WAC Lighting 8011 User manual

WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JANUARY 12, 2016 6:35 PM
waclighting.com
Phone [phone]
Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
1
SAFETY INSTRUCTION
IMPORTANT: NEVER attempt any work without shutting o the electricity.
• Read all instructions before installing.
• System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local regulations.
• Place the wall switch in the“OFF”position.
• Go to the main fuse box, or circuit breaker. Unscrew the fuse(s) or switch ”OFF”the circuit breaker switch(es) that control the power to the
space that you are working on.
CAUTION:
All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out
or broken. Failure to follow this instruction could invalidate the ETL/cETL listing of this xture.
AVERTISSEMENT
IMPORTANT : COUPEZ L’ÉLECTRICITÉ AVANT TOUTE MANIPULATION.
• Lisez toutes les instructions avant d’installer.
• Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les règlements locaux.
• Placez l’interrupteur mural en position d’arrêt (« OFF »).
• Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt (« OFF »).
MISE EN GARDE
Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté et ne les
utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/cETL du luminaire.
THIS INSTRUCTIONS APPLY TO THE MODELS BELOW:
INSTALLATION INSTRUCTION
Landscape 12V Outdoor Tape
8011/8051/8101
8011
8051
8101
8000
*Note: Transformer is required to power the xture. (sold separately)

WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JANUARY 12, 2016 6:35 PM
waclighting.com
Phone [phone]
Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
2
LANDSCAPE 12V OUTDOOR
• Determine the installation area and material, based on dierent mounting materials (wood or concrete), dierent mounting
accessories will be needed.
WIRING AND INSTALLATION:
Please refer to installation diagrams shown on next page.
1. Determine the number of separately powered runs needed. Calculate the number of power supplies.
Min. / max. tape run length 1ft / 40ft per run
Current 180 mA/ft
Power consumption 2 Watts/ft
Input 9-15V AC
Fuse amperage 5A
2. Measure the length of each run and round it o to the nearest 1 foot interval.
Determine the necessary quantities of 1ft, 5ft, and 10ft sections, joiner cables and X or Y connectors.
Note: Tape light may be eld cut every 1 inch at end of run.
3. Connect external power supply to lead wire in accordance to power supply specications.
4. Connect output female connector of the lead wire with the male connector of the landscape 12V outdoor tape or connector.
5. Male/Female connectors of each InvisiLED component can be connected together to form a run.
6. Terminate each separately powered run with an end cap. Install the end cap with silicon ensuring watertight seal.
1"
INSTALLATION INSTRUCTION
Landscape 12V Outdoor Tape
8011/8051/8101
Tape section:
Male
Connector
1w”
1m”
s”
w”
8011 - 1’
8051 - 5’
8101 - 10’
800-06BK - 6”
800-10BK - 10”
Female
Connector
Lead wire with fuse:
6”

WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JANUARY 12, 2016 6:35 PM
waclighting.com
Phone [phone]
Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
3
SAMPLE LAYOUT
A External Power Supply
B 800006/10 6 or 10 ft lead wire with fuse
C 8011/8051/8101 1, 5, or 10ft tape section
D 8003 X Connector
E 8002 Y Connector
F LEDTO24EC End Cap
HARD WIRE A
B
C
D
E
F
INSTALLATION INSTRUCTION
Landscape 12V Outdoor Tape
8011/8051/8101
800006/10
8011/8051/8101
8003
8002
LEDTO24EC

WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JANUARY 12, 2016 6:35 PM
waclighting.com
Phone [phone]
Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
4
1. INSTALLATION CHANNEL LEDTO24CH1/5
at surface, exaple: wood
2. CLIP 1 LEDTO24C1
- Suitable for non-at installation surface, wood or concrete.
- Installation surface have space for the two mounting screw holes.
- No edge contact installation requirement.
3. CLIP 2 LEDTO24C2
- Suitable for non-at installation surface, wood or concrete material applicable
- Suitable for single tape edge contact installation
4. CLIP 3 LEDTO24C3
- Suitable for non-at installation surface, wood or concrete material applicable
- Suitable for double tape edge contact installation.
ACCESSORIES
INSTALLATION INSTRUCTION
Landscape 12V Outdoor Tape
8011/8051/8101
1ft or 5ft