Wago I/o-system 750 User manual

Pos: 2 /Dokumentation al lgemein/Einband/Ei nband Handbuch - Deckblatt ohn e Variantenfeld ( Standard) @ 9\mod_1285229289866 _0.docx @ 64941 @ @ 1

Manual

WAGO-I/O-SYSTEM 750

SSI Transmitter Interface

750-630(/xxx-xxx)

Version 1.2.0, valid from FW/HW-Version 3A/05

Pos: 3 /Alle Serien (Allge meine Module)/Hinwei se zur Dokumentation/I mpressum für Standardha ndbücher - allg. Angaben, Ansc hriften, Telefonnummern und E-Mai l-Adr essen @ 3\mod_1219151118203_ 21.docx @ 21060 @ @ 1

2 WAGO-I/O-SYSTEM 750

750-630 SSI Transmitter Interface

Manual

Version 1.2.0, valid from FW/HW-Version 3A/05

WAGO Kontakttechnik GmbH & Co. KG

Hansastraße 27

D-32423 Minden

Phone: +49 (0) 571/8 87 – 0

Fax: +49 (0) 571/8 87 – 1 69

E-Mail: [email protected]

Web: http://www.wago.com

Technical Support

Phone: +49 (0) 571/8 87 – 5 55

Fax: +49 (0) 571/8 87 – 85 55

E-Mail: [email protected]

Every conceivable measure has been taken to ensure the accuracy and

completeness of this documentation. However, as errors can never be fully

excluded, we always appreciate any information or suggestions for improving the

documentation.

E-Mail: [email protected]

We wish to point out that the software and hardware terms as well as the

trademarks of companies used and/or mentioned in the present manual are

generally protected by trademark or patent.

=== Ende der Liste für Te xtmarke Einband_vorne ===

WAGO-I/O-SYSTEM 750 Table of Contents 3

750-630 SSI Transmitter Interface

Manual

Version 1.2.0, valid from FW/HW-Version 3A/05

Pos: 5 /Dokumentation al lgemein/Verzeic hnisse/Inhaltsverzei chnis - Überschrift oG un d Verzeichni s @ 3\mod_12191512 30875_21.docx @ 21063 @ @ 1

Table of Contents

1Notes about this Documentation................................................................. 5

1.1 Validity of this Documentation................................................................. 5

1.2 Copyright................................................................................................... 6

1.3 Symbols..................................................................................................... 7

1.4 Number Notation....................................................................................... 9

1.5 Font Conventions ...................................................................................... 9

2Important Notes ......................................................................................... 10

2.1 Legal Bases ............................................................................................. 10

2.1.1 Subject to Changes ............................................................................. 10

2.1.2 Personnel Qualifications..................................................................... 10

2.1.3 Use of the WAGO-I/O-SYSTEM 750 in Compliance with Underlying

Provisions ........................................................................................... 10

2.1.4 Technical Condition of Specified Devices......................................... 11

2.2 Safety Advice (Precautions).................................................................... 12

3Device Description ..................................................................................... 14

3.1 View ........................................................................................................ 15

3.2 Connectors............................................................................................... 16

3.2.1 Data Contacts/Internal Bus................................................................. 16

3.2.2 Power Jumper Contacts/Field Supply ................................................ 17

3.2.3 CAGE CLAMP®Connectors ............................................................. 19

3.3 Display Elements .................................................................................... 20

3.4 Operating Elements................................................................................. 20

3.5 Schematic Diagram ................................................................................. 21

3.6 Technical Data ........................................................................................ 22

3.6.1 Device Data ........................................................................................ 22

3.6.2 Power Supply...................................................................................... 22

3.6.3 Communication .................................................................................. 23

3.6.4 Climatic Environmental Conditions................................................... 24

3.7 Approvals ................................................................................................ 25

3.7.1 Ex Approvals...................................................................................... 25

3.8 Standards and Guidelines........................................................................ 27

4Mounting..................................................................................................... 28

4.1 Mounting Sequence................................................................................. 28

4.2 Inserting and Removing Devices ............................................................ 29

4.2.1 Inserting the I/O Module .................................................................... 29

4.2.2 Removing the I/O Module.................................................................. 30

5Connect Devices ......................................................................................... 31

5.1 Connecting a Conductor to the CAGE CLAMP®................................... 31

6Commissioning ........................................................................................... 32

6.1 Parameterization with WAGO-I/O-CHECK........................................... 32

7Process Image............................................................................................. 34

8Use in Hazardous Environments .............................................................. 36

8.1 Marking Configuration Examples........................................................... 37

4 Table of Contents WAGO-I/O-SYSTEM 750

750-630 SSI Transmitter Interface

Manual

Version 1.2.0, valid from FW/HW-Version 3A/05

8.1.1 Marking for Europe According to ATEX and IEC-Ex ...................... 37

8.1.2 Marking for America According to NEC 500.................................... 42

8.2 Installation Regulations........................................................................... 43

8.2.1 Special Conditions for Safe Use (ATEX Certificate TÜV 07 ATEX

554086 X)........................................................................................... 44

8.2.2 Special Conditions for Safe Use (ATEX Certificate TÜV 12 ATEX

106032 X)........................................................................................... 45

8.2.3 Special Conditions for Safe Use (IEC-Ex Certificate TUN 09.0001 X)46

8.2.4 Special Conditions for Safe Use (IEC-Ex Certificate IECEx TUN

12.0039 X).......................................................................................... 47

8.2.5 Special Conditions for Safe Use According to ANSI/ISA 12.12.01.. 48

List of Figures ...................................................................................................... 49

