Wadkin PBR User manual

Modifi~lionl .. e made 10 Ihl'$ll books froin lime 10 time a nd it is impol"lenl
the r e~ore that only the book sent with the machine should be u sed
working manual at a
PLEA SE INSeRT SERIAL NUMBER OF MACHINE
Power Band Rip Saw
SPEX:IFlCATION
Diameter of saw wheals
Ma.x1mu:I depth under sa'\( giidc
l"".aximUm depth of out
M::u;1:rAmI di,tanc. e ea..., to bod<f
I'UmimIlm ,,1dth of bl:We
/1a.ximUl:I width of blade
Max1:IIm lc~ of blade
!'U.mimur:I le!'J6'th of blade
Spoed of motor. 5OH3
Speed of motor. 60Hz
Power of m()tor
Speed of eaw blade'
Ei gh t feed epeeds
Size of tab le
Height of t able
Floor space ( No pit required)
Weieht (Approximately)
Table cants with feed un! t
Table cante wit hout feed unit
OPJ'lOOAL EXTRAS .
A'IJ'I'Q1I,.TIC STAR DEUl'A STARTER.
FINE ADJUS'l'!1ENT TO TABLE CANTING
BY SCREW AND RAND 'iIHEEL.
ELECTRIO INTERLOCK ON FOOl' BRAKE.
SPm' LIGtrrmG EQUIPME:m' .
nIFEED AND OOT?EE:O ROI.Lffi TAllLES.
27 .S1n
191n
121n
26 . 1in
...
~~8in
16!t21
in
3000rev/min
3600rev/min
10Hp
5OOOrt!min
6-98ft/min
)Ox}91n
351n
31 !x6Jin
1 3Jllb
25
0
,5
FOR REPLACirom' PAm'S, TOOlS MIll ACCESSORIES
CQNTACT :- \oIADlON Cu:vEIJillD (Div or Wa.dk1n Ltd)
NORTH LIVEI\'I'ON nm EST
=
SAUTBURN -EY ~SEA
CLEVELAND
""'LAND
(Telephone: Gui s boroUSh 0287/40177)
n
www.wadkin.com
[email protected]

72
POWER
FEED
U NIT
•
. .'
. .
ROllE R
BED
ENeE
www.wadkin.com
[email protected]

DEPl'Il
OF
c'"
eon ',wn
>WID WOOD
NOl'E: - THI S BOOK TO BE USED IN CONJUNCTION
}!ITH THE "C" RANGE BANDSAW Mm AUTa·IATIC
FEEDER rnSTRUCTION BOOK AND ALL IlISTRUCTION
BOOIC3 SHOUIJ) BE IU:AD BEFORE usiNG THE MACHDJE .
FOR OPTIMU;.! BMIlE LIFE THE FOLTflllllIG FEED SPElIDS
m REC lI1J.!FWED.
'"
2"
j tt
4"
6" 8" 10"
98
49
J9 33
20 " "
33
20
" " 6 --
--
MACHINE }1mT BE B OLTED Dam .
73
12" I
,
Fr / Mil l
--
FT/NIN
www.wadkin.com
[email protected]

74
FIG 1
FIG 2
FIG3
FIG 4
NOJ'F,:- Pi~" 1-4 show the pooiUon the Feed Unit can be Bot to accOIrIMdate
various stook si",,,:;,
!!2..!:t:=- The Top Guide should alwn.ya be Dot clooe a,o;; po~sible to the otock .
•
www.wadkin.com
[email protected]

75
>'10.
S.
Top Saw CuidOl (S09 Setting lnstruot1ons)
J >'10. 6.
BottOlU Saw Guide (See Settin8 Ir\lIItl:'\l.CUonu)
>'10.
7.
~neion Indioator
FIG.
8. 'l'racld.rl6' S.... Bl.ade
FIG.
9.
Top Door Open To Allow Removal
Ot Blade
lIG.10 .
Food unit Locks And Ad;!uatment
www.wadkin.com
[email protected]

6
E
7.
,
2
~ -
, ,• )
rf!l
4
5
,
-
B OTTO M SAW GU I DE FIG 6
r
FIG 7 TENS I ONiN[ ~ AJ(
PO S ITIONI NG OF SAW BL ADE FI G8
FIG 10
,
www.wadkin.com
[email protected]

••
FI'l'l'lllG OF RIP SAW Bl'JJ)ES. (See also pace 10 -"C" Banee inotroction book. )
1) Isolate machine el ectrioally .
2) S"ing power feed unit out and open top door together until door ole=
blade eu=d aperture on main colunm of ma.chine•
3) TrnvcrRe roller bed fence to the right h~d side of machine until i t
cle~ Caw slot in t ablo, open bottom door and remove top SaW guard.
II) AdjUllt top wheel sufficient to al l ow blude to be fitted to both wh"el$,
tension r,ml bb.dp until pointer on tension indicator (See f'ig 7, page 9.)
in dicates P.D.R.
5 } Tracking of: the saw bln.dc is done by rotating the top "heel Blowly by hand
in a clockwico d~rec t ion, the root of: the naw tooth ohould ovcrhane t he
rim of the wheel by approximately 2mm (~ee fig'o 8 &1 2) .
Shou2d blade not track correctly , lo ssen wing nut "B", fig 11 then turn
handwheol "C" until caw is tm.cking correctly then tighten wingnut " ll".
FIG 11
n
I
www.wadkin.com
[email protected]

