain
on. Turn the MASTER switch OFF for five minutes before repeating the operating sequence listed
above.
If burners do not light after five trials, turn off the manual valve and call a qualified servicer.
BEFORE FIRST USE
Before the oven is used for the first time, it must be "burned in" to release any odors that might result
from heating the new surfaces in the chamber.
Using a clean damp cloth, wipe the inside of the oven, including the racks.
Close the oven door, turn the MASTER switch ON, turn the thermostat to 300°F (149°C) and allow the
oven to cycle for 6 to 8 hours before turning the switch OFF.
USING THE GCO2D OVEN
Preheating
1. Turn the MASTER switch ON. The amber ON light will glow, indicating that power to the oven
is on.
2. Set the THERMOSTAT as desired. Refer to SUGGESTED COOKING GUIDELINES — MODEL
GCO2D for temperatures and times for various products.
3. Prepare the product and place in suitable pans. When the white HEAT light goes off, the oven
has reached desired preheat temperature.
Cooking
1. Open the door and load the product into the oven. Place the pans in the center of racks. Close
the door.
2. Set the TIMER. After the preset time lapses, turn the timer OFF to stop the buzzer.
3. Whentheproductisdone,openthedoorandcarefullyremovethecookedproductfromtheoven.
Wipe up any spills.
End of Day
1. Turn the THERMOSTAT OFF.
2. Turn the OVEN COOL switch ON.
3. Leave door ajar while the fan is on to cool the oven.
4. Whenovenhascooledsufficiently,turnOVENCOOLswitchandMASTERswitchOFFandclean
the oven.

– 10 –
CONTROLS — MODEL GCO2C Built before October 1999 (Fig. 6)
Fig. 6
THERMOSTAT CONTROL
Temperature Display (When not timing product).
Displays set cook temperature while the light in the Roast Button is lit. Will be overridden to display
actual cavity temperature for 8 seconds when Thermometer Button is pushed.
1. The light in the Thermometer Button is lit while the actual temperature is being displayed.
2. ThelightintheThermometerButtonisnotlitwhenthedisplayreturnstosettemperaturedisplay.
Temperature Display (When product is being timed).
Displays set hold temperature while the light in the Hold Button is lit. Displays the roast temperature
whentheRoastButtonislit.Willbeoverriddentodisplayactualcavitytemperaturefor8secondswhen
the Thermometer Button is pushed.
1. The light in the Thermometer Button is lit while actual temperature is being displayed.
2. ThelightintheThermometerButtonisnotlitwhenthedisplayreturnstosettemperaturedisplay.
Temperature Knob (When not timing product).
1. Sets the roast temperature when the Roast Button light is lit. The Roast Button light can be
turned on by pressing the Roast Button.
2. Sets the hold temperature when the Hold Button light is lit. The Hold Button light can be turned
on by pressing the Hold Button.
Temperature Knob (When product is being timed).
1. Sets the roast temperature when the Roast Button light is lit. The Roast Buttonlightcannotbe
changed by pressing the Roast Button.
2. Sets the hold temperature when the Hold Button light is lit. The Hold Button light cannot be
changed by pressing the Hold Button.
OFF
ON
POWER
COOL
DOWN
HEAT
ROAST HOLD
READY
TIME
TEMPERATURE
START
STOP
TIME GENTLE
BAKE
THERMOSTAT
ON / OFF / OVEN COOL
TIMER KNOB
TEMPERATURE KNOB
HOLD BUTTON
TIMER
SWITCH
THERMOMETER BUTTON
GENTLE BAKE BUTTON
START/STOP BUTTON
ROAST BUTTON
TIME BUTTON
PL-52224
GAS VALVE
ads;fjj;flPUSH MASTER SWITCH TO
"ON" POSTION. IF OVEN
FAILS TO LIGHT. PUSH
LIGHTING INSTRUCTIONS
da;la;lasjfd;a
sdifja;lldfjlfdal;
ds;fjalkdfja;sjdf;lfsdj;a;l
asdhflkajseflasdkjhflasklasj
shdjflkajh
ON
,
OFF
,,
,,
GAS VALVE
,
,,,
,,,
,,,
,,,
READY LIGHT
HEAT LIGHT

– 11 –
Roast Button Light (If On and not timing product, indicates the roast mode is selected).