List of Tables........................................................................................................ 50

=== Ende der Liste für Te xtmarke Verzeichnis_vorne = ==

WAGO-I/O-SYSTEM 750 Notes about this Documentation 5

750-630 SSI Transmitter Interface

Manual

Version 1.2.0, valid from FW/HW-Version 3A/05

Pos: 7 /Alle Serien (Allge meine Module)/Über schriften für alle Seri en/Hinweise zur Dokume ntation/Hinweise zu di eser Dokumentation - Über schrift 1 @ 4\mod_12 37987661750_21.doc x@ 2902 9 @ 1@ 1

1 Notes about this Documentation

Pos: 8 /Alle Serien (Allge meine Module)/Hinwei se zur Dokumentation/ Hinweise/Hinwei s: Dokumentation aufbe wahren @ 4\mod_123798733981 2_21.docx @ 29026 @ @ 1

Always retain this documentation!

This documentation is part of the product. Therefore, retain the documentation

during the entire service life of the product. Pass on the documentation to any

subsequent user. In addition, ensure that any supplement to this documentation is

included, if necessary.

Pos: 9 /Alle Serien (Allge meine Module)/Übersc hriften für alle Seri en/Hinweise zur Dokument ation/Gültigkei tsbereich - Überschr ift 2 @ 12\mod_1338912448 776_21.docx @ 96469 @ 2 @ 1

1.1 Validity of this Documentation

Pos: 10 /Serie 750 (WA GO-I/O-SYSTEM)/Hinweise zur Dokumentation/ Gültigkeitsberei ch/Gültigkeitsber eich Dokumentation Bus klemme 750-xxxx, Stand ardversion und aufge listete Varianten @ 14\mod_1358 944038682_21.doc x@ 109354 @ @ 1

This documentation is only applicable to the I/O module 750-630 (SSI

Transmitter Interface) and the variants listed in the table below.

Pos: 11 /Serie 750 (WA GO-I/O-SYSTEM)/ Hinwei se zur Dokumenta tion/Gültigkeit sbereich/Vari antenlisten/Varian tenliste - 750-630 - Standardversi on und Varianten @ 14\mod_13590234 05002_21.docx @ 109863 @ @ 1

Table 1: Variants

Item Number/Variant

Designation

750-630/000-001

SSI Transmitter Interface/ 24 Bit/ 125 kHz/ Bin

750-630/000-002

SSI Transmitter Interface/ 24 Bit/ 250 kHz/ Bin

750-630/000-004

SSI Transmitter Interface/ 24 Bit/ 125 kHz/ Gray/ Status

750-630/000-005

SSI Transmitter Interface/ 15 Bit/ 125 kHz/ Gray/ Status

750-630/000-006

SSI Transmitter Interface/ 24 Bit/ 250 kHz/ Gray

750-630/000-007

SSI Transmitter Interface/ 24 Bit/ 83 kHz/ Gray/ Status

750-630/000-008

SSI Transmitter Interface/ 25 Bit/ 125 kHz/ Gray

750-630/000-009

SSI Transmitter Interface/ 13 Bit/ 250 kHz/ Bin

750-630/000-011

SSI Transmitter Interface/ 25 Bit/ 125 kHz/ Bin

750-630/000-012

SSI Transmitter Interface/ 13 Bit/ 125 kHz/ Gray

750-630/000-013

SSI Transmitter Interface/ 29 Bit/ 125 kHz/ Bin

750-630/000-030

SSI Transmitter Interface/ 24 Bit/ 125 kHz/ Gray

750-630/003-000

SSI Transmitter InterfaceVariable configuration

Pos: 12 /Alle Serien (A llgemeine Module)/Hin weise zur Dokumentation/ Hinweise/Hin weis: Gültigkeit der Angabe n für aufgelistete Var ianten @ 9\mod_128152077814 1_21.docx @ 63085 @ @ 1

Documentation Validity for Variants

Unless otherwise indicated, the information given in this documentation applies to

listed variants.

Pos: 13 /Serie 750 (WA GO-I/O-SYSTEM)/Hinweise zur Dokumentation/ Hinweise/Achtung: Hinweis zur Dokumentation Busk lemmen 750-xxxx @ 4\mod_1237986979 656_21.docx @ 29023 @ @ 1

The I/O module 750-630 shall only be installed and operated according to the

instructions in this manual and in the manual for the used fieldbus

coupler/controller.

6 Notes about this Documentation WAGO-I/O-SYSTEM 750

750-630 SSI Transmitter Interface

Manual

Version 1.2.0, valid from FW/HW-Version 3A/05

Consider power layout of the WAGO-I/O-SYSTEM 750!

In addition to these operating instructions, you will also need the manual for the

used fieldbus coupler/controller, which can be downloaded at www.wago.com.

There, you can obtain important information including information on electrical

isolation, system power and supply specifications.

Pos: 14.1 /Alle Serien (Al lgemeine Module)/Hin weise zur Dokumentatio n/Urheberschutz ausf ührlich @ 4\mod_1235565 145234_21.docx @ 27691 @ 2 @ 1

1.2 Copyright

This Manual, including all figures and illustrations, is copyright-protected. Any

further use of this Manual by third parties that violate pertinent copyright

provisions is prohibited. Reproduction, translation, electronic and phototechnical

filing/archiving (e.g., photocopying) as well as any amendments require the

written consent of WAGO Kontakttechnik GmbH & Co. KG, Minden, Germany.

Non-observance will involve the right to assert damage claims.

