Wagan Elite 1000W PRO User manual

Item No. / Artículo No/ Article n° : 2603
User’s Manual / Manual de Usuario / Guide d’Utilisation
Please visit our website for the latest information on this product.
Visite nuestro sitio web para obtener la información más reciente sobre este producto.
Veuillez visiter notre site Internet pour obtenir les dernières informations sur ce produit.
RoHS
compliant

Elite™ 1000W PRO by Wagan Tech®
1www.wagan.com
INTRODUCTION
Thank you for purchasing the Wagan Tech®Elite™ 1000W PRO Pure Sine Wave
DC to AC Power Inverter. Read and understand this manual before installing and
operating this inverter. Keep this manual for future use.
The "PRO" model represents numerous improvements to our first generation of
Elite pure sine inverters that meet the needs of more demanding environments—
providing clean power at an affordable price. It delivers a true AC sine wave
identical to that of commercial power. Use this inverter to power AC appliances
in your vehicle. Pure Sine Wave AC means that your sensitive electronics, such
as audio/video systems, computers, and communications equipment will operate
properly. Furthermore, appliances with motors operate cooler, quieter, and more
efficiently when they are powered by pure sine wave AC.
The inverter is powered from 12 volt DC and it will continuously deliver 1,000
watts AC power at 120 volts, 60 Hz. Superior surge capability of 2,000 watts
allows the inverter to start most difficult motorized appliances. Advanced
microprocessor-controlled circuits run cooler and are more reliable than
competing units. The Elite™ 1000W PRO operates at high efficiency (up to 90%),
that results in long run time and extended battery life compared to other inverters
with this level of power output. A 2.1A USB power port provides a convenient
way to power USB devices, including tablets, e-readers, smartphones, and other
mobile electronics.
The Elite™ 1000W PRO comes with a separate ground terminal typically found
on higher capacity units. This terminal helps to reduce the noise caused by power
conversion when using radio frequency devices.
For your convenience, this inverter is supplied with a remote control. The installer
must install a fuse and fuse holder for battery protection. See “Configurating
Battery Bank” section.
The DC terminals have been designed apart from each other to ease installation
and minimize the risk of accidental shortage when handling the DC cables. This
inverter bonds neutral to ground, just like utility power. The enclosure vents have
been minimized to reduce the risk of pest intrusion in arid tropical climates.

©2017 Wagan Corporation. All Rights Reserved.
Wagan Tech and wagan.com are trademarks of Wagan Corporation.
User’s Manual—Read before using this equipment
2
The Wagan Elite™ 1000W PRO Pure Sine Wave Inverter is an indispensable
addition to your compliment of mobile power equipment. With minimal care and
proper treatment, it will provide years of reliable service.
SPECIFICATIONS
Output waveform Pure sine wave
Input 12V DC
Output 120V AC
TrueRated Power™1,000 watts (24-hour continuous)
Peak surge 2,000 watts
Efficiency > 90%
Frequency 60Hz
Total harmonic distortion (THD) < 3%
No load current draw < 0.6A
Battery low alarm 10.5V ± 0.5V DC
Battery low shutdown 9.5V ± 0.5V DC
Over voltage shutdown 15.5V ± 0.5V DC
Cooling fan Thermally controlled
AC output sockets 2 North American standard
USB power port 2.1A, 5V ± 0.25V
Power output control AC On/Off Switch
Dimensions 13.4 × 8.1 × 3.5 in.
Net weight (approximate) 9.3 lb
Included DC cable with ring connectors 35.4 in., 8 AWG
* All specifications are typical at nominal line, half load, and 77 ºF (25 ºC) unless otherwise noted.
Specifications are subject to change without notice.

Elite™ 1000W PRO by Wagan Tech®
3www.wagan.com
WARNING
sINVERTER OUTPUT CAN BE LETHAL. IMPROPER USE OF THIS INVERTER MAY
RESULT IN PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.
• Keep the inverter away from any direct heat source or combustible
materials.
• Keep well ventilated—this device generates heat.
• Keep this inverter in a dry environment.
• Do not operate any equipment over 1,000 watts.
• This inverter is designed to operate from a 12 volt DC power source only.
• Do not attempt to connect the inverter to any other power source, including
any AC power source.
• Incorrect battery polarity will damage the inverter and void the warranty.
• Do not open the inverter; there are no user serviceable parts inside.
DISPOSAL/RECYCLING OF INVERTER
Electronic products are known to contain materials that are toxic if improperly
disposed. Contact local authorities for disposal and recycling information.