• ThedisplayedtemperaturesettingswillbefortheroasttemperatureexceptwhentheThermometer
Button is lit.
• Rotating the Thermostat Knob will change the roast set temperature.
• Cook time can be adjusted using the Timer Knob.
• The time displayed is the initial set cook time.
• It is possible to select the Hold mode using the Hold Button.
Roast Button Light (If On and product is being timed, indicates the roast mode is selected).
• ThedisplayedtemperaturesettingswillbefortheroasttemperatureexceptwhentheThermometer
Button is lit.
• Rotating the Temperature Knob will change the roast set temperature.
• It is not possible to select the Hold mode using the Hold Button.
• The time displayed is the time counted down from the initial cook time setting.
Roast Button
1. Selects the Roast mode, indicated by the Roast Button Light described above.
2. Has no effect if timing in the Hold mode.
Thermometer Button — When pressed, displays the actual oven temperature for about 8 seconds,
then returns to the set temperature.
Heat Light —When lit, indicates that power is being supplied to the burner.
Ready Light — Is lit when the actual temperature is within 5°F (3°C) of the set temperature for the
current mode, plus or minus.
TIMER CONTROL
Time Display (While not timing product).
— Displays the set cook time if the light in the Roast Button is lit.
Time Display (While product is being timed).
1. Displays the counted down cook time if the Roast Button light is lit in the Roast mode.
2. Displaysthe countedup holdtime ifthe HoldButton is litin theHold mode.Count-up ofhold time
does not begin until cavity temperature reaches the hold temperature.
Time Display Colon
1. Is flashing if product is timing.
2. Is not flashing if product is not being timed.
Time Button — Press to set cooking cycle time.
Time Button Light — Is lit when the Time Button is pressed.
Timer Knob — Sets the cook time when not already timing and the Cook Time indicator is lit.

– 12 –
Gentle Bake Button
Selects the gentle bake time setting. A roast time must first be set. The gentle bake time can then be
set at the roast time value or less. The gentle bake time will be the portion of roast time to operate in
the gentle bake mode. Gentle bake mode will start first. When the gentle bake time has lapsed, the
remainder of the roast time will be in the non-gentle bake mode.
Use Gentle Bake when cooking delicate product, such as strudel, muffins, cupcakes, meringue pies,
etc., to keep product from forming waves on the top.
Use the Gentle Bake Button to switch between the selection of gentle bake mode and no gentle bake
mode time setting. A gentle bake mode time of zero means no gentle bake mode will occur.
The light in the Gentle Bake Button is lit during gentle bake mode.
Gentle Bake Mode
1. The fan cycles (45 seconds ON and 45 seconds OFF) throughout the gentle bake mode.
2. The fan stays on while the heat cycles in hold mode.
3. The fan stays on while heat cycles at 100% power when not timing.
4. Can be switched at any time.
Stop / Start Button
1. Starts timing a product in the mode selected if a cook time has been set.
2. Stops timing a product if a timing sequence is already in progress.
Hold Button — Selects Hold mode.
1. Allows selection of hold temperature.
2. Temperature indication of ---°F (---°C) indicates no hold mode.
Hold Button Light — Is lit when in the Hold mode.
1. When not timing, allows setting/enabling a hold mode setting of ---°F (---°C), meaning no hold
will take effect.
2. Any other temperature means that when the actual cook time has ended, the oven will enter the
Hold mode and use the hold temperature.
On / Off / Oven Cool Switch
1. ON turns oven control circuits on.
2. OFF turns oven control circuits off.
3. OVEN COOL allows the fan motor to run with the door ajar to speed oven cooling.
Gas Valve — When ON, allows gas to flow to the ignition system.
LIGHTING THE GCO2C OVEN
1. Turn manual gas valve ON.
2. Push ON / OFF / OVEN COOL switch to the ON position and set THERMOSTAT to its maximum
setting. The HEAT light should come on. If HEAT light is not on, make sure the door is closed.
3. If the oven fails to light, push the ON / OFF / OVEN COOL switch OFF. Wait 5 minutes before
trying to re-light the oven.

– 13 –
BEFORE FIRST USE
Beforeusingtheovenforthefirsttime,itmustbe"burnedin"toreleaseanyodorsthatmightresultfrom
heating the new surfaces in the chamber.