Pos: 14.2 /Dokumenta tion allgemein/Glied erungselemente/---Sei tenwechsel--- @ 3\mod_122110804 5078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Notes about this Documentation 7

750-630 SSI Transmitter Interface

Manual

Version 1.2.0, valid from FW/HW-Version 3A/05

Pos: 14.3 /Alle Serien (Al lgemeine Module)/Über schriften für alleSerien/ Hinweise zur Dokumentati on/Symbole - Überschr ift 2 @ 13\mod_1351068042408 _21.docx @ 105270 @ 2 @ 1

1.3 Symbols

Pos: 14.4.1 /Alle Serien ( Allgemeine Module)/ Wichtige Erläuter ungen/Sicherheits- und sons tige Hinweise/Gefa hr/Gefahr: _W arnung vor Personenschäden al lgemein_ - Erläuterung @ 13\mod_1343309 450020_21.docx @ 101029 @ @ 1

Personal Injury!

Indicates a high-risk, imminently hazardous situation which, if not avoided, will

result in death or serious injury.

Pos: 14.4.2 /Alle Serien ( Allgemeine Module)/ Wichtige Erläuterunge n/Sicherheits- und sons tige Hinweise/Gefa hr/Gefahr: _W arnung vor Personenschäden durc h elektrischen Strom_ - Erläu terung @ 13\mod_1343309694914_ 21.docx @ 101030 @ @ 1

Personal Injury Caused by Electric Current!

Indicates a high-risk, imminently hazardous situation which, if not avoided, will

result in death or serious injury.

Pos: 14.4.3 /Alle Serien ( Allgemeine Module)/ Wichtige Erläuterunge n/Sicherheits- und sons tige Hinweise/W arnung/Warnung: _W arnung vor Personenschäden al lgemein_ - Erläuterung @ 13\mod_1 343309877041_21.d ocx@ 1010 35 @ @1

Personal Injury!

Indicates a moderate-risk, potentially hazardous situation which, if not avoided,

could result in death or serious injury.

Pos: 14.4.4 /Alle Serien ( Allgemeine Module)/ Wichtige Erläuterunge n/Sicherheits- und sons tige Hinweise/Vor sicht/Vorsic ht: _Warnung vor Personensc häden allgemein_ - Erläuterun g @ 13\mod_1343310028762_ 21.docx @ 101038 @ @ 1

Personal Injury!

Indicates a low-risk, potentially hazardous situation which, if not avoided, may

result in minor or moderate injury.

Pos: 14.4.5 /Alle Serien ( Allgemeine Module)/ Wichtige Erläuterunge n/Sicherheits- und sons tige Hinweise/Ac htung/Achtung: _W arnung vor Sachschäden allge mein_ - Erläuterung @ 13\mod_134331 0134623_21.doc x@ 101041 @ @ 1

Damage to Property!

Indicates a potentially hazardous situation which, if not avoided, may result in

damage to property.

Pos: 14.4.6 /Alle Serien ( Allgemeine Module)/ Wichtige Erläuterunge n/Sicherheits- und sons tige Hinweise/Ac htung/Achtung: _W arnung vor Sachschäden durc h elektrostatische Auf ladung_ - Erläuterung @ 13\mod_13433102 27702_21.docx @ 101044 @ @ 1

Damage to Property Caused by Electrostatic Discharge (ESD)!

Indicates a potentially hazardous situation which, if not avoided, may result in

damage to property.

Pos: 14.4.7 /Alle Serien ( Allgemeine Module)/ Wichtige Erläuterunge n/Sicherhei ts- und sonstige Hinweise/ Hinweis/Hinweis: _W ichtiger Hinweis allge mein_ - Erläuterung @ 13\mod_1343310 326906_21.doc x@ 10104 7@ @ 1

Important Note!

Indicates a potential malfunction which, if not avoided, however, will not result in

damage to property.

Pos: 14.4.8 /Alle Serien ( Allgemeine Module)/ Wichtige Erläuterunge n/Sicherheits- und sons tige Hinweise/I nformation/Infor mation: _Weitere Inf ormation allgemein_ - Er läuterung @ 13\mod_1343310439814_21. docx @ 101051 @ @1

8 Notes about this Documentation WAGO-I/O-SYSTEM 750

750-630 SSI Transmitter Interface

Manual

Version 1.2.0, valid from FW/HW-Version 3A/05

Additional Information:

Refers to additional information which is not an integral part of this

documentation (e.g., the Internet).

Pos: 14.5 /Dokumenta tion allgemein/Glied erungselemente/---Sei tenwechsel--- @ 3\mod_122110804 5078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Notes about this Documentation 9

750-630 SSI Transmitter Interface

Manual

Version 1.2.0, valid from FW/HW-Version 3A/05

Pos: 14.6 /Alle Serien (Al lgemeine Module)/Hin weise zur Dokumentatio n/Zahlensysteme @ 3\mod_12 21059454015_21.doc x@ 2171 1 @ 2 @ 1

1.4 Number Notation

Table 2: Number Notation

Number Code

Example

Note

Decimal

100

Normal notation

Hexadecimal

0x64

C notation

Binary

'100'

'0110.0100'

In quotation marks, nibble separated with

dots (.)

Pos: 14.7 /Alle Serien (Al lgemeine Module)/Hin weise zur Dokumentatio n/Schriftkon ventionen @ 3\mod_12210595214 37_21.docx @ 21714 @ 2 @ 1

1.5 Font Conventions

Table 3: Font Conventions

Font Type

Indicates

italic

Names of paths and data files are marked in italic-type.

e.g.: C:\Program Files\WAGO Software

Menu items are marked in bold letters.

e.g.: Save

A greater-than sign between two names means the selection of a

menu item from a menu.

e.g.: File > New

Input

Designation of input or optional fields are marked in bold letters,

e.g.: Start of measurement range

“Value”

Input or selective values are marked in inverted commas.

e.g.: Enter the value “4 mA” under Start of measurement range.

