Wali M00LP User manual

2. Remove the screw, washer and top plate from the M10 Hand Knob m , then connect the M10 Hand
Knob m and C-clamp b with the screw, washer and top plate that were just removed.
Select the preferred height according to your desk thickness. Connect C-clamp b to C-clamp Brace c
using M8x12 Bolt g , and tighten with Allen Key 5mm i . Rotate the Hand Knob m clockwise to fasten
for stability.
M00LP/M00LP-W
Laptop Tray Desk Mount
75x75\100x100
INSTALLATION MANUAL
1-844-SATTLER (18447288537)
[email protected]
www.walielectric.com
(10kg/22lbs)
RATED
WARNING
！
！
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIP OVER.
SMALL PARTS- NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may
cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual.
Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect
assembly or inappropriate use.
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
TIPOVER WARNING
Supplied Parts List
Laptop : 17'' Max
Monitor：27'' Max
Option A : Clamp Installation
1. Connect Pole a and C-Clamp Brace c from the bottom using M5x14 Bolt f and
tighten with Allen Key 3mm o .
Option B : Grommet Base Installation
1. Place Pole a onto Grommet Base Plate m . Connect them from the bottom using M5x14 Bolt
and tighten with Allen Key 3mm .
a
i
i
i
i
i
f
o
c
c
cc
c
af
a
a
q
q
q
n
q
f
f
1
Stick the EVA pad B to
the C-Clamp Brace c
o
3mm
Wire Clip
l (x2)
Wire Clip
k (x1)
Grommet Base Plate
q (x1)
Support Plate
p (x1)
M10 Hand Knob
m (x1)
EVA Pad A
n (x1)
EVA Pad B
o (x1)
Pole
a (x1)
VESA Plate
e (x1)
M5x14 Bolt
f (x3)
M4x12 Bolt
j (x4)
Swivel Arm
d (x1)
Anti-skid Pad
u (x4)
M4x12 Bolt
s (x4)
Laptop Tray
r (x1)
D4 Nut
t (x4)
C-Clamp
b (x1)
C-Clamp Brace
c (x1)
m
m
m
b
im
Stick the EVA pad A o to
the Grommet Base Plate
n
v (x1)
Wrench
b
g
g
b
c
M6 Nut
h (x1)
M8x12 Bolt
g (x2)
Allen Key
i (x1)
mb

6Manually swivel, tilt, and rotate the tray for the best viewing angle. 5Guide the cable through the Wire Clips ( h , i ) and store the Allen Keys o in the
Wire Clip . Adjust the tilt angle using Allen Key 5mm n .
15°
15°
l
i
i
k
k
l
i
k
4
d
e
v
h
i
2
Put the Wire Clip h and Swivel Arm c through the Pole a , adjust the preferred height and
tighten using Allen Key 6mm o . Attach the Wire Clips l to the Swivel Arm c .
d
d
d
l
l
k
k
a
a
i
i
e
j
r
w
t
u
s
e
Option A : Laptop Tray Installation
Using M4x12 Bolt u and D4 Nut v to attach the VESA Plate e to the Laptop Tray r and
tighten with a screwdriver. Put the Anti-skid Pad u on the designated position on the tray.
(Screwdriver not included)
3
Option B : Monitor Mount Installation
Laptop Tray Holder
Notice: For safety, please remove your laptop when making adjustments.
u
er
t
s
Remove the screw, washer and top plate from the M10 Hand Knob m . Mark the position of the hole on your mounting surface. Drill a 3/8"(10mm)
diameter hole at the marked position through the mounting surface.
Position the Pole a on the mounting surface and connect the hand knob mthrough the Support Plate p and the self-drilled hole with the Pole a .
Rotate the hand knob mclockwise to fasten for stability.
Remove the screw, washer and top plate from the M10 Hand Knob m . If the existing grommet hole comes with a plastic protector, remove it to
ensure a flat surface before installing the desk mount.
Position the Pole a on the mounting surface and connect the hand knob Nthrough the Support Plate p and the grommet hole with the Pole a .
Rotate the hand knob Nclockwise to fasten for stability.
a
a
aa
a
m
m
p
m
m
m
m
m
2a. Existing Grommet Hole Installation 2b. Self-drilled Grommet Hole Installation
pp
ø 10mm
(ø ")3/8
m
a
m
p
m
Notice: Please make sure the security nut
is installed before you rotate the monitor/laptop.
Put the assembled laptop tray onto the Swivel Arm d and install the security M6 Nut h as the
image shown. Tighten the M6 Nut h
using the Wrench for stability.
h
h
v
d