©2017 Wagan Corporation. All Rights Reserved.
Wagan Tech and wagan.com are trademarks of Wagan Corporation.
User’s Manual—Read before using this equipment
4
FRONT PANEL
Power Switch
AC Outlets
Digital Display Fault LED
USB Power Outlet
Power LED
Ground Terminal
• Power Switch — This switch controls AC output of the inverter.
• Power LED (Green) — When this green LED is lit, the inverter is operating
normally.
• Fault LED (Red) — The RED indicator turns on as the inverter shuts down due
to overheating, overload, under voltage, or over voltage.
Immediately turn off all AC appliances if the FAULT LED is lit. Allow the
inverter to cool before continuing. Make sure that the ventilation vents
are not blocked.
If an inverter shutdown was preceded by a buzzing sound, there may
be an excessive load in combination with a low voltage or cable
problem.
Observe the Digital Display for low battery voltage. Normal
operating range is 11V to 15V DC.
• Digital Display — The digital display alternates between input voltage
and output power (kilowatts). The DC input voltage displayed is what the

Elite™ 1000W PRO by Wagan Tech®
5www.wagan.com
inverter senses at its terminals. Low battery and excessive load for the
cables can cause a low voltage reading and inverter shutdown. Low battery
is also indicated when the audible alarm sounds. The wattage displayed
for the output power is a rough estimate of the load being applied to the
inverter. A multimeter should be used for a more accurate reading of the
load.
• AC Outlets — These outlets can supply up to 8.3 amps at 120V AC 60 Hz
• USB Power Port — This power port can supply 5 volts at 2.1A for charging
or powering tablets, e-readers, smartphones, and other small electronic
devices.
• Audible Alarm (internal to the inverter) — When the Audible Alarm makes
a buzzing sound, the inverter senses a low battery condition. The user
should reduce the AC load, charge the battery, and check the DC cable for
excessive losses.
• Ground Terminal — For attaching an insulated safety ground wire. This
safety wire is for protecting personnel if there is an unlikely failure in either
the cabling or enclosure insulation. Grounding the inverter enclosure
ensures personnel safety should a DC cable problem occur. During the
installation procedure, the Ground Terminal is connected either to a vehicle
chassis or to the negative DC terminal of the battery. Do not directly
connect this ground connection to the negative DC terminal of the inverter.
Use an insulated 10 gauge wire to make the ground connection. If the
inverter installation is located in fixed location, the safety wire can be
connected to earth’s ground.

©2017 Wagan Corporation. All Rights Reserved.
Wagan Tech and wagan.com are trademarks of Wagan Corporation.
User’s Manual—Read before using this equipment
6
REAR PANEL
Positive (+) Terminal
[Red]
Negative (−) Terminal [Black] DC Connector Guard
Cooling Fan
• Positive Terminal — Positive (+) DC Input (Red)
• Negative Terminal — Negative (−) DC Input (Black)
• Cooling Fan — High-speed and load controlled
• DC Connector Guard — Protects your DC cables from accidentally touching

Elite™ 1000W PRO by Wagan Tech®
7www.wagan.com
REMOTE ON/OFF CONTROL
Retracted Antenna
Retractable Antenna
Extended Antenna
On Button
Off Button
Sliding Cap
This inverter is supplied with a 100-foot range, battery-powered, wireless On/Off
remote control. To enable the Remote Switch, the Front Panel Power Switch of the
inverter must be on (in the "|" position).
To turn on the inverter, momentarily press the Unlock button. To turn the inverter
off, momentarily press the Lock button. If the wireless remote fails to control
operation of the inverter, you may be out of range for the radio signal—move
closer to the inverter. If the remote switch has a depleted battery, open the unit
by unscrewing the three small screws on the back side of the remote control and
replace the 12 volt, 23A alkaline battery with a new one.