1. Using a clean damp cloth, wipe the inside of the oven, including the racks.
2. Close the oven door, push the ON / OFF / OVEN COOL switch ON, turn the THERMOSTAT to
300°F (149°C) and allow the oven to cycle for 6 to 8 hours before turning the ON / OFF / OVEN
COOL switch OFF.
USING THE GCO2C OVEN
Preheating
1. Close the oven door. Push ON / OFF / OVEN COOL switch ON. The HEAT light will come on,
indicating that power to the oven is on.
2. SetTHERMOSTATasdesired.RefertoSUGGESTEDCOOKINGGUIDELINESfor temperatures
and times.
3. Prepare product and place in suitable pans. When READY light comes on, oven has reached
desired preheat temperature.
Cooking
1. Open the door and load the product into the oven. Place the pans in the center of racks. Close
the door.
2. Set ROAST temperature and time. Set HOLD temperature and GENTLE BAKE time, if desired.
GENTLE BAKE time cannot be more than ROAST time. GENTLE BAKE will cycle the fan during
the set time at the beginning of the cooking cycle.
3. Press the START/STOP button to start the cooking cycle.
4. At the end of the cooking cycle, the buzzer will sound continuously if the HOLD mode is OFF. If
theHOLDmodeisON,therewillbeashortbeepatthebeginningofSecondStageCooking(oven
temperaturewill beginto declineto theHOLD temperature),and a longbeep (20seconds) atthe
end of the cooking cycle. (Refer to ROAST AND HOLD OPERATION.)
5. When product is done, open the door and carefully remove cooked product from the oven. Wipe
up any spills.
End of Day
1. PushON / OFF /OVEN COOL switch toOVEN COOL. Leave doorajar while thefan is on tocool
the oven.
2. When the oven has cooled sufficiently, turn the ON / OFF / OVEN COOL switch OFF and clean
the oven.
ERROR MESSAGES — Model GCO2C
E-01 High limit error. Contact Vulcan authorized service.
E-02 Low limit error. Contact Vulcan authorized service.
E-03 High ambient temperature, 215°F (102°C). Contact Vulcan authorized service.
E-04 Low ambient temperature, 32°F (0°C). Let control warm up after cold storage.
E-05 Ignition failure. After trying ignition three times, contact Vulcan authorized service.
E-06 Thermocouple probe open. Contact Vulcan authorized service.
When calling for service, please advise what error code was displayed.

– 14 –
1
2
SET
PRIMARY
SECONDARY
MENU SELECT
MODE
R & H READY
OVEN HEATING OVEN
POWER
ROAST
&
HOLD
ON
ON
NO IGNITION
OFF
OFF
COOL
OVEN
MENU RACK
3
4
5
PL-53543
6
5
START
STOP
4
3
2
1
CONTROLS — MODEL GCO2C Built after October 1999
Always displays [HR:Min] when setting the time.
Displays [HR:Min] if the countdown Time is more than 1 Hour.
Displays [Min:Sec] if the countdown Time is less than 1 Hour.
Displays Temperature in °F.
R & H
MODE
Indicates the oven is in the Roast and Hold Mode.
OVEN
READY
Indicates the oven is preheated and ready for cooking.
OVEN
HEATING
Indicates the oven is preheating.
PRIMARY Primary indicates Menu Items 1, 3, or 5.
SECONDARY
Secondary indicates Menu Items 2, 4, or 6.
Up arrow increases; Down arrow decreases — a displayed
Time or Temperature value (if arrow keys are lit).
TEMPERATURE: Use with SET to set the oven Temperature.
SET
SET: Use with Time or Temperature.
TIME: Use with SET to manually set the cooking Time.
ROAST
&
HOLD
Changes to Roast and Hold mode.
START
STOP
Press once to start; press a second time to stop.
1/2
3/4
5/6
Select Menu Cook Times. Press once for Primary (1, 3, or 5).
Press a second time for Secondary (2, 4, or 6). See next page.
1
2
3
4
5
Rack Buttons select individual Menu / Rack # Cook
Times — once programmed.

– 15 –
MANUALLY SETTING THE TEMPERATURE AND COOK TIME
To Set the Temperature
• Press the SET button. Press the TEMPERATURE button;
StPt displays to indicate Setpoint.
