Wacom INTUOS - FOR MACINTOSH User manual

Navigation
Contents
Index
USER’S MANUAL FOR MACINTOSH
®
USER’S MANUAL FOR MACINTOSH
®

Page 2
Contents
Index
Wacom Intuos  User’s Manual for Macintosh

, May 22, 2000
English V3.1 for Macintosh
Copyright  Wacom Company, Limited, 2000
All rights reserved. No part of this manual may be reproduced except for your express personal use. Wacom reserves the right
to revise this publication without obligation to provide notification of such changes. Wacom does its best to provide current and
accurate information in this manual. However, Wacom reserves the right to change any specifications and product
configurations at its discretion, without prior notice and without obligation to include such changes in this manual.
TRADEMARKS
Wacom is a registered trademark. Intuos,Tool ID, QuickPoint, DuoSwitch, and DualTrack are trademarks of Wacom Company,
Limited. Acrobat  Reader Copyright  1987-2000 Adobe Systems Incorporated. All rights reserved. Adobe, Acrobat, and
Photoshop are trademarks of Adobe Systems Incorporated which may be registered in certain jurisdictions. Apple, the Apple
logo, and Macintosh are registered trademarks of Apple Computer, Inc., registered in the U.S. and other countries. Any
additional company and product names mentioned in this documentation may be trademarked and/or registered as
trademarks. Mention of third-party products is for information purposes only and constitutes neither an endorsement nor a
recommendation. Wacom assumes no responsibility with regard to the performance or use of these products.

Page 3
Contents
Index
RADIO AND TELEVISION INTERFERENCE
The equipment described in this manual generates, uses, and can radiate radio-frequency energy. If it is not installed and used
properly—that is, in strict accordance with Wacom instructions—it may cause interference with radio and television reception.
FCC NOTICE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation.
You can determine whether the tablet is causing interference by powering it off. If the interference stops, it was probably
caused by the tablet.
If your tablet does cause interference to radio or television reception, you may be able to correct the interference by using one
or more of the following measures:
• Rotate the television or radio antenna until the interference stops.
• Move the tablet farther away from the television or radio.
• Plug the tablet and computer into an outlet that is on a different circuit from the television or radio.
If necessary, consult your Wacom dealer or an experienced radio/television technician for help.
Changes or modifications to this product not authorized by Wacom could void the FCC Certification and negate your authority
to operate the product.

Page 4
Contents
Index
CE DECLARATION
The Intuos  digitizing tablets, models GD-0405-A, GD-0608-A, GD-0912-A, GD-1212-R, GD-1218-R have been tested by the
WAVE Corporation in Japan, and models GD-0405-U, GD-0608-U, GD-0912-U, GD-1212-U, and GD-1218-U have been tested
by theTokin Corporation in Japan and found to comply to the following harmonized European Norms:
• EN 50082-1 (electromagnetic immunity)
• EN 55022 Class B (electromagnetic emissions)
The Wacom power adaptors have been tested by their manufacturers and found to comply to the following harmonized
European Norms:
• EN 50082-1 or EN 55104 (electromagnetic immunity)
• EN 50081-1 or EN 55014 (electromagnetic emissions)
• EN 60742 (safety of low voltage devices)
Based on the results of these tests,Wacom declares that the above mentioned devices conform to Article 10.1 of the European
Council Directive 89/336/EEC and to the European Council Directive 73/23/EEC, and indicates this conformity by the CE-sign
on each device.
The device must be installed and operated always in strict accordance to the instructions given in this handbook. Any changes
or modifications to this product that were not specifically authorized by Wacom will invalidate this declaration.