©2017 Wagan Corporation. All Rights Reserved.
Wagan Tech and wagan.com are trademarks of Wagan Corporation.
User’s Manual—Read before using this equipment
8
LOAD CONSIDERATIONS
The startup load of an appliance is a major factor of whether this inverter
can power it. This initial load is only momentary. With many appliances, it is
approximately twice the continuous load, but some appliance startup loads can
be as high as eight times the continuous load.
The inverter will automatically shut down in the event of an output overload so
there is no danger of damaging either the inverter or the equipment. When the
red LED indicator is lit, the inverter is signaling a fault.
PLANNING THE INVERTER SYSTEM
Any large wattage inverter system requires planning before installation. There are
several steps to the planning process so the user must determine the following:
• Maximum inverter wattage required
• Operating time (run time) needed between battery recharges
• Battery bank capacity in amp-hours
• Charger requirement to charge batteries within a practical time
• Distance between battery bank and inverter
DETERMINING MAXIMUM APPLIANCE WATTAGE
Do not exceed the 1,000 watt maximum AC load or the inverter will shut down.
Most electrical tools, appliances, and audio/video equipment have labels that
list the unit’s power requirements in watts. If the tool or device is rated in amps,
multiply the amps by 120 (120V AC) to determine the watts. For example, an
appliance rated at 0.5 amps will draw 60 watts.
WATTS = VOLTS × AMPS
Remember to consider the startup surge that motorized appliances will cause. Do
not exceed the 2,000 watt momentary surge rating of this inverter. This can cause

Elite™ 1000W PRO by Wagan Tech®
9www.wagan.com
immediate overload shut down and or blow a fuse. The fuse on this inverter is
external and replaceable for this purpose.
CONFIGURING THE BATTERY BANK
To determine the minimum battery ampere-hour rating that you will need to
operate appliances from the inverter and any DC appliances powered by the
battery bank, follow these steps:
1. List the maximum continuous wattage that the inverter has to supply.
2. Estimate the number of hours the appliances will be in use between battery
recharges. This will vary depending on appliances. For example, a typical
home-use coffee maker draws 500 watts during its brew time of 5 minutes.
It maintains the temperature of the pot, requiring 100 watts. Typical use of
a microwave oven is only for a few minutes. Some longer operating time
appliances are lamps, TVs, computers, and refrigerator/freezers.
Determine the total watt-hours of energy needed. This is done by multiplying
average power consumption in watts by hours of run time. For example: 500
watts for 10 hours = 5,000 watt hours. To get an estimate of the maximum
current (in amps) that a battery bank must be capable of delivering to the
inverter, divide the load watts by ten. For example a 500 watt appliance load
will need 50 amps at 12 volts DC. Using the 500 watts (or 50 amps) for 10
hours example as above, then 50 amps is needed for 10 hours. This provides us
with the basic amp-hours (AH) of battery that is required. Ten hours at 50 amps
equals 500 amp-hours (AH). There are additional factors that determine actual
run time. These include:
• AC appliance load and time in use (basic AH).
• Cable gauge and length (cable losses).
• Charge level of the batteries (between use, chargers have to be able
to fully charge the batteries).
• Temperature of the batteries (colder batteries provide fewer amps).

©2017 Wagan Corporation. All Rights Reserved.
Wagan Tech and wagan.com are trademarks of Wagan Corporation.
User’s Manual—Read before using this equipment
10
• Age and condition of the batteries (older batteries lose AH capacity).
• Compliance with turning off unnecessary AC loads.
• Use of DC appliances and compliance with turning off unnecessary
DC loads.
DERATING THE BATTERY BANK
Most lead-acid batteries have a rating expressed in amp-hours (AH). The most
common rating of AH is “at the 20 hour rate”.
NOTE: Despite several internet explanations, there is no relationship between
cold cranking amps (CCA) and ampere-hours (AH).
For example, if a 20 AH battery is discharged at a 1 amp rate, is will take 20
hours to discharge that battery. The terms “charged” and “discharged” relate to
actual battery voltage. This means that the output voltage of a nominal 12 volt
battery starts at 13.4 volts (fully charged) then drops to 10.7 volts (discharged).
If the load on the battery causes the battery to discharge faster than the 20
hour rate, the capacity (AH) of the battery is measurably reduced (derated). In
heavy battery discharge applications, double the estimated Amp Hour rating
and configure batteries to support this capacity. If the batteries are frequently
charged by an alternator, the Amp Hour rating of the battery may be reduced.
SETTING UP THE BATTERY BANK
Batteries that are used indoors or inside a vehicle or vessel, should be deep-
cycle, sealed lead acid batteries.
NOTE: It is important that for any inverter installation to battery protection fuses.
Battery fuses are added to the positive (+) battery cable as close as possible to
the battery bank’s positive terminal. The fuse amperage rating must be sized to
allow simultaneous operation of all the AC appliances to be powered, plus 20
percent safety factor. Fuses are very important to protect equipment, batteries,
and personnel. The fuses protect against battery explosion if the cables that
connect to the inverter accidentally short.