• Use the Up and Down Arrow keys to increase or decrease the displayed Temperature value.
• Press the SET button again to save the Temperature setpoint in the computer.
To Set the Cook Time
• Press the SET button. Press the TIME button. Tine displays to indicate TIME.
• Use the Up and Down Arrow keys to increase or decrease the displayed Cook Time (HR:min).
• Press the SET button again to save the Time setting in the computer.
To Start Cooking
• Press the START / STOP button.
• ThemanualCook Timecountsdownto 00:00. Displays[HR:Min]above 1hour;[min:sec] below.
• The buzzer will sound. To silence the buzzer, press the START / STOP button again.
* The control retains the manual settings for Temperature and Time.
TO PROGRAM MENU ITEM and RACK # Cook Times
Factory Preset and Programmable Cook Times are shown in the table, below:
NOITCELESUNEM UNEM METIMETI METI METIMETI
TESERPYROTCAF METIUNEMMETIUNEM METIUNEM METIUNEMMETIUNEM EMITKOOCEMITKOOC EMITKOOC EMITKOOCEMITKOOC
SEULAVELBAMMARGORP
METIUNEM EMITKOOCEMITKOOC EMITKOOC EMITKOOCEMITKOOC 1KCAR EMITKOOCEMITKOOC EMITKOOC EMITKOOCEMITKOOC 2KCAR EMITKOOCEMITKOOC EMITKOOC EMITKOOCEMITKOOC 3KCAR EMITKOOCEMITKOOC EMITKOOC EMITKOOCEMITKOOC 4KCAR EMITKOOCEMITKOOC EMITKOOC EMITKOOCEMITKOOC 5KCAR EMITKOOCEMITKOOC EMITKOOC EMITKOOCEMITKOOC
yramirP2/11.nim01
yradnoceS2/12.nim51
yramirP4/33.nim02
yradnoceS4/34.nim52
yramirP6/55.nim03
yradnoceS6/56.nim53
The Primary indicator light with Menu 1 / 2 selects Menu Item 1 (Factory Preset Cook Time = 10
minutes). TheSecondaryindicatorlightwithMenu1/2selectsMenuItem2(FactoryPresetCookTime
= 15 minutes). Similarly, for Menu Buttons 3 / 4 or 5 / 6. Any Menu Item Cook Time can be changed
using the procedure below. Rack # Cook Times may be programmed if desired but are not required.
To Change the Time Setting for any Menu Item (1 – 6)
• To enter program mode, press and hold the Up and Down arrow buttons until PrOG displays.
✤Select the Menu Item to be programmed (1 – 6). Tine displays to indicate TIME. Use the Up and
Down arrow buttons to increase or decrease the Menu Item's COOK TIME. Repeat this step for
any other Menu Items.
• Press the START / STOP button; LOC displays. Press the START / STOP button a second time
to save the Menu Item(s)' COOK TIME(s).
• Press the START / STOP button once to begin cooking (with the Menu Item's Cook Time). To
exit, press the START / STOP button a second time.
To Program Individual Rack # Cook Times for a Menu Item
• To enter program mode, press and hold the Up and Down arrow buttons until PrOG displays.
• Select the Menu Item to be programmed (1 – 6);
Tine displays to indicate TIME.
✤Then select the Rack # (1 – 5). [ t 1 ] indicates Rack #1; [ t 2 ] indicates Rack #2; ... [ t 5 ] indicates
Rack #5. Use the Up and Down arrows to increase or decrease the COOK TIME for any Rack #.
• Press the START / STOP button;
LOC displays. Press the START / STOP button a second time
to save the Menu / Rack #'s COOK TIME(s).
• To exit program mode, press START / STOP twice.

– 16 –
Always Set the Temperature Before Setting the Time
• Press the SET button. Press the TEMPERATURE button;
StPt displays. Use the Up and Down
Arrow keys to increase or decrease the Temperature. To save, press the SET button again.
At startup, the display will initially show a
GROWING BAR . When the oven temperature reaches the Set
Point, the set temperature displays. The READY light is lit, the HEAT light goes out, and the oven is
ready for you to select the Cook Time, Menu Item Cook Time, or Menu / Rack # Cook Time.
Starting a Timed Cycle On All Racks
• Open the door,
door will display.
