Vynco OLSEN445E User manual

INSTALLATION INSTRUCTIONS
AUCKLAND
9 Levene Place, Mount Wellington
PO Box 12 249, Penrose, Auckland 1061
New Zealand
P [phone] F [phone]
VYNCO INDUSTRIES (NZ) LIMITED
CHRISTCHURCH
388 Tuam Street, Phillipstown, Christchurch, 8011
PO Box 9022, Tower Junction, Christchurch 8149
New Zealand
P [phone] F [phone]
E [email protected]
VYNCO.CO.NZ
INSV0048
WARRANTY
This product is covered by the standard 3 Year Vynco
Warranty - proof of purchase is required. Please
contact Vynco for details of returns procedure.
NOTE: This product contains NO user serviceable parts.
OLSEN445E - 4FT EMERGENCY DUAL COLOUR INTERIOR BATTEN
SAFETY
Turn off power before installation or before doing
any maintenance work.
Turn off power before setting or changing CCT
colour mode switch.
Do not install any luminaire near a heat source.
For indoor use only. Do not install this luminaire
in damp or wet locations.
Do not exceed the nominal supply voltage or
amperage ratings.
Take care not to pull any electrical wires during
unpacking as this may damage the connection.
Lay out all the components on a smooth surface
and make sure there are no components missing
before assembling.
To avoid injury or damage to the tting, please
ensure that power leads and screws are secure
before connecting the power.
This product should be installed by a suitably
qualied person in accordance with Australian
and New Zealand wiring rules.
IP20
REVISIONS
REVISION DATE
FINISH:
MATERIAL:
REVISION:
DESCRIPTION:
SHEET 1 OF 1
A3
SIZE
APPROVED BY:
PART No:
388 Tuam St
Christchurch
New Zealand
P: 03 379 9283
W: vynco.co.nz
UNLESS OTHERWISE STATED ALL DIMENSIONS ARE IN MILLIMETRES
ALL CRITICAL TOLERANCES SPECIFIED IN DRAWING
NON SPECIFIED TOLERANCES:
LINEAR: 0.0 ±0.5 0.00 ±0.1 ANGULAR: ±0.5°
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF VYNCO INDUSTRIES
(N.Z.) LTD. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION
OF VYNCO INDUSTRIES (N.Z.) LTD IS PROHIBITED.
DRAWN BY:
DRAWN DATE:
CHANGE BY:
CHANGE DATE:
APPROVED DATE:
- - - XXXX
XXXX
XXXX
XXXX
soppitb
17/05/2019
-
-
17/05/2019
XXXX
DRAWING NOT TO SCALE
SPECIFICATIONS
Input Voltage 100 - 240V AC
Power 40W
Lumens 4000 - 4400lm
Emergency Power 4W
Emergency Lumens 400lm
LED Lifetime Hours 50,000
Emergency Run Time 3 Hours
Battery Pack Lithium Iron Phosphate
Battery Pack 6.4V 3Ah
Temperature Range -20 to 45°C
Colour Temperature 4000K / 5700K
IK Rating IK08
Dimensions 1200 x 71 x 68mm
EMERGENCY TEST PROCEDURE
1. L - LIVE is off
2. LSW - EMERGENCY is live
3. The green LED indicator will be ON
4. Press the TEST BUTTON to test the function of
the emergency light. The light should turn ON
and remain ON while the TEST BUTTON is pressed.
The green LED indicator will turn off while the
TEST BUTTON is pressed.

INSTALLATION INSTRUCTIONS
VYNCO.CO.NZ
OLSEN445E - 4FT EMERGENCY DUAL COLOUR INTERIOR BATTEN
STEP 10
STEP 8 STEP 9
STEP 4
STEP 5 STEP 6 STEP 7
STEP 3
STEP 1
STEP 1
Isolate mains power.
STEP 2
Press snap-on buttons and remove diffuser.
STEP 3
Unplug power connection.
STEP 4
Feed mains cable through grommet in base tray /
conduit side entry according to desired application.
STEP 5
Mark and drill xing holes.
STEP 6
Securely x base to the ceiling.
STEP 7
Terminate mains cable into terminal block
and securely clamp.
STEP 8
Connect the DC plug, select colour temperature.
STEP 9
Fix cover to base and ensure all 4 clips engage.
STEP 10
Restore mains power and test to ensure
correct operation.
INSTALLATION PROCEDURE
STEP 2
STEP 2
LSW
LSWITCHED
EARTH
NEUTRAL
N
EMERGENCY /
SWITCHED ACTIVE