7.
WHEEL
.--~ ... ___ ___ _ - -· h
F
------+-...l.
FIG 12
www.wadkin.com
[email protected]

SAW GUIDES
The top nnd bottom guide Wlits Fie 5 & 6 ~hou.ld be aet up a.s follows
with the top arM ¢d c !Lll elo~" to -th o "toek o.a prac tical. .
1) Loosen grubserew "A" and M10 "B" FiG 13 . thcm position g.Ude body " C"
centnLl and parrelle l to bl.a.de sec Pig 14 , then tighten lip grubserew
"A" and M10 Nut ''11'' .
NOI'E,_ Once the guide brru:ket has been intiaU y ""t up , only the
ndJuatmc nt described in p aragr.aph~ 2 &3 shou ld bo n""cseary .
2) Slacken thumb cerew"Y" Fig 1) , and set near guide roller approxi.!!lately
San 018= of back of hlado:! (Sec Fig 1 $) and lock up thumb screw
SCClU'ely .
3) Sinekcn thumb 3C rcws "X" Fie 13. and move side guide rollers f'ol:'W!1.ri!
a::J positioned in FiS' 1$ , then pivo t sido suJ.-de rollcl:'S on anti lock
ecc'.>ntricIJ until they II-""C just clear of bl.:J.de and lock thumbscrew "X ".
NOl'E;- It is important to check that the side guiee rollc:ro do IlQt nip
tho blade when locked up, and th:!.t the guide Il.l!sembly is square
t o the =tural line of the blade ( se e Fie 16),
79
FI G 14
FIG 13
--
www.wadkin.com
[email protected]

eo
FIG. 15
FIG. 16
ccrn"""
DICORRECT
l
y
,
R
t
,
f
www.wadkin.com
[email protected]

FF.F:Drn IDIl'r . Pi...: 1 1.
Thn fccdtl:t' uni t can opcrate in bot h tlire cti ons and lmt 6 llpceda atininod by :-
A) Two opecd motor with twitc h pogitions 1 and 2.
n) Cear
l~v er with posi tions I end Ir .
C) Int er changinG ge= Noo WI nnd 65.
Tho
feeder un! t should alwaya be opoxated in aeoordaru::o "i th the iru!truction.~
supplied .
Deat reeding :re sul ts are obtained when face of Ieed rolle r.;; XI:'(! parrallo1 to
t1l1lbor.
FIG 17
'C",'-' locldn,g point~ ( Fig 16) OlUSt be ccnurad b"fo1!'e foetling, otherwise
i+-~olr into blade .
NOTF.:- Feedsr will not operate unless
machine i s running .
FIG 18
.,
www.wadkin.com
[email protected]

62
ROLtm EED FrnCf;.
'I'he roller bed fcru:e 1ncol:JlOrate3 an ~tablC! pointer and fine adJ=tmcnt
tlCchanimlll, toguth.:-r wit h secure fe nco lo ck for accu.rate stock control .
(see fig. 19).
The 1nJ:eed brackot (fig. 19) on tho;> fence incorporates 0. feeder settin,s: ~calc
(f:1£. 20) llhich is us&d as follows:-
1) Set fonco to finished lltock size dcsiZ'(ld.
2) ~lea:;ure avcra&'! width of stock to be ri p ped i.e. 100::1;J.,
3) Aligno face of feed rollern to width indicated on feeder setting scale
i.e. 10ClPt!1 .
This aottin,s: methO<l automat1cal.q giVOB S= motoriru; over pre:m'lU'O, (.IlId I\llollll
the Wlit tOacCOIlICladato approxiJ:l<\tely 61:11 stock variance without continu.U
adjuatmcnt of feeder unit .
F IG 20
FIG19
FINE
SETTING
SCALE
www.wadkin.com
[email protected]

GENF.RAL
All machinos ar(! fully tested before leaving our W<lrkB, and e.re not paasGd unless
in parrect working order.
83
They are simple to opera t e but nevertheless care is necessary in their use and the
following inn t ruotions carried out.
1) Machines should be bolted down.
2) The machine should bo:> cOl1l10o te d to = efficient extraction system.
3) The machine should be kept clean and checked da.ily.
4) The handsaw blades should be rngulary maintained, cutting life will depend
on depth and tYl'C of timber being cut.
S) Tho reoo l!llll ended f'eed speeds should not be exceeded.
6) Guide should always be set up oorreotly (see guide setting inatructions).
1)
Blade should alway>! be tensioned and
fitti ng instructions).
tracked correotly. (sea b lade
8) All instruotion books should be read ful ly before operating machine.
9) Always isolate machino eleotrically befo:r;'e oarrying out any adjUiltments
or maintenance .
I
- .
www.wadkin.com
[email protected]