• Place the desired product on any of the five racks.
• Close the door. The display should return to the set temperature or the
GROWING BAR .
• Press the Menu Key once for Primary or twice for Secondary to select a Menu Item Cook Time.
• Press the START / STOP button *.
• The timer will count down the time remaining for the Menu Item Cook Time.
• When the time has counted down to 00:00, the buzzer will sound and all Rack Buttons will flash.
• To silence the buzzer, press the START / STOP button.
*
Pressing the START / STOP button after making a menu selection will time all racks for the
selected menu time.
Starting a Timed Cycle Using Programmed Individual Menu / Rack # Cook Time(s)
• After the set Temperature is reached, open the door;
door displays. Place product(s) in oven.
• Close the door. The display returns to the set Temperature or the
GROWING BAR .
• Select the Menu Item (once for Primary or twice for Secondary) and the Rack # to select the
Menu / Rack # Cook Time. If using simultaneous cook times, select the other Menu / Rack #'s.
• The timer selects the Rack # with the shortest Cook Time and counts down to 00:00.
• The buzzer sounds and the Rack # flashes. To silence the buzzer, press the flashing Rack #.
• Open the door;
door displays; remove the finished product; close the door.
✣The next shortest Cook Time displays, its Rack # flashes and the time counts down to 00:00.
• The buzzer sounds. Press the flashing Rack #. Open the door,
door displays. Remove the
product, close the door. Repeat from ✣ until all Rack #'s are done.
To Display the Actual Oven Temperature
• PressandholdtheTemperaturebuttonfor3secondstodisplay ActualOvenTempuntilreleased.
To End a Cooking Cycle
At the end of a cooking cycle, the alarm will sound. To silence the alarm and end a Menu Item cooking
cycle, press START / STOP. To silence the alarm and end a Rack # cooking cycle, press the Rack #.
To cancel a cooking cycle which might have been started in error, press and hold the Rack button to
be terminated and press START / STOP at the same time.
Door and Timing
Opening the door while loading additional product will interrupt all timing functions until the door is
closed and the timer resumes. For example, if a product time had diminished to 1 minute and the door
was opened for 30 seconds and then closed, the timer would still show 1 minute.
SETTING THE OVEN FOR ROAST & HOLD
• Press the Roast & Hold button to select Roast & Hold.
• Set the first stage Temperature and the Cook Time as described in: MANUALLY SETTING THE
TEMPERATURE AND COOK TIME. Press START / STOP to begin cooking.
*
The HOLD Temperature is preset by the computer control at 150 ° F (66 ° C) .

– 17 –
ROAST AND HOLD OPERATION — GCO2C OVEN
Roast and Hold cooks the product in two stages. During First Stage Cooking, the oven temperature is
regulatedbytheRoast thermostatfortheamount oftimeseton theTimer.Afterthe lapsedtimecounts
down to 00:00, Second Stage Cooking begins. During Second Stage Cooking, the burners are off as
the temperature in the oven declines to the Hold Temperature. The door should remain closed during
Second Stage Cooking.
WhentheHoldtemperatureisreached,cookingisdone.TheTimeDisplaycountsuptheHoldtimeand
flashes "Hold." Temperature in the oven will be maintained at the Hold temperature until the oven is
turned off.
400ºF
300ºF
200ºF
100ºF
ROAST AND HOLD DIAGRAM - Time vs. Temperature
SHORT BEEP.
TIMER DISPLAY FLASHES 00:00.
ROAST THERMOSTAT OFF.
BURNERS OFF UNTIL HOLD
TEMPERATURE IS REACHED.
LONG BEEP (20 SEC.)
BURNERS MAINTAIN
HOLD TEMPERATURE.
TIMER DISPLAY COUNTS UP
HOLD TIME AND FLASHES
"HOLD."
OVEN TEMPERATURE
TIMER DISPLAY COUNTS DOWN,
COLON FLASHES.
COOKING FROM
STORED HEAT
LOAD PRODUCT
INTO OVEN
PRODUCT TEMPERATURE
TEMP.
TIME
PREHEAT FIRST STAGE COOKING SECOND STAGE
COOKING
(DO NOT OPEN
DOORS)
HOLDING
PL-51607
PROPER UTENSILS
Theuseofproperutensilscanenhanceovenoperation.Mediumandlightweightpansarerecommended
since it is more economical to bake with lighter pans.
