Vulcan-Hart FC-500VC User manual

QUICK SETUP GUIDE
FC-500VC
A PRECISION FOCUS

Transfer tube x 1set
Stand legs x 1set Beams x 2pcs Beam cover x 1pc
Right
Left
Power cable x 1pc USB cable x 1pc Ethernet cable x 1pc
Blade holder x 1pc Pen calibration tool x 2pcs Creasing tool x 1pc
Creasing head x 1pc
Blade x 1pc Pen x 5pcs
Relief value x 1pc Silencer x 1pc Transfer hose x 1pc
Accessories list
Hex Key x 1pc Phillip Screwdriver x 1pc
M6 Hex screw x 12pcs
M4 Phillip screw x 4pcs
Accessories for flatbed cutting plotter
Accessories for air pump
Accessories for floor stand

(1) (2) (3)
1:Stand installation
Air pump Relief value Transfer hose
Silencer
Transfer tube
2:Air Pump installation
(1) First,connect "Transfer tube" into "Air pump" and tighten it.
(2) Second, connect "Relief value" into "Transfer tube (on the top)" and tighten it; connect "Silencer" into " Air pump"
and tighten it.
(3) Finally, Connect "Transfer hose" into "Transfer tube(on the right) and tighten it; connect "Transfer hose" to machine
and tighten it.
Note: The transfer hose need to be passed through beam cover.
(1) First,install beams to stand legs, hex screws(8) and hex key be used.
(2) Second,install beam cover onto beams, phillip screws(4) and phillip screwdriver be used.
(3) Finally, Put machine on floor stand, hex screws(4) and hex key be used.
Note: please check labels on machine and stand, to ensure correct direction and positon.
The feet of the machine are movable.As shown,turn left and the wheels will be lifted,
the feet are fixed. Turn right, the feet are lifted, and the wheels can move.
(1) (2) (3)
Stand legs
(each for left and right) Hex Key Phillip Screwdriver
M6 Hex screws M4 Phillip screws
Beams Beam cover
RightLeft
Left Left
M6 Hex screws x 8 M6 Hex screws x 4
M4 Phillip screws x4
The screw pattern of the silencer is very sharp.
Wear gloves when installing to prevent scratches.
!
caution
The blue tube is for easy installation
of the transfer hose. When installing,
please unscrew the blue tube

blade holder cap blade holder
blade
(1) First,unscrew the blade holder cap,as shown.
(2) Second,place the blade (as shown) into the slot of the blade seat.
* There are two types of blade: ordinary blade and circlip blade. Each type is divided into multiple angles,
Here is an example of a general blade.
(3) Finally, screw the blade holder cap to complete the installation and replacement of the blade.
* The length of the blade is also adjusted by the blade holder cap.
(1) First,unscrew the Calibration tool cap,as shown.
(2) Second,place the pen (as shown) into the slot of the pen seat.
(3)Finally, screw the Calibration tool cap to complete the installation and replacement of the pen.
Calibration tool capCalibration tool
pen
3:Blade holder installation
4: Calibration tool installation
(1) (2) (3)
(1) (2) (3)
When pushing the tool holder with your fingers,the blade tip may be protruding.
Take care not to cut your fingers.
!
caution

(1) Step1,unscrew old creasing head.
(2) Step2,Install new creasing head into creasing tool.
7: Control Panel
(1) (2)
(1) (2) (3)
1
2
3
4
5
(1) Acceleration display ......Arrow key speeds for carriage control, Fast (x10) / Slow (x1).
(2) Carriage coordinates......The coordinates of carriage on the table.
(3) Arrow keys.........................To move carriage to different positions.
(4) Speed.............................Carriage moving speeds (tool1/tool2) during working.
(5) Force..............................Carriage down forces (tool1/tool2) during working.
(6) Cancel............................Cancel the job after the work is paused.
5: Replace the creasing head
6: Attaching a tool
Carriage Head
Tool holder 1
Tool holder 2
Tool holder screaw
Tool cover
...
(1) First,Loosen the tool holder screw.Release tool cover.
(2) Second,while pushing up the tool holder, push the tool into the holder until the flange of tool completely
touches the upper part of the holder
(3) Finally, make sure that the tool bracket is engaged on the tool's flange, and then tighten the screw.
6

(1) Tool carriage .................Part to drive the cutter/pen
(2) Y Bar...............................Holds the tool carriage; moves left/right
(3) Storage box....................Placing tools such as knives, holders, pen holders, etc.
(4) Control panel..................Used to access various cutting plotter functions.
(5) Emergency stop switch...In an emergency, the power can be cut quickly.
(6) Stand..............................Stand for supporting the machine.
(7) Air pump........................ Adsorption. Fix the material on the platform.
(8) Power switch..................Used to turn the cutting plotter on and off.
(9) AC line inlet....................Inlet where the power cable is connected.
(10) Network (LAN) interface connector
..................The connector used when connecting this cutting plotter with the network
(LAN)interface cable.
(11) USB memory dedicated port
................The port that is used only for the USB memory.
(12) USB interface connector
................Used to connect the cutting plotter to the computer with a USB interface cable.
(13)Air pump port...............Port that connects the air pump to the machine.
1
2
6
3
4
5
7
9
8
10 11 12 13
8:Product Introduction
Setting.................................Machine calibration and system information.
Speed/Force .............. ....... To set speed/force of tool1/tool2.
Vacuum..................................To toggle of vacuum suction, ON - fast/stable hold, OFF - easy replacement of next item.
Test cut.....................................To cut one square and one triangle for testing force of tool1/tool2.
Pause..................................To pause the cutting job when we find anything wrong.
Files.....................................To choose file from USB-disk (PLT-files saved on USB-disk can be used for direct output).
Recut...................................To repeat last job.
Move to origin......................Return to origin by pressing the single key.
Origin..................................To set work origin.