TABLE OF CONTENTS
Page 5
Contents
Index
TABLE OF CONTENTS
Using the Pen 29
Holding the Pen 29
Pointing 30
Clicking 31
Using the Side Switch 32
Dragging 33
Proximity 34
Drawing with Pressure 35
Drawing with Tilt 36
Erasing 37
Eye-Hand Coordination Exercise 38
Using the Airbrush 39
Holding the Airbrush 40
Using the 4D Mouse 41
Setting Right- or Left-Handed Operation 42
Using the 4D Mouse Thumbwheel 43
Using the Lens Cursor 44
Caring forYour Tools and Tablet 45
Replacing the Pen or Airbrush Tip 46
CUSTOMIZING 47
Opening the Control Panel 48
Control Panel Features 49
Tabs 50
Control Panel Lists 52
Control Panel Buttons 53
Trademarks 2
Radio and Television Interference 3
FCC Notice 3
CE Declaration 4
About the Manual 8
Navigating the Manual 10
INSTALLATION 11
ADB Tablet Installation 12
Serial Tablet Installation 13
USB Tablet Installation 14
iMac Requirements 15
Uninstalling the Software 16
Registration 16
Product Information 16
USING INTUOS 17
Appearance and Features 18
Intuos 4x5 Tablet 18
Intuos 6x8 and 9x12 Tablets 19
Intuos 12x12 and 12x18 Tablets 20
Intuos Tools 21
Setting UpYour Work Area 24
Working with the Tablet 25
Adjusting the Pen Stand 25
Adjusting Tablet Incline 26
Using TheTablet Menu Strip 27

TABLE OF CONTENTS
Page 6
Contents
Index
CustomizingYour Tools 54
Pen and Airbrush Tabs 54
4D Mouse and Lens Cursor Tabs 55
Adjusting Tip Feel 56
Adjusting Double-Click 57
Customizing Tool Buttons 58
Button Functions 59
Airbrush Settings 64
Adjusting Eraser Feel 65
Customizing Tilt Sensitivity 66
Tablet to Screen Mapping 67
Positioning Mode 69
Orientation 70
Aspect 71
Tablet Area 72
Display Area 75
Customizing the 4D Mouse and Lens Cursor 76
Programming the 4D Mouse and Lens Cursor 77
UsingYour 4D Mouse as a 15-Button Mouse 77
Creating a Button Box 79
Customizing the 4D Mouse Thumbwheel 80
Customizing the Pop-up Menu 81
Add Macros 82
Add Keystrokes 82
Add Mapping Options 82
Removing Pop-up Menu Options 82
Customizing Tablet Buttons 83
Working with Multiple Tools 85
Adding a NewTool 86
Using More Than OneTool 87
Working with Application-Specific Settings 88
Creating an Application-Specific Setting 90
Adding Additional Tools to an Application’s Tool List 92
Changing Settings for a Specific Application and Tool 93
Removing Application-Specific Settings 93
CheckingYour ADB or USB Tablet Mode 94
CheckingYour Serial Tablet Connection 95
Pull-Down Menus 96
File 96
Edit 96
Add 97
Remove 97
Language 98
Help 98
ADVANCED FEATURES 99
Advanced Tip Pressure Settings 100
Click Force Adjustment 101
Pressure Curve Adjustment 102
Advanced Eraser Pressure Settings 104
Copying Settings 105
Using DualTrack 106
Advanced Mapping 107
HAVING TROUBLE? 112
Troubleshooting 113
Testing ADB Tablets 113
Testing Serial Tablets 114
Testing USB Tablets 115
VerifyingYour Macintosh is USB Ready 116

TABLE OF CONTENTS
Page 7
Contents
Index
Resolving Software Conflicts 117
Using the Extensions Manager 117
Manually Resolving a Conflict 118
TestingYour Intuos Tools 121
Testing a Pen or Airbrush 121
Testing a 4D Mouse or Lens Cursor 123
Troubleshooting Tables 124
ADB Tablet Problems 124
Serial Tablet Problems 125
USB Tablet Problems 127
General Problems 128
Contacting Technical Support 133
Linking to the Web Page 133
Pre-Contact Checklist 133
Who to Call 134
USA, Canada, Central and South America 135
Europe, Middle East and Africa 136
Japan 137
Asia Pacific (English) 137
APPENDICES 138
Installing Multiple Tablets 139
Product Specifications 140
General Specifications for All Intuos Tablets 140
Intuos 4x5 Tablet (Models GD-0405-A, GD-0405-U) 141
Intuos 6x8 Tablet (Models GD-0608-A, GD-0608-U) 141
Intuos 9x12 Tablet (Models GD-0912-A, GD-0912-U) 142
Intuos 12x12 Tablet (Models GD-1212-R, GD1212-U) 142
Intuos 12x18 Tablet (Models GD-1218-R, GD-1218-U) 142
Intuos Pen (Model GP-300E) 143
Intuos Airbrush (Model GP-400E) 143
Intuos Inking Pen (Model GP-110) 143
Intuos Stroke Pen (Model GP-120) 144
Intuos 4D Mouse (Model GC-500) 144
Intuos Lens Cursor (Model GC-210) 144
Parts and Accessories 145
Ordering Parts and Accessories 145
Tablets 146
Tools 146
Pens 147
Airbrush 147
4D Mouse 148
Lens Cursor 148
Other Parts and Accessories 149
License and Warranties 150
Software License 150
Limited Warranty 151
Warranty on Sales Outside of U.S. and Canada 153
GLOSSARY 154
INDEX 158