Elite™ 1000W PRO by Wagan Tech®
11 www.wagan.com
BATTERY BANK DIAGRAM
The diagram below shows inverter connections to a battery bank with
recommended fuse protection.
12V Battery Bank
Fuse
sWARNING—EXPLODING BATTERIES!!
Exploding batteries can spray molten lead, hot sulfuric acid, and other
metal, and plastic fragments. Batteries that are charging or under high
discharge rates produce explosive hydrogen gas into the surrounding
area. Be safe–fuse the battery bank and make sure the batteries are
properly ventilated.

©2017 Wagan Corporation. All Rights Reserved.
Wagan Tech and wagan.com are trademarks of Wagan Corporation.
User’s Manual—Read before using this equipment
12
DC CABLE GAUGE
Minimize cable losses by using the thickest wire available and the shortest
practical length.
Measure Round Trip (RT) cable distances in feet. Round Trip cable distance is
battery to inverter and back to battery. If the application is in a vehicle with
engine operating, use the supplied cables for round trip distances up to 5 feet.
Use a recommended ANL fuse and Fuse holder. Fuse at 125 to 150 Amps. ANL
are quick acting and sealed so they do not spark when they blow. Place fuse no
more than one foot from the Positive (+) terminal of the battery.
RT Length Up to 2 ft 3–4 ft 5–6 ft 7–9 ft 14–16 ft
AWG 64200
CONNECTING THE INVERTER
Loose connections will result in a severe voltage drop that can cause damage to
connectors, conductors, and insulation and can cause sparking. Reverse polarity
connection will blow the fuses in the inverter and can permanently damage to the
inverter. Damage caused by reverse polarity will void the warranty.
Installation procedure:
1. Mount the inverter in a secure location. If the inverter is to be mounted on a
wall, mount it horizontally. Make sure that the front and rear of the inverter
has free air flow.
2. Make sure the cables are the proper gauge and have the fuse holder as
close to the battery bank’s Positive (red) terminal.
3. Install the fuse in the Positive (red) cable.

Elite™ 1000W PRO by Wagan Tech®
13 www.wagan.com
4. Make sure the Power Switch located on the front panel of the inverter is in
the Off "O" position.
5. Locate the ground lug terminal on the inverter. Connect an insulated 10
gauge copper wire to the terminal. The other end of the ground wire is
connected to a “proper” grounding point. Use the shortest practical length
of wire. Connect this wire to the chassis of your vehicle or to the grounding
system in your boat. In a city, the ground wire can connect to a metal cold
water pipe that goes underground. In remote locations, the ground wire
can be connected to an “earth ground”. This can be an attachment to a foot
long copper clad metal rod driven into the ground. In the unlikely event of
a short circuit, operating the inverter without proper grounding can result in
electrical shock. Do not directly connect this ground wire to the Negative
(black) DC Terminal of the inverter. As an alternative grounding connection,
use the Negative (black) terminal of the battery.
NOTE: Crimp-on ring terminals are required on all cable ends. The cable
ends need to be stripped of insulation for 1/2 inch before crimping on ring
terminals. Select a crimp terminal size to fit the gauge cable and inverter
and battery terminal connectors. After crimping make sure that the cable
connectors are secure on the cables so there are no loose connections.
6. Connect the Negative (black) cable end to the inverter terminal and battery
Negative Terminal. Make sure you have good, secure connections.
7. Recheck and make sure the DC cable fuse is installed in the fuse holder.
CAUTION: Making an initial connection between the positive cable end
and the inverter’s positive terminal may cause a spark. This is a normal and
is a result of capacitors in the inverter starting to charge. Because of the
possibility of sparking, it is extremely important that both the inverter and
the battery bank be positioned away from any source of flammable fumes
or gases. Failure to heed this warning can result in fire or explosion. Do not
make the positive terminal connection immediately after the batteries have
been charging. Allow time for the battery gasses to vent to outside air.

