W&F-LOCKS 1402 "One-Timer" Manual

Technical Information
Locking System 1402 "One-Timer"
1.
1.1
1.2
2.
2.1
2.2
2.3
2.4
3.
3.1
3.2
3.3
4.
4.1
4.2
5.
5.1
5.2
5.3
Revision: 23.10.2018 / Technical changes reserved / All data without warranty / (c) W&F-LOCKS OHG 2017
Product Description
Main Features
General Information
Assembly Instructions
Important Hints for Fitters
Assembly Exploded View
Fitting Dimensions and Tightening Torques
Setting direction of rotation
Operating Instructions for users
Inportant Hints for Users
Personal code setting and locking
Open the lock
Operation Instructions for Administrators
Important Hints for Administrators
QUICK-RESET / Emergency Opening
Ordering Information
Important Basic Information
Ordering Matrix Cam
Ordering Matrix Lock / Service Key
2
2
2
3
3
3
4
5
6
6
6
6
7
7
7
8
8
9
10
.................................................................................
......................................................................................
...............................................................................
............................................................................
......................................................................
....................................................................
..............................................
........................................................................
..............................................................
.......................................................................
.............................................................
............................... ..........................................................
.................................................
............................................................
........................................................
..............................................................................
....................................................................
.................................................................................
..............................................................

1.2 General Information
- Please read carefully these instructions before fitting and first use
- Do not expose lock to enviromental influences like water, moist, dust etc.
- Lock operable within a temperature range from 0- 50°C (32°F to 120°F)
- For cleaning use damp cloth and common houshold detergent
- Don't use aggressive or chemical products
- When cleaning avoid that water or detergend enters the lock
- 2 -
1.1 Main Features
- Combination lock with 10.000 freely programmable user-codes
- Service cylinder with 200 different key numbers for emergency opening and resetting
- QUICK-RESET
1
for an efficient administration
- ANTI-SPY
2
-technology to protect the personal user-codes
- Automatic code-scrambling for even more safety and comfort
- Lock movement R / L settable
- Locking mechanism made of solid zinc die-cast
- Housing made of fibreglass-reinforced and easy to clean special plastic
- Retrofittable for most doors with standard fixing holes 16x19mm
- Lock fixing by nut (SW22)
- Cam fixing by screw (TX25)
- Comprehensive range of cams available with 2 and 3mm thickness
- Ideally suited for 1-point and 3-point cams
1
Innovative function to restore to factory setting within seconds without time-consuming
codefinding
2
Innovative lock-system wherewith the readout and misuse of personal user-codes is no
longer possible
For more informationen visit: wf-locks.com
1. Product Description 1402 "One-Timer"

Cam fixing screw (TX25)
Lock fixing nut (WDF22)
Locking system
1402
Panel
with 16x19mm piercing hole
Cam
2.2 Assembly Exploded-View
Guide-washer
2.1 Important Hints for Fitters
- Use only the supplied original fixing elements
- The cam fixing screw is thread-forming and self-retaining
- Use only suitable and properly functioning tools
- Do not break the torque limits
- Lock movement must be set by the guide-washer before fixing the cam (see 2.4)
- The lock movement is 90°
- The 16x19 piercing hole must be vertical
- In locked position the code-wheels are horizontal aligned
- Adhere the required tolerances of the piercing hole
- 3 -
Ring-washer
2. Assembly Instructions 1402 "One-Timer"

30
20,5
60
Lock fixing nut (WAF22)
M: max. 8Nm
Recommended
distance
from centre of piercing
to edge of door
(for new piercing holes)
Cam fixing screw (TX25)
M: max. 6Nm
15,5
min. 5
If locking into a slot
allow clearance
19
+0,2 0
16
+0,2
0
32
Piercing hole
2. Assembly Instructions 1402 "One-Timer"
- 4 -
Panel
thickness
max.
12mm
2.3 Fitting Dimensions and Tightening Torques

90°
90°
2.4 Setting direction of rotation
"R" for right-hinged doors
2. Assembly Instructions 1402 "One-Timer"
Orientation guide washer
in locked-position
Direction of rotation to unlock
"L" for left-hinged doors
- 5 -
90°
R
90°
L

3.2 Personal code setting and locking
3.3 Open the lock
1. In vertical position
set personal code
2. Turn lock to the horizontal position
until it clicks into place
(Code is stored and scrambled)
1
2
2
1
- 6 -
1. Enter personal Code
2. Turn lock to the vertical position
(Code is deleted)
3. Operation Instructions for Users
1402 "One-Timer"
3.1 Important hints for users
- In opened position with vertically aligned numbers the lock is in coding mode
- In vertical position displayed or selected code is automatically stored and scrambled
when closing.
- Before closing, remember the code fixed by you or note it down if needed
- Do not select 0-0-0-0 as personal code
- With every opening your personal code is automatically deleted
- In case of lost code contact the administrator
- Leave you locker with opened lock in vertical position