[Button]

Pushbuttons in dialog boxes are marked with bold letters in square

brackets.

e.g.: [Input]

[Key]

Keys are marked with bold letters in square brackets.

e.g.: [F5]

Pos: 15 /Dokumentation al lgemein/Glieder ungselemente/---Seitenwec hsel--- @ 3\mod_122110804507 8_0.docx @ 21810 @ @ 1

10 Important Notes WAGO-I/O-SYSTEM 750

750-630 SSI Transmitter Interface

Manual

Version 1.2.0, valid from FW/HW-Version 3A/05

Pos: 16 /Alle Serien (A llgemeine Module)/Übersc hriften für alle Seri en/Wichtige Erläu terungen/Wichtige Er läuterungen - Überschri ft 1 @ 4\mod_1241428899156_ 21.docx @ 32170 @ 1 @ 1

2 Important Notes

Pos: 17.1 /Alle Serien (Al lgemeine Module)/W ichtige Erläuterunge n/Wichtige Erläuter ungen - Einleitung @ 3\mod_12210598 18031_21.docx @ 21717 @ @ 1

This section includes an overall summary of the most important safety

requirements and notes that are mentioned in each individual section. To protect

your health and prevent damage to devices as well, it is imperative to read and

carefully follow the safety guidelines.

Pos: 17.2 /Alle Serien (Al lgemeine Module)/Über schriften für alleSerien/ Wichtige Erläuterung en/Rechtliche Grund lagen - Überschrift 2 @3\mod_1221060626 343_21.docx @ 21726 @ 2 @ 1

2.1 Legal Bases

Pos: 17.3 /Alle Serien (Allg emeine Module)/W ichtige Erläuterungen/ Änderungsvorbeha lt- Über schrift 3 und I nhalt @ 3\mod_1221060036484_21. docx @ 21720 @ 3 @ 1

2.1.1 Subject to Changes

WAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for any

alterations or modifications that serve to increase the efficiency of technical

progress. WAGO Kontakttechnik GmbH & Co. KG owns all rights arising from

the granting of patents or from the legal protection of utility patents. Third-party

products are always mentioned without any reference to patent rights. Thus, the

existence of such rights cannot be excluded.

Pos: 17.4 /Serie 750 (W AGO-I/O-SYSTEM)/Wichtige Erläuterungen/ Personalqualif ikationPersonalqua lifikation 750-xxxx - Überschr ift 3 und Inhalt @ 3\mod_ 1224061208046_21.doc x @ 24063 @ 3@ 1

2.1.2 Personnel Qualifications

All sequences implemented on WAGO-I/O-SYSTEM 750 devices may only be

carried out by electrical specialists with sufficient knowledge in automation. The

specialists must be familiar with the current norms and guidelines for the devices

and automated environments.

All changes to the coupler or controller should always be carried out by qualified

personnel with sufficient skills in PLC programming.

Pos: 17.5 /Serie 750 (W AGO-I/O-SYSTEM)/Wichtige Erläuterungen/ Bestimmungsgemäße V erwendungBestimmu ngsgemäße Verwendung 750-xxxx - Über schrift 3 und I nhalt @ 3\mod_1224064151234_ 21.docx @ 24070 @ 3 @ 1

2.1.3 Use of the WAGO-I/O-SYSTEM 750 in Compliance with

Underlying Provisions

Fieldbus couplers, fieldbus controllers and I/O modules found in the modular

WAGO-I/O-SYSTEM 750 receive digital and analog signals from sensors and

transmit them to actuators or higher-level control systems. Using programmable

controllers, the signals can also be (pre-) processed.

The devices have been developed for use in an environment that meets the IP20

protection class criteria. Protection against finger injury and solid impurities up to

12.5 mm diameter is assured; protection against water damage is not ensured.

Unless otherwise specified, operation of the devices in wet and dusty

environments is prohibited.

Operating the WAGO-I/O-SYSTEM 750 devices in home applications without

further measures is only permitted if they meet the emission limits (emissions of

interference) according to EN 61000-6-3. You will find the relevant information

in the section “Device Description” > “Standards and Guidelines” in the manual

for the used fieldbus coupler/controller.

WAGO-I/O-SYSTEM 750 Important Notes 11

750-630 SSI Transmitter Interface

Manual

Version 1.2.0, valid from FW/HW-Version 3A/05

Appropriate housing (per 94/9/EG) is required when operating the WAGO-I/O-

SYSTEM 750 in hazardous environments. Please note that a prototype test

certificate must be obtained that confirms the correct installation of the system in

a housing or switch cabinet.

Pos: 17.6 /Alle Serien (Al lgemeine Module)/W ichtige Erläuterunge n/Technischer Zusta nd der Geräte - Überschri ft 3 und Inhalt @ 3\mod_1221060446 109_21.docx @ 21723 @ 3 @ 1

2.1.4 Technical Condition of Specified Devices

The devices to be supplied ex works are equipped with hardware and software

configurations, which meet the individual application requirements. WAGO

Kontakttechnik GmbH & Co. KG will be exempted from any liability in case of

changes in hardware or software as well as to non-compliant usage of devices.

Please send your request for modified and new hardware or software

configurations directly to WAGO Kontakttechnik GmbH & Co. KG.