Meats should be roasted in shallow pans deep enough to hold all juices and allow free air circulation.
CONSERVING ENERGY
• Turn off unused equipment.
• Adjust menu patterns and cooking or baking schedules for optimum equipment use.
• Reducethermostatsettingsinslackperiods sincegasequipmentheatsupandrecovers quickly.
• Preheat only to the required cooking temperature for the specific food, not higher.
• Do not open the oven door unless absolutely necessary. Use the window to observe cooking
progress.
• Keep area around the oven door clean and free of food particles.
• Any obstruction that prevents the door from closing completely will adversely affect oven
efficiency.
OPERATING HINTS
When using the convection oven for the first time with a particular food, check the degree of doneness
periodically before the suggested time has lapsed to make sure the desired doneness is achieved.
Record your temperature and time settings for various products. The convection oven can provide
consistent, repeatable results.

– 18 –
The convection oven is a bit faster than conventional deck-type ovens; temperature settings are lower
and cook times are shorter. Since recipes and foods are subject to many variations and tastes, the
guidelines regarding times and temperatures in this manual are SUGGESTIONS ONLY. Experiment
withyourfoodproductstodeterminethecookingtemperaturesandtimesthatgiveyouthebestresults.
CLEANING
WARNING: DISCONNECT THE ELECTRICAL POWER SUPPLY AND PLACE A TAG AT THE
DISCONNECT SWITCH INDICATING THAT YOU ARE WORKING ON THE OVEN BEFORE CLEANING.
Clean outside of the oven daily by wiping with a clean damp cloth.
Clean porcelain oven interior daily with soap or detergent and water. Rinse thoroughly and wipe dry
with a soft clean cloth.
Optional Stainless Steel Oven Interior
Soapordetergentandwaterusuallyhandleroutinecleaning.Rinsethoroughlyanddrywithasoftclean
cloth.
For burned-on foods and grease which resist simple soap and water cleaning, an abrasive cleanser
(scouring powder) mixed into a paste may be used. Apply with stainless steel wool or sponge, always
rubbing with the "grain."
This treatment is equally effective for "heat tint" (slightly darkened areas caused by oxidation). Again,
remember to rub in the direction of the polish lines. Rinse with clear water and dry with a soft cloth.
SUGGESTED COOKING GUIDELINES — MODELS GCO2D AND GCO2C
BAKED PRODUCTS
Product Temp. Time (min.) No. Shelves
°F(°C)
Sheet Cakes (5 lb. each) (2.3 kg) 300 (149) 30 5
Soda Biscuits 325 (163) 12 5
Yeast Rolls 325 (163) 15 – 20 5
Corn Bread 300 (149) 15 5
Gingerbread 300 (149) 18 3
Chocolate Cake 325 (163) 20 5
Chocolate Chip Cookies 325 (163) 10 5
Sugar Cookies 326 (163) 12 5
Yellow Cake 300 (149) 25 5
Angel Food Cake 275 (135) 25 5
Brownies 350 (177) 15 – 20 5
Apple Turnovers 350 (177) 20 – 25 5
Cream Puffs 300 (149) 25 – 30 5
Apple Pie (Fresh) 350 (177) 30 5
Pumpkin Pie 275 (135) 40 5
Berry Pies (Frozen) 325 (163) 40 5
Fruit Pie (Frozen) 325 (163) 45 5
Pizza (Individual, Frozen) 310 – 325 (154 – 163) 8 – 13 5
(Precooked Crust)
Bread (1 lb. loaf) (454 gr.) 340 (171) 30 3
Brown and Serve Rolls 350 (177) 15 5
Coffee Cake 300 (149) 45 3
Pineapple Upside Down Cake 325 (163) 30 5
Fruit Cobbler 375 (190) 25 5
Danish Pastry 325 (163) 12 – 15 5
Pie Shells 350 (177) 12 5
Cinnamon Buns 325 (163) 15 – 20 5

– 19 –
FOR BEST RESULTS
Product to be cooked should be centered on the oven rack, and the racks should be spaced evenly
inside the oven.
It is best not to rotate the product or open the door during the cooking cycle.