Page 8
Contents
Index
ABOUT THE MANUAL
This interactive User’s Manual provides quick access to information about Intuos. Just click on a
navigation button or highlighted word to move through the document. The information is common to all
tablet types (ADB, serial, and USB), unless otherwise noted.
• The Table of Contents enables you to go directly to a topic by clicking on it.
•Installation describes how to install the hardware and software, and how to uninstall the software.
•Using Intuos introduces you to the many capabilities of your Intuos system, including a description of
the various tablet models, and the features and functions of each Intuos tool. This section also
includes exercises for new users.
•Customizing describes how you can change the control panel settings to optimize Intuos tablets and
tools for your personal work style.
•Advanced Features allow further customization of your Intuos Graphics Tablet System. Explore them
after you have become familiar with using Intuos and the basic control panel settings.
•Having Trouble? Need troubleshooting guidelines? Do you have a question for Technical Support?
You will find the answers to most common questions here.
• The Appendices include product specifications, license and warranty information, and a listing of
replacement parts and accessories. If you are using more than one tablet on your computer, you will
find instructions on adding and working with multiple tablets.
If you are new to electronic documentation, be sure to read Navigating the Manual.

Page 9
Contents
Index
S
MALL CAPITAL LETTERS
are used to identify the names of keyboard keys, dialog boxes, and control panel
options.
As you read through the Customizing and Advanced Features chapters, you will notice that the screen
shots of the control panel tabs do not show the tab buttons. These are intentionally left out in order to
save space within the manual.
Remember that you can always use the Acrobat Reader zoom-in tool to increase the size of the manual
on your display screen.
Certain kinds of information are not included in this manual:
• Information about your specific computer hardware.
• Information about your operating system.
• Information about other Wacom tablets.
• Information about application software. Many graphics applications have built-in support for Intuos
features (such as pressure-sensitivity, tilt, airbrush simulation, 3D navigation with the 4D Mouse, and
two-handed input). You can find a listing of applications that support these features at Wacom’s web
site (see Product Information). Refer also to your application manuals for information on how best to
use Intuos features within specific applications.
Your best source for the above information is the set of manuals and disks that came with your hardware,
operating system, applications, or other Wacom tablets.

Page 10
Contents
Index
NAVIGATING THE MANUAL
Use the navigation controls to move through the manual:
Go to front page.
Go to Table of Contents.
Go to Index.
Go back to previous view.
Page back, or page forward.
Go to beginning of section.
Go to topic.
Topic continued.
The Acrobat Reader provides you with additional tools for using and printing the manual. Refer to the
Acrobat Reader Online Guide for more information.
Contents
Index
HEADING TEXT
Topic

INSTALLATION
Page 11
Contents
Index
INSTALLATION
Intuos ADB and serial tablets are compatible with Macintosh systems using Mac OS 7.0 or later, and with
all applications that support a mouse.
USB tablets are compatible with any Power Macintosh equipped with a USB port, and with all applications
that support a mouse. If you have an iMac, you will need Mac OS 8.5 or greater. Refer to the iMac
Requirements for information on running the iMac Update software located on the Intuos CD-ROM.
The Wacom control panel requires a 640 x 480 or larger color monitor for proper display.
ADBTABLET INSTALLATION
SERIALTABLET INSTALLATION
USBTABLET INSTALLATION
UNINSTALLING THE SOFTWARE
REGISTRATION