Pos: 17.7 /Dokumenta tion allgemein/Glied erungselemente/---Sei tenwechsel--- @ 3\mod_122110804 5078_0.docx @ 21810 @ @ 1

12 Important Notes WAGO-I/O-SYSTEM 750

750-630 SSI Transmitter Interface

Manual

Version 1.2.0, valid from FW/HW-Version 3A/05

Pos: 17.8 /Alle Serien (Al lgemeine Module)/Über schriften für alleSerien/ Wichtige Erläuterung en/Sicherheitshin weise - Überschrift 2 @6\mod_1260180299 987_21.docx @ 46724 @ 2 @ 1

2.2 Safety Advice (Precautions)

Pos: 17.9 /Alle Serien (Al lgemeine Module)/W ichtige Erläuterunge n/Sicherheits- und son stige Hinweise/Einlei tung Sicherheitshi nweise Hardware @ 6\mod_1260 180170493_21.doc x@ 467 20@ @ 1

For installing and operating purposes of the relevant device to your system the

following safety precautions shall be observed:

Pos: 17.10.1 /Alle Seri en (Allgemeine Module)/ Wichtige Erläuter ungen/Sicherhei ts- undson stige Hinweise/G efahr/Gefahr: Nicht an Geräten unter Spannung arbeiten! @6\mod_126018 0365327_21.doc x@ 46727 @ @ 1

Do not work on devices while energized!

All power sources to the device shall be switched off prior to performing any

installation, repair or maintenance work.

Pos: 17.10.2 /Seri e 750 (WAGO-I/O-SYSTEM)/Wichtige Erläuter ungen/Sicherheits- und s onstige Hinweise/ Gefahr/Gefahr: Einbau 0750-xx xx nur in Gehäusen, Sc hränken oder elektrischen Be triebsräumen! @ 6\mod_126 0180556692_21.doc x@ 46731 @ @ 1

Install the device only in appropriate housings, cabinets or in electrical

operation rooms!

The WAGO-I/O-SYSTEM 750 and its components are an open system. As such,

install the system and its components exclusively in appropriate housings,

cabinets or in electrical operation rooms. Allow access to such equipment and

fixtures to authorized, qualified staff only by means of specific keys or tools.

Pos: 17.10.3 /Alle Seri en (Allgemeine Module)/ Wichtige Erläuterung en/Sicherheits- und son stige Hinweise/G efahr/Gefahr: Unfal lverhütungsvorsc hriften beachten! @ 6\mod_1 260180657000_21.doc x@ 4673 5 @ @ 1

Pos: 17.10.4 /Alle Seri en (Allgemeine Module)/ Wichtige Erläuter ungen/Sicherhei ts- undson stige Hinweise/G efahr/Gefahr: Auf nor mgerechten Anschluss ac hten! @ 6\mod_1260180753479 _21.docx @ 46739 @ @ 1

Pos: 17.11.1 /Alle Seri en (Allgemeine Module)/ Wichtige Erläuterung en/Sicherheits- und son stige Hinweise/Ac htung/Achtung: Defek te oder beschädigte Gerä te austauschen! @ 6\mod_126 0180857358_21.doc x@ 46743 @ @ 1

Replace defective or damaged devices!

Replace defective or damaged device/module (e.g., in the event of deformed

contacts), since the long-term functionality of device/module involved can no

longer be ensured.

Pos: 17.11.2 /Alle Seri en (Allgemeine Module)/ Wichtige Erläuterung en/Sicherhei ts- und sonstige Hinweise/ Achtung/Achtung: Geräte vor kriechenden und isolier enden Stoffen schütze n! @ 6\mod_1260181036216_21. docx @ 46747 @ @ 1

Protect the components against materials having seeping and insulating

properties!

The components are not resistant to materials having seeping and insulating

properties such as: aerosols, silicones and triglycerides (found in some hand

creams). If you cannot exclude that such materials will appear in the component

environment, then install the components in an enclosure being resistant to the

above-mentioned materials. Clean tools and materials are imperative for handling

devices/modules.

Pos: 17.11.3 /Alle Seri en (Allgemeine Module)/ Wichtige Erläuterung en/Sicherheits- und son stige Hinweise/Ac htung/Achtung: Reini gung nur mit zulässig en Materialien! @ 6\mod_1260 181203293_21.docx @ 46751 @ @ 1

Clean only with permitted materials!

Clean soiled contacts using oil-free compressed air or with ethyl alcohol and

leather cloths.

Pos: 17.11.4 /Alle Seri en (Allgemeine Module)/ Wichtige Erläuterung en/Sicherheits- und son stige Hinweise/Ac htung/Achtung: Kein Kon taktspray verwend en! @ 6\mod_1260181290808_2 1.docx @ 46755 @ @ 1

WAGO-I/O-SYSTEM 750 Important Notes 13

750-630 SSI Transmitter Interface

Manual

Version 1.2.0, valid from FW/HW-Version 3A/05

Do not use any contact spray!

Do not use any contact spray. The spray may impair contact area functionality in

connection with contamination.

Pos: 17.11.5 /Alle Seri en (Allgemeine Module)/ Wichtige Erläuterung en/Sicherheits- und son stige Hinweise/Ac htung/Achtung: Verpo lung vermeiden! @ 6\mod_126 0184045744_21.doc x@ 46767 @ @ 1

Do not reverse the polarity of connection lines!

Avoid reverse polarity of data and power supply lines, as this may damage the

devices involved.