Preheat the oven to 50 F°(28 C°)higher than desired cooking temperature. After the oven is loaded,
close the door and set thermostat to desired cooking temperature.
Make adjustments in the time and temperature settings until the desired results are obtained. Adjust
only one setting at a time. For example, if the product is too dark on the outside and not done on the
inside, the oven is too hot. Reduce the temperature by 25 F°(14 C°).
Thesecookingchartswillbehelpfulinarrivingattimeandtemperaturesettingsforproductscommonly
cooked in convection ovens, but it may be necessary to make adjustments in the settings until the
desired results are obtained.
When the desired results are obtained, make a note of the settings used for a particular recipe and
product load. For example, if four 18 x 26" (45.7 x 66 cm) sheet cakes using 5 lb. (2.26 kg) of batter for
each cake, constitutes a typical product load and the size of the load is changed, the final results may
be affected. If either the weight of the cakes being baked or the number of cakes being baked at one
time changes, it may be necessary to make further adjustments in the time or temperature settings to
achieve the desired results.
MEAT & FISH PRODUCTS
Product Temp. Time (min.) No. Shelves
°F(°C)
Prime Rib (20 lb. rare) (9.1 kg) 250 (121) 23⁄4Hr. 2
Rolled Roast Beef 275 (135) 21⁄2Hr. 2
Veal Roast Boned (15 lb.) (6.8 kg) 275 (135) 21⁄2Hr. 2
Stuffed Pork Chops 300 (149) 25 – 30 3
Lamb Chops 375 (190) 12 5
Steamship Round (80 lb.) (36.3 kg) 275 (135) 23⁄4Hr. 1
Meatloaf 325 (163) 40 3
Hamburger Patties (4 oz.) (113 gr.) 400 (204) 8-10 5
Meat Pot Pies 350 (177) 40 5
Chicken Parts 300 – 325 (149 – 163) 30 – 40 5
Fish Sticks 350 (177) 18 5
MISCELLANEOUS PRODUCTS
Product Temp. Time (min.) No. Shelves
°F(°C)
Macaroni & Cheese 350 (177) 30 3
Cheese Sandwiches 375 (190) 10 5
Baked Potatoes (6 - 8 oz.) (170 - 227 gr.) 400 (204) 45 5
Baked Potatoes (10 oz.) (283 gr.) 400 (204) 55 5
Stuffed Peppers 350 (177) 20 5
Scalloped Potatoes 325 (163) 35 5
Lasagna 250 (121) 90 3

– 20 –
FORM 30975 Rev. C (Aug. 2000) PRINTED IN U.S.A.
MAINTENANCE
WARNING: THE OVEN AND ITS PARTS ARE HOT. USE CARE WHEN OPERATING, CLEANING,
OR PERFORMING ANY MAINTENANCE.
WARNING: DISCONNECT THE ELECTRICAL POWER SUPPLY AND PLACE A TAG AT THE
DISCONNECT SWITCH INDICATING THAT YOU ARE WORKING ON THE OVEN BEFORE
PERFORMING ANY MAINTENANCE .
LUBRICATION
The fan motor comes with sealed bearings and requires no lubrication.
The door hinges and mechanism require occasional lubrication with mineral oil.
DISCONNECTING THE GAS LINE RESTRAINT
Ifthis ovenis placedon casters,it shouldbe connectedto thesupply pipingwith theproper disconnect
deviceandrestraint.Ifitisnecessarytodisconnecttherestraint,firstturnoffthegassupply.Reconnect
the restraint before turning the gas supply on and returning the oven to its original installed position.
VENT
Annually check the flue, when cool, to be sure it is free of obstructions.
TROUBLESHOOTING
If the NO IGNITION LIGHT remains lit for more than 20 seconds after three trials (Model GCO2D), or
if E-05 displays after three trials (Model GCO2C):
• Turn oven off for 5 minutes before attempting to re-light.
• Check gas supply valves to be sure they are open.
• Check electrical power source and connections.
• Call your local Vulcan authorized service representative.
SERVICE AND PARTS INFORMATION
Toobtain serviceand parts informationconcerning thisoven, contactthe Vulcan-HartService Agency
in your area (refer to listing supplied with the oven), or Vulcan-Hart Company Service Department at
the address or phone number shown on the front cover of this manual.