INSTALLATION
Page 12
Contents
Index
ADB TABLET INSTALLATION
To install your Intuos 4x5, 6x8, or 9x12 tablet:
1. Turn off your computer and plug the tablet connector
into your computer’s ADB communication port. See
2. If you do not have an available ADB port, connect the keyboard to the tablet
cable pass-thru connector. Then connect the tablet cable to the computer. See
3. Turn on your computer. The tablet LED will light to indicate the tablet is powered up.
Important: Temporarily disable any virus protection programs before installing
the software.
4. Insert the Wacom CD into your computer. Double-click on the INSTALL icon.Choose
your language option, click OK, and follow the prompts.
You should now be able to place your Intuos Pen on the tablet to move the screen cursor.
If you had any trouble with this installation, go to Having Trouble?
Each time you start your computer, the Wacom Tablet startup icon tells you if the tablet
driver has successfully loaded.
The driver is loading.
The driver has loaded successfully.
The driver did not load.
The driver loaded, but a Wacom
tablet cannot be found. The tablet
may be unplugged.
B
A
B
A

INSTALLATION
Page 13
Contents
Index
SERIAL TABLET INSTALLATION
To install your Intuos 12x12 or 12x18 tablet:
1. Turn off your computer and connect the
Macintosh serial adaptor cable to the tablet cable. See
2. Connect the AC power cable. See
3. Connect the adaptor cable to your computer’s
serial communication port, either modem or printer. See
4. Connect the Wacom power adaptor into an AC outlet or power strip.
Then turn on the tablet’s power switch. The tablet LED will light.
Important: Turn on your computer and temporarily disable any virus protection
programs before installing the software.
5. Insert the Wacom CD into your computer.
6. Double-click on the INSTALL icon. Choose your language option, click OK, and follow
the prompts.
You should now be able to place your Intuos Pen on the tablet to move the screen cursor.
If you had any trouble with this installation, go to Having Trouble?
Each time you start your computer, the Wacom Tablet startup icon tells you if the tablet
driver has successfully loaded.
The driver is loading.
The driver has loaded successfully.
The driver did not load.
The driver loaded, but a Wacom
tablet cannot be found. The tablet
may be unplugged or turned off.
C
BA
Power Switch
B
A
C

INSTALLATION
Page 14
Contents
Index
USB TABLET INSTALLATION
Intuos USB tablets run in high-speed, high-power USB mode. The tablet must be
plugged directly into a USB port on your computer or into a powered USB hub.
USB ports support hot-plugging so you can connect or disconnect Intuos without
turning off your computer.
If you are using an iMac, refer to the iMac Requirements section before installing
Intuos.
1. Plug the USB connector into a USB port at the back of your computer or into a
powered USB hub. (Do not plug the tablet into a USB keyboard, as the
keyboard is not a powered USB hub.)
2. If your computer is off, turn it on now. The tablet LED will light to indicate Intuos
has registered as a USB device. If the LED does not light, your USB port may
not be functioning properly; go to Having Trouble?
Important: For pressure-sensitivity, you must install the tablet software
from the Intuos CD-ROM. Disable any virus protection programs and close
all open applications before installing the software.
3. Insert the Wacom CD into your computer.
4. Double-click on the INSTALL icon. Choose your language option, click OK, and
follow the prompts.
After restarting your computer, you will be able to use the pen to move the screen
cursor with absolute positioning. If you had any trouble with this installation, go to
Having Trouble? To tablet

