WAC Lighting BA-LIX User manual

WAC Lighting
www.waclighting.com
Phone [phone] • Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive • Port Washington, NY 11050
Phone [phone] • Fax [phone]
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone [phone] • Fax [phone]
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. MAY, 2014
INSTALLATION INSTRUCTION
Premium Xenon Light Bars
BA-LIX
SAFETY INSTRUCTION
IMPORTANT: NEVER attempt any work without shutting o the electricity.
• Read all instructions before installing.
• Always turn o power at fuse box prior to installation to prevent electrical shock.
• For display wall or under cabinet only. Not intended for ceiling use.
• For installation by a qualied electrician.
• System is intended for installation in accordance with National Electric Code, and local regulations.
Consult with local inspector to assure compliance.
• Keep away from combustible materials such as plastic or paper products.
• Do not touch cover when light is on. Do not operate with missing or damaged lens.
• All wires must be contained.
WIRING AND INSTALLATION
1. Remove the two screws securing the cover plate and set it aside.
2. Undo the two nuts securing the inner plate and remove it.
3. Open a convenient knock out hole in the body of the xture, and install the Romex /BX connector supplied with the
xture. Allow approx 1 ½” of wire to enter the xture body.
4. Locate the individual black, white and yellow/green wires with ”poke home” connectors on the ends. Trim ¼” of insulation
from the building wires and connect by pushing into one of the available holes in the connector.
5. Join the black building wire to black xture wire.
6. Join the white building wire to white xture wire.
7. Connect green building ground wire (may be bare copper) wire to yellow green xture wire.
8. Tuck wires connections neatly between the wiring partition.
9. Mount the xture to the surface using screws provided.
10. Replace the inner plate and cover plate.

WAC Lighting
www.waclighting.com
Phone [phone] • Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive • Port Washington, NY 11050
Phone [phone] • Fax [phone]
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone [phone] • Fax [phone]
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. MAY, 2014
INSTALLATION INSTRUCTION
Premium Xenon Light Bars
BA-LIX
WIRING OF MULTIPLE UNITS:
In addition to hard wiring, components are provided to allow xtures to be joined through surface wiring.
Note: The total wattage of all connected xtures should not exceed 700 watts.
END TO END CONNECTION ( I-CONNECTOR INCLUDED ):
The “I” connector allows two xtures to butted end to end.
1. Pry out the plastic covers concealing the female connection ports at the end of the xtures.
2. The “I” connector will only t in the correct orientation.
3. Insert one end of the “I” connector into the xture. Slide the next xture to abut the original.
4. Secure position by mounting xtures to the surface.
INTERCONNECTING FIXTURES WITH JUMPER WIRE (SOLD SEPARATELY):
A surface mount jumper wire allows multiple units to be linked through surface wiring (see diagram below).
1. Pry out the plastic covers concealing the female connection ports at the end of the xtures.
2. Jumper wire ends will only t in the correct orientation.
3. Insert the ends of the connectors into each xture.
4. Jumper wires use metal strain relief cover brackets. Slide the cover bracket over the connector. Position bracket and xture
holes and secure with screw provided.
5. Wrap excess wire with nylon wire ties.
CORD AND PLUG USE ( SOLD SEPARATELY ):
Install the connector end of plug in line cord as described above (using a Jumper wire).
TO RE-LAMP:
• Turn o xture and allow it to cool before replacing lamp.
• For use with Xenon (not tungsten halogen) G8 bi-pin 110 Volt 25 Watt lamps.
1. Remove the two screws securing the cover plate.
2. Lift the cover plate to expose the lamps.
3. Withdraw the lamp by pulling away from the ceramic socket base.
4. Re-lamping is the reverse procedure.