Pos: 17.11.6 /Alle Seri en (Allgemeine Module)/ Wichtige Erläuterung en/Sicherheits- und son stige Hinweise/Ac htung/Achtung: Elek trostatische Entlad ung vermeiden! @ 6\mod_12601 81364729_21.doc x@ 46759 @ @ 1

Avoid electrostatic discharge!

The devices are equipped with electronic components that may be destroyed by

electrostatic discharge when touched. Please observe the safety precautions

against electrostatic discharge per DIN EN 61340-5-1/-3. When handling the

devices, please ensure that environmental factors (personnel, work space and

packaging) are properly grounded.

Pos: 18 /Dokumentation al lgemein/Glieder ungselemente/---Seitenwec hsel--- @ 3\mod_122110804507 8_0.docx @ 21810 @ @ 1

14 Device Description WAGO-I/O-SYSTEM 750

750-630 SSI Transmitter Interface

Manual

Version 1.2.0, valid from FW/HW-Version 3A/05

Pos: 19 /Alle Serien (A llgemeine Module)/Über schriften für alle Seri en/Gerätebeschrei bung/Gerätebeschr eibung - Überschrif t 1 @ 3\mod_1233756084656_21.doc x @ 27096 @ 1 @ 1

3 Device Description

Pos: 20.1.1 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschrei bung/Einleitung/An wendung/SO/Anwendung 750-06 30 @ 9\mod_1290755613293_ 21.docx @ 66880 @ @ 1

The I/O module functions as an SSI interface and outputs a pulse signal to read

the sensor.

The I/O module reads the incoming data and transmits it directly in the form of a

data word in the process image.

It is possible to set different operating modes, transfer frequencies and data widths

by means of the control register (see Variant List).

Pos: 20.1.2 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschrei bung/Einleitung/I /O-Beschreibung/S O/I/O-Beschreibung 750-0630 @ 9\ mod_1290755754387_21. docx @ 66883 @ @ 1

The SSI absolute encoder can be connected to the CAGE CLAMP®terminals +D,

−D, +CL and −CL directly.

The power supply for the encoder can be tapped from the I/O module directly.

Pos: 20.1.3 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschreibung/ Einleitung/I/ O-Beschreibung/Allg emein/Verweis auf Kapitel"A nschlüsse" @ 8\mod_1276775378035_21.docx @ 57956 @ @ 1

The assignment of the connections is described in the “Connectors” section.

Pos: 20.1.4 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschreibung/ Einleitung/LED-Anzei ge/LED Zustand Betri eb Klemme @ 14\mod_13590409 91238_21.docx @ 109921 @ @ 1

The operating status of the I/O module is indicated by a green status LED.

Pos: 20.1.5 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschreibung/Ei nleitung/LED-Anzeig e/Verweis auf Kapi tel "Anzeigeele mente" @ 5\mod_1246010525 000_21.docx @ 36194 @ @ 1

The meaning of the LEDs is described in the “Display Elements” section.

Pos: 20.1.6 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschrei bung/Einleitung/Ver sorgung/Anordnun g unter Berücksic htigung der Leistungskontak te beliebig @ 3\mod_12337562 33468_21.docx @ 27099 @ @ 1

With consideration of the power jumper contacts, the individual modules can be

arranged in any combination when configuring the fieldbus node. An arrangement

in groups within the group of potentials is not necessary.

Pos: 20.1.7 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschrei bung/Einleitung/Ver sorgung/Versorgung 2 4 V, 0 V über Leistungskonta kte Standard @ 3\mod_122649 8974531_21.doc x@ 25020 @ @ 1

The I/O module 750-630 (SSI Transmitter Interface) receives the 24 V voltage

supply for the field level from an upstream I/O module or from the fieldbus

coupler/controller via blade-formed power jumper contacts. It then provides these

potentials to subsequent I/O modules via spring-formed power jumper contacts.

Pos: 20.1.8 /Seri e 750 (WAGO-I/O-SYSTEM)/Wichtige Erläuterun gen/Sicherheits- und so nstige Hinweise/ Hinweis/Hinweis: Poten tialeinspeisek lemme für Erde einsetzen! (keineLK fürE rde) @ 3\mod_1226499037468_21.doc x @ 25023 @ @1

Use supply modules for ground (earth)!

The I/O module has no power jumper contacts for receiving and transmitting the

earth potential. Use a supply module when an earth potential is needed for the

subsequent I/O modules.

Pos: 20.1.9 /Seri e 750 (WAGO-I/O-SYSTEM)/Wichtige Erläuterun gen/Sicherheits- und so nstige Hinweise/Ac htung/Achtung: Maxi maler Strom Leistungsk ontakte 10 A @ 3\mod_1226499143 500_21.docx @ 25029 @ @ 1

Do not exceed maximum current via power jumper contacts!

The maximum current to flow through the power jumper contacts is 10 A.

Greater currents can damage the contacts.

When configuring your system, ensure that this current is not exceeded. If

exceeded, insert an additional supply module.

Pos: 20.1.10 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschrei bung/Einleitung/ Versorgung/Gal vanische Trenn ung Feld/System @ 3\mod_1233756478750_21.doc x@ 27102 @ @ 1

The field voltage and the system voltage are electrically isolated from each other.

Pos: 20.1.11 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschrei bung/Einleitung/Ei nsatzbereich/ Einsatzbereich 750-xxxx al le Koppler/Controller ohneEcono my-Koppler @ 3\mod_123254186746 8_21.docx @ 26525 @ @ 1

The I/O module 750-630 can be used with all fieldbus couplers/controllers of the

WAGO-I/O-SYSTEM 750 (except for the economy types 750-320, -323, -324

and -327).