INSTALLATION
Page 15
Contents
Index
iMAC REQUIREMENTS
Intuos requires Mac OS 8.5 or greater and Mac OS ROM 1.2.1 or greater.
1. Verify the Mac OS and ROM versions: Click on the Apple icon and select A
BOUT
T
HIS
C
OMPUTER
.... The A
BOUT
T
HIS
C
OMPUTER
dialog box will appear with the OS version displayed in the top right corner. Mac OS 8.5 or greater is required.
If the version shown is older than Mac OS 8.5, contact your local computer dealer to purchase an upgrade.
If Mac OS ROM version 1.2.1 or greater displays under the Mac OS version, your iMac does not need the firmware or OS
ROM update. If it does not appear or an older Mac OS ROM is installed, continue with the instructions below to install the
I
M
AC
F
IRMWARE
U
PDATE
and then install
I
M
AC
U
PDATE
1.1.
2. Install the iMac Firmware Update: In the A
PPLE I
M
AC
U
PDATES
folder located on the Intuos CD-ROM, double-click on the
I
M
AC
F
IRMWARE
U
PDATE
icon. This will decompress the file. Within the open folder that appears on the desktop, double-
click on the
I
M
AC
F
IRMWARE
U
PDATE
icon and follow the prompts. If in doubt, install this update.
3. Install iMac Update 1.1: Install
I
M
AC
U
PDATE
1.1 by double-clicking on the
I
M
AC
U
PDATE
1.1 icon located in the A
PPLE I
M
AC
U
PDATES
folder. This will decompress the file. Within the open folder that appears on the desktop, double-click on the
I
M
AC
U
PDATE
icon and follow the prompts. If in doubt, install this update.
4. After updating your system, perform the USB Tablet Installation.
Each time you start your computer, theWacomTablet startup icon tells you if the tablet
driver has successfully loaded.
The driver is loading.
The driver has loaded
successfully.
The driver did not load.
The driver loaded, but a Wacom
tablet cannot be found. The tablet
may be unplugged.

INSTALLATION
Page 16
Contents
Index
UNINSTALLING THE SOFTWARE
To remove the Intuos software from your system:
1. Insert the Intuos CD-ROM into your computer and double-click on the I
NSTALL
icon.
2. Select R
EMOVE
instead of I
NSTALL
.
REGISTRATION
Please be sure to register your product. Depending on your region, the Wacom tablet may come with a
Registration Card that you should complete and mail, or you may be prompted to register online during the
installation process.
PRODUCT INFORMATION
To learn more about which software applications currently support your Intuos tablet and tools, visit the
Wacom web site for your region:
USA, Canada, Central and South America http://www.wacom.com/productinfo
Europe, Middle East and Africa http://www.wacom.de/productinfo
Japan http://tablet.wacom.co.jp
Asia Pacific (English) http://tablet.wacom.co.jp/asia-pacific

USING INTUOS
Page 17
Contents
Index
USING INTUOS
This section introduces you to the Intuos Graphics Tablet System. If you are new to using a graphics
tablet and tablet input tools, read the following sections. They describe your Intuos tools and explain how
to use them with the tablet.
APPEARANCE AND FEATURES
SETTING UPYOUR WORK AREA
WORKING WITH THETABLET
USING THE PEN
USING THE AIRBRUSH
USING THE 4D MOUSE
USING THE LENS CURSOR
CARING FORYOURTOOLS ANDTABLET

USING INTUOS
Page 18
Contents
Index
APPEARANCE AND FEATURES
The Intuos Graphics Tablet System consists of two basic elements: a graphics tablet that serves as your
work area, and the Intuos Tools you use with the tablet. For a complete listing of Intuos tablets, refer to
Parts and Accessories.
INTUOS 4X5 TABLET
Note:To learn more about your tablet, see Working with the Tablet.
Active Area
Pen Stand
Status LED
Tablet Overlay
Cable
Menu Strip

USING INTUOS
Page 19
Contents
Index
INTUOS 6X8 AND 9X12TABLETS
Note:The Intuos 9x12 tablet is shown. To learn more about your tablet, see Working with the Tablet.
Menu Strip
(removable)
Active Area
Incline Bar
(shown attached)
QuickPoint Area Markings
(not available for the 6x8
tablet)
Status LED
Tablet Overlay
Cable
Pen Stand

USING INTUOS
Page 20
Contents
Index
INTUOS 12X12 AND 12X18 TABLETS
Note:The Intuos 12x12 tablet is shown. To learn more about your tablet, see Working with the Tablet.
Menu Strip (removable)
Active Area
Pen Stand
QuickPoint Area Markings
Power Switch (serial tablets only)
Status LED
Tablet Overlay
Cable