©2017 Wagan Corporation. All Rights Reserved.
Wagan Tech and wagan.com are trademarks of Wagan Corporation.
User’s Manual—Read before using this equipment
14
8. Attach the positive cable to the Positive DC connector on the battery and
then the inverter. Make sure the connections are tight and secure.
9. Turn on the inverter from the Front Panel Power Switch "|"
10. Make certain that the green Operating LED is lit and the FAULT LED
indicator is not lit.
11. Turn Off "O" the inverter. The Fault LED may briefly “flash”. This is normal.
The audible alarm may also sound a short “chirp”. This is also normal.
12. When you have confirmed that the appliance to be operated is turned off,
plug the appliance into one of the two AC outlets on the front panel of the
inverter.
13. Turn the inverter on.
14. Check operation of the Remote Control switch. Press Lock to turn off the
inverter.
15. Press the Unlock button to turn on the inverter.
16. Turn the appliance on. The appliance should begin working.
17. Observe the LED indicators and the digital display for normal operation.
Note: If an extension cord is used from the inverter to the appliance, limit the
extension cord length to 100 feet or less. Make sure that the cord is safety
approved and AWG 14 or greater to carry the appliance load. Remember that
extension cords are for temporary use.

Elite™ 1000W PRO by Wagan Tech®
15 www.wagan.com
CHARGING THE BATTERY BANK
It is not the purpose of this inverter user’s guide to provide detailed information
regarding battery charging systems. However, the user should try to augment any
stationary inverter charging system with either wind power or solar power. These
can continue to operate during power outages and they also reduce recharge
time. For mobile or marine charging systems, a higher rated alternator may be
necessary to charge a battery bank.
REGULAR LOSS OF COMMERCIAL POWER
If the inverter system is used during commercial power outages that occur daily,
configure the charger system to replace energy during the time that commercial
power is available.
Replacement of battery energy always requires more than what was taken
from the battery (typically 30 percent more). Follow battery manufacturer’s
recommendations for maximum charging current.
sWARNING: THERE IS DANGER OF EXPLOSION. DO NOT CONNECT OR
DISCONNECT CHARGER CABLES DIRECTLY AFTER BATTERY DISCHARGE OR
RECHARGE—MAKE SURE THAT THE BATTERY BANK AREA IS WELL VENTED
BEFORE ATTACHING OR REMOVING CABLES.
If the flooded lead acid batteries are used, be sure that periodic checks of
battery electrolyte levels are accomplished. Follow battery manufacturer’s
instructions in keeping the electrolytes at the proper level. Be sure to use pure
distilled water when replacing evaporated electrolyte liquid.

©2017 Wagan Corporation. All Rights Reserved.
Wagan Tech and wagan.com are trademarks of Wagan Corporation.
User’s Manual—Read before using this equipment
16
OPERATING ISSUES: TELEVISION AND AUDIO
EQUIPMENT SUGGESTIONS.
Although all inverters are shielded and filtered to minimize signal interference,
some interference with your television picture may be unavoidable, especially
with weak signals. However, here are some suggestions that may improve
reception.
• Make sure that the television antenna produces a clear signal under normal
operating conditions (i.e. plugged into a standard 110V/120V AC wall
outlet). Also ensure that the antenna cable is of good quality and properly
shielded.
• Sometimes vehicle alternators produce some electrical noise. There are
filters available to mount on the alternator to reduce the noise.
• Change the positions of the inverter, antenna cables, and television power
cord.
• Isolate the television, its power cord, and antenna cables from the 12
volt power source by running an extension cord from the inverter to the
television.

Elite™ 1000W PRO by Wagan Tech®
17 www.wagan.com
TROUBLESHOOTING
PROBLEM: Low or No Output Voltage – Fault LED Lit
Reason Solution
Poor contact with battery, inverter
terminals.Clean terminals thoroughly. Reinstall and tighten.
PROBLEM: Inverter Auto Shut Down – Fault LED Lit
Reason Solution
Battery voltage is below 9.5 volts. Charge or replace battery.
Inverter is too hot (thermal shut down
mode). • Allow inverter to cool.
• Check for adequate ventilation.
• Reduce the load on the inverter to
the specified TrueRated™power
max output.
PROBLEM: Inverter Shut Down – Fault LED Lit
Reason Solution
Equipment being operated draws too
much power. Do not use the equipment with this inverter; use a higher wattage inverter.
PROBLEM: Continuous Buzzing Sound
Reason Solution
Input voltage is below 10.5 volts. Keep input voltage above 10.5 volts.
Poor or weak battery condition. Recharge or replace battery.
Poor or loose cable connection. Inspect terminals and tighten all
connections.
Inadequate power being delivered to
the inverter or excessive voltage drop. Use heavier gauge DC cables.
Keep cable length as short as possible.