Pos: 20.1.12 /Alle Seri en (Allgemeine Module)/ Hinweise zur Dokumen tation/Gültigkei tsbereich Dokumentation E rgänzung "ab HW/SW -Version" @ 20\mod_1407749774742_ 21.docx @ 161508 @ @ 1

This documentation is only applicable from FW/HW-Version 3A/05.

Pos: 20.2 /Dokumenta tion allgemein/Glied erungselemente/ ---Seitenwechsel--- @ 3\mod_12211 08045078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 15

750-630 SSI Transmitter Interface

Manual

Version 1.2.0, valid from FW/HW-Version 3A/05

Pos: 20.3 /Alle Serien (Al lgemeine Module)/Über schriften für alleSerien/ Gerätebeschreibun g/Ansicht - Überschrif t 2 @ 4\mod_1240984217343_21. docx @ 31958 @ 2 @ 1

3.1 View

Pos: 20.4 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/ Ansicht/Sonderk lemmen/Ansicht 750-063 0 @ 10\mod_1299070729577_21. docx @ 70360 @ @1

Figure 1: View

Pos: 20.5 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/ Ansicht/Ansic ht CageClamp®_Legende mitLEDs @ 15\mo d_1370867188922_21.doc x @ 122225 @ @1

Table 4: Legend for Figure “View”

Pos.

Description

Details See Section

Marking possibility with Mini-

WSB

---

Status LEDs

“Device Description” > “Display Elements”

Data contacts

“Device Description” > “Connectors”

CAGE CLAMP®connectors

“Device Description” > “Connectors”

Power jumper contacts

“Device Description” > “Connectors”

Release tab

“Mounting” > “Inserting and Removing

Devices”

Pos: 20.6 /Dokumenta tion allgemein/Glied erungselemente/---Sei tenwechsel--- @ 3\mod_122110804 5078_0.docx @ 21810 @ @ 1

16 Device Description WAGO-I/O-SYSTEM 750

750-630 SSI Transmitter Interface

Manual

Version 1.2.0, valid from FW/HW-Version 3A/05

Pos: 20.7 /Alle Serien (Al lgemeine Module)/Über schriften für alleSerien/ Gerätebeschreibun g/Anschlüsse - Überschr ift 2 @ 4\mod_12409842626 56_21.docx @ 31961 @ 2 @ 1

3.2 Connectors

Pos: 20.8 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/ Anschlüsse/Datenk ontakte/Klemmenbus - Übersc hrift 3 @ 6\mod_1256294684 083_21.docx @ 43660 @ 3 @ 1

3.2.1 Data Contacts/Internal Bus

Pos: 20.9.1 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschrei bung/Anschlüsse/Datenko ntakte - Feldbuskoppler /-controller, Abbi ldung und Beschreibung @ 3\mod _1231771259187_21.doc x @ 26002 @ @ 1

Communication between the fieldbus coupler/controller and the I/O modules as

well as the system supply of the I/O modules is carried out via the internal bus. It

is comprised of 6 data contacts, which are available as self-cleaning gold spring

contacts.

Figure 2: Data Contacts

Pos: 20.9.2 /Seri e 750 (WAGO-I/O-SYSTEM)/Wichtige Erläuterun gen/Sicherheits- und sons tige Hinweise/Achtung/Ac htung: Busklemmen nicht auf Goldfederko ntakte legen! @ 7\mod_1266318463636_21. docx @ 50695 @ @1

Do not place the I/O modules on the gold spring contacts!

Do not place the I/O modules on the gold spring contacts in order to avoid soiling

or scratching!

Pos: 20.9.3 /Seri e 750 (WAGO-I/O-SYSTEM)/Wichtige Erläuterun gen/Sicherheits- und so nstige Hinweise/Ac htung/Achtung: ESD - Auf guteErdung der Umgebung achten! @ 7\mod_1266318538 667_21.docx @ 50708 @ @ 1

Ensure that the environment is well grounded!

The devices are equipped with electronic components that may be destroyed by

electrostatic discharge. When handling the devices, ensure that the environment

(persons, workplace and packing) is well grounded. Avoid touching conductive

components, e.g. data contacts.

Pos: 20.10 /Dokumenta tion allgemein/Glie derungselemente/---Sei tenwechsel--- @ 3\mod_1221108045078_0. docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 17

750-630 SSI Transmitter Interface

Manual

Version 1.2.0, valid from FW/HW-Version 3A/05

Pos: 20.11 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/ Anschlüsse/Leistu ngskontakte/Feld versorgung - Überschrift 3 @6\mod_125629469286 4_21.docx @ 43664 @ 3 @ 1

3.2.2 Power Jumper Contacts/Field Supply

Pos: 20.12.1 /Seri e 750 (WAGO-I/O-SYSTEM)/Wichtige Erläuter ungen/Sicherheits- und s onstige Hinweise/Vorsi cht/Vorsicht: Verletzungsgefahr durc h scharfkantige Messer kontakte! @ 6\mod_1256193279 401_21.docx @ 43414 @ @ 1

Risk of injury due to sharp-edged blade contacts!

The blade contacts are sharp-edged. Handle the I/O module carefully to prevent

injury.

Pos: 20.12.2 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschrei bung/Anschlüsse/Lei stungskontakte 2 LK ( Messer/Leistungsko ntakte 2 LK (Messer/Feder ) - Einleitung @ 15\mod_13717216410 99_21.docx @ 123714 @ @ 1

The I/O module 750-630 has 2 self-cleaning power jumper contacts that supply

and transmit power for the field side. The contacts on the left side of the I/O

module are designed as blade contacts and those on the right side as spring

contacts.