4. Operation Instructions for Administrators
1402 "One-Timer"
4.1 Important hints for Administrators
- With service key you can always open the lock
- With every openeing the code is deleted
- Service key can only be removed in closed position
- Service key is provided with key numbers
- For security reasons please keep the number of service keys at a minimum and keep it
in a safe place
4.2 QUICK-RESET
Insert service key into barrel
and turn it 90° to the left
1.
1
2
2. Open the lock
- 7 -

5.1 Important Basic Information
Lock, cam and service key will be ordered seperately. A complete order or inquiry
comprises 3 order numbers:
1. Order no. cam
2. Order no. lock
3. Order no. service key
Cam and fixing elements are standardly delivered unmounted. On request the cam
can be premounted as well. The needed specification for that will be done according to
order matrix 5.2.
Important: If you want the cam premounted please make sure that the lock with fixed
cam still fits through the 16x19 pircing hole. That mainly depents on the cam shape and the
panel thickness.
The factory-set code is 0-0-0-0.
For security reasons please keep the number of service keys at a minimum.
Service keys and locks are provided with key numbers. For security reasons the key
number of the lock is on the back.
Each order quantity will be delivered keyed to pass. This means that all locks have the
same key number (differ number), with one key opening all.
If you need different key numbers e.g. in order to equip different rooms or permissions
please split the order quantity in different key numbers.
For the service cylinder please chose one of the standard key numbers according the order
matrix 5.3. On request there are additional 200 key numbers available.
For short delivery times please prefer the given standards from the order matrices.
But special designs such as differnt colours or something else can also be requested
at any time.
Beispiel: C1402-3-4-20-30-DO
Beispiel: L1402-G-051-R-09-H
Beispiel: S1402-051
(Bestellmatrix 5.2)
(Bestellmatrix 5.3)
(Bestellmatrix 5.3)
- 8 -
5. Ordering Information 1402 "One-Timer"

5.2 Ordering Matrix Cam
3. Hight of crank "A"
2. Shape
C1402- 3 - 4 - 20 - 38 - DO
5. Cam end
1. Thickness "T"
5. Ordering Information 1402 "One-Timer"
4. Lenght "B"
Order example cam :
12
34
5
6
7
8
9
A
0,3
A
0,3
A
mm
für Form
20,5
00
03
04
05
06
07
08
10
12
14
16
20
21
25
28
32
34
38
40
44
48
50
64
72
0
1,2
1,6
2,0
2,4
2,8
3,2
4,0
4,8
5,6
6,4
7,9
8,3
9,9
11,1
12,7
13,5
15,0
15,9
17,5
19,1
19,9
25,4
28,6
-1-2-
-3-5-6-
-3-5-6-
-3-5-6-
-3-5-6-
-3-5-6-
-3-5-6-
-3-5-6-
-3-4-5-6-7-8-
-3-4-5-6-7-8-
-4-7-8-9-
-4-7-8-9-
-3-5-6-
-3-4-5-6-7-8-9-
-4-7-8-9-
-3-4-5-6-7-8-9-
-4-7-8-9-
-4-7-8-9-
-4-7-8-9-
-4-7-8-9-
-4-7-8-9-
-4-7-8-9-
-4-7-8-9-
-4-7-8-9-
15,5 T
T = 2mm / 3mm
-Lenght "B" made to order
-Step range 1mm
-Lenght before bending max.100mm
DO (Standard)
DX
DB
B0,5
10
5,5
7,5 0,25
12,5 0,3
9
R
9
R
- 9 -
B
A
A
T
38
7,9
3

1. Colour
2. Service cylinder key no.
3. Direction of rotation
4. Cam position
5. Crank direction
033
041
051
Only needed if premounting of cam requested (see hint uneder 5.1)
Always needed Information
G
B
(black)
(dusty grey
RAL 7073)
L
R
12
03
06
09
H
V
Order example lock:
(grey lock with premounted cam)
(for cam order see 5.2)
Order example service key:
(matching the lock above)
View from front when locked
R: right hinged doors
L: left hinged doors
(Special key numbers on request)
(Special colours on request)
L1402- G - 051 - R - 09 - H
S1402- 051
- 10 -
(if cranked)
5. Ordering Information 1402 "One-Timer"
5.3 Ordering Matrix Lock / Service Key