The WAGAN Corporation warranty is limited to products sold only in
the United States.
Warranty Duration:
Product is warranted to the original purchaser for a period of two (2) years from
the original purchase date, to be free of defects in material and workmanship.
WAGAN Corporation disclaims any liability for consequential damages. In no event
will WAGAN Corporation be responsible for any amount of damages beyond the
amount paid for the product at retail.
Warranty Performance:
During the warranty period, a product with a defect will be replaced with a
comparable model when the product is returned to WAGAN Corporation with an
original store receipt. WAGAN Corporation will, at its discretion, replace or repair
the defective part. The replacement product will be warranted for the balance of the
original warranty period. This warranty does not extend to any units which have
been used in violation of written instructions furnished.
Warranty Disclaimers:
This warranty is in lieu of all warranties expressed or implied and no representative
or person is authorized to assume any other liability in connection with the sale of our
products. There shall be no claims for defects or failure of performance or product
failure under any theory of tort, contract or commercial law including,but not limited
to negligence, gross negligence, strict liability, breach of warranty, and breach of
contract.
Returns:
WAGAN Corporation is not responsible for any item(s) returned without an official
Return Authorization number (RA#). Please contact our customer service team by
phone or email to obtain an RA#. You can also visit our website and chat with our team
during our normal business hours. For more details and instructions on how to process
a warranty claim, please read the “Returns” section under the “Contact” page on our
website. WAGAN Corporation is not responsible for any shipping charges incurred in
returning the item(s) back to the company for repair or replacement.
Register your product online at http://tinyurl.com/wagan-registration to be added to
our email list. You will receive previews on our upcoming products, promotions, and
events.
©2015
WAGAN Corp. Limited Warranty

Elite™ 1000W PRO de Wagan Tech®
19 www.wagan.com
INTRODUCCIÓN
Gracias por adquirir el inversor de onda sinusoidal pura de CC a CA
Elite™ 1000W PRO de Wagan Tech®. Lea y comprenda este manual antes de
instalar y utilizar este inversor. Guarde este manual para futuras consultas.
El modelo "PRO" representa numerosas mejoras a nuestra primera generación
de Elite inversores sinusoidales puras estándar que satisfacen las necesidades
de los entornos más exigentes, suministrando energía limpia de calidad a un
precio asequible. Ofrece una verdadera CA de onda sinusoidal idéntica a la
de la energía comercial. Utilice este inversor para accionar aparatos de CA en
su vehículo. CA de onda sinusoidal pura significa que sus equipos electrónicos
sensibles, tales como sistemas de audio y video, computadoras y equipos de
comunicaciones funcionarán de forma correcta. Además, los aparatos con
motores funcionan más frescos, más silenciosos y de forma más eficiente cuando
son accionados por CA de onda sinusoidal.
El inversor se alimenta con 12 voltios de corriente continua y proporcionará
de forma continua 200 vatios de corriente alterna a 120 voltios, 60 Hz. La
capacidad superior para resistir sobretensiones de 2,000 vatios permite
que inversor encienda los aparatos motorizados más difíciles. Los circuitos
avanzados controlados por microprocesador funcionan más frescos y son más
confiables que las unidades de la competencia. El Elite™ 1000W PRO también
funciona con una alta eficiencia (hasta del 90%), que se traduce en tiempo de
funcionamiento prolongado y duración extendida de la batería en comparación
con otros inversores con este nivel de potencia de salida. Un puerto de
alimentación USB de 2.1A proporciona una manera conveniente para accionar
aparatos USB o cargar tabletas, lectores electrónicos, teléfonos inteligentes, así
como otros dispositivos electrónicos móviles.
El Elite™ 1000W PRO viene con un terminal de conexión a tierra separado
que se encuentra normalmente en unidades de mayor capacidad. Este terminal
ayuda a reducir el ruido causado por la conversión de energía al utilizar
dispositivos de radiofrecuencia.
Para su comodidad, este inversor se suministra con un mando a distancia. El
instalador debe instalar fusibles y portafusibles para protección de la batería.
Consulte "Configuración del Banco de Baterías".