Pos: 20.12.3 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschrei bung/Anschlüsse/Leis tungskontakte 2 LK (Me sser/Leistungsko ntakte 2 LK (Messer/Feder ) - Abbildung, einfache Br eite - Standard @ 15\mod_136750070003 7_21.docx @ 118396 @ @ 1

Figure 3: Power Jumper Contacts

Pos: 20.12.4 /Seri e 750 (WAGO-I/O-SYSTEM)/Gerätebeschrei bung/Anschlüsse/Leis tungskontakte 2 LK (Me sser/Leistungskonta kte 2 LK (Messer/Feder) -Legende @ 15\m od_1371721352500_21.d ocx @ 123710 @ @1

Table 5: Legend for Figure “Power Jumper Contacts”

Contact

Type

Function

Spring contact

Potential transmission (Uv) for field supply

Spring contact

Potential transmission (0 V) for field supply

Blade contact

Potential feed-in (0 V) for field supply

Blade contact

Potential feed-in (Uv) for field supply

Pos: 20.12.5 /Seri e 750 (WAGO-I/O-SYSTEM)/Wichtige Erläuter ungen/Sicherheits- und s onstige Hinweise/Ac htung/Achtung: Maxi maler Strom Leistungs kontakte 10 A @ 3\mod_122649914 3500_21.docx @ 25029@ @ 1

Do not exceed maximum current via power jumper contacts!

The maximum current to flow through the power jumper contacts is 10 A.

Greater currents can damage the contacts.

When configuring your system, ensure that this current is not exceeded. If

exceeded, insert an additional supply module.

Pos: 20.12.6 /Seri e 750 (WAGO-I/O-SYSTEM)/Wichtige Erläuter ungen/Sicherheits- und s onstige Hinweise/ Hinweis/Hinweis: Po tentialeinspeisek lemme für Erde einsetzen! ( keine LK für Erde) @ 3\mod_12264 99037468_21.docx @ 25023 @ @ 1

18 Device Description WAGO-I/O-SYSTEM 750

750-630 SSI Transmitter Interface

Manual

Version 1.2.0, valid from FW/HW-Version 3A/05

Use supply modules for ground (earth)!

The I/O module has no power jumper contacts for receiving and transmitting the

earth potential. Use a supply module when an earth potential is needed for the

subsequent I/O modules.

Pos: 20.13 /Dokumenta tion allgemein/Glie derungselemente/---Sei tenwechsel--- @ 3\mod_1221108045078_0. docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 19

750-630 SSI Transmitter Interface

Manual

Version 1.2.0, valid from FW/HW-Version 3A/05

Pos: 20.14 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/ Anschlüsse/CAGE CLA MP-Anschlüsse - Überschrif t 3 @ 6\mod_1256296337770_21. docx @ 43674 @ 3 @ 1

3.2.3 CAGE CLAMP®Connectors

Pos: 20.15 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/ Anschlüsse/Sonder klemmen/Anschlüs seC C 750-0630 @ 10\mod_129907098592 2_21.docx @ 70364 @ @ 1

Figure 4: CAGE CLAMP®Connectors

Table 6: Legend for Figure “CAGE CLAMP®Connectors“

Designation

Connector

Function

Data in

24 V

Field supply 24 VDC

0 V

Field supply 0 VDC

+CLK

CLOCK output

−D

Data in

24 V

Field supply 24 VDC

0 V

Field supply 0 VDC

−CLK

CLOCK output

Pos: 20.16 /Dokumenta tion allgemein/Glie derungselemente/---Sei tenwechsel--- @ 3\mod_1221108045078_0. docx @ 21810 @ @ 1

20 Device Description WAGO-I/O-SYSTEM 750

750-630 SSI Transmitter Interface

Manual

Version 1.2.0, valid from FW/HW-Version 3A/05

Pos: 20.17 /Alle Serien ( Allgemeine Module)/ Überschriften für alleSerien/ Gerätebeschrei bung/Anzeigeelemente - Über schrift 2 @ 4\mod_124098439 0875_21.docx @ 31964 @ 2 @ 1

3.3 Display Elements

Pos: 20.18 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/ Anzeigeelemente/ Sonderklemmen/Anzei geelemente 750-0630 @ 10\mod_12 99071069932_21.doc x@ 70368 @ @ 1

Figure 5: Display Elements

Table :7 Key for the “Display Elements” Figure

Designation LED State Function

Status A

Off

Watchdog Timer Overflow 1)

Green

Normal mode

1) If the fieldbus coupler/controller does not transmit any process data for 100 ms,

the LED goes out.

Pos: 20.19 /Alle Serien ( Allgemeine Module)/ Überschriften für alleSerien/ Gerätebeschrei bung/Bedienelemente - Übersc hrift 2 @ 4\mod_123919 1655456_21.docx @ 30439 @ 2 @ 1

3.4 Operating Elements

Pos: 20.20 /Serie 750 (W AGO-I/O-SYSTEM)/Gerätebeschreibung/ Bedienelemente/Be dienelemente Buskle mme 750-xxxx nicht vorhande n @ 4\mod_1236322031125_21. docx @ 28063 @ @1

The I/O module 750-630 has no operating elements.

Pos: 20.21 /Alle Serien ( Allgemeine Module)/ Überschriften für alleSerien/ Gerätebeschrei bung/Schematisches Scha ltbild - Überschrif t 2 @ 4\mod_12409844 41312_21.docx @ 31967 @ 2 @ 1