WAREMA WG.F.08 Specification sheet

WAREMA ceiling roller blind
type WG.F.08
Instructions for use and maintenance
To be handed over to the operator
Valid from 25 September 2009
Document number [B867423_0] – EN

Introduction
[B867213_0] - EN/ 25.09.09 Page 2 of 12 Subject to change without notice.
1Introduction
1.1 Information on safety
It is important to follow these instructions in the interests
of personal safety. Failure to comply with these
instructions when operating the product may result in
personal injury and/or property damage. Failure to comply
with these instructions relieves WAREMA of liability.
Warnings are marked with these symbols in
the instructions.
Read through the instructions carefully
before use.
Keep the instructions until you dispose of
the product.
Include these instructions if you pass the
product on to a new owner.
Please observe all safety, operating, and
maintenance instructions.
1.2 Information on the target group and
application of these instructions
Target group
These instructions are intended for use by a trained
operator.
Contents
These operating and maintenance instructions contain
important information on operation and maintenance. It
describes the operation of the WAREMA ceiling roller
blind with 230-volt electric drive. Other drives and
alternative solutions are not dealt with.
Permissible activities
No other alterations, additions to or conversions of, or
maintenance work, are to be carried out on the product
other than as described in these instructions without the
written approval of WAREMA.
1.3 Explanation of symbols and signs
Safety information and symbols are contained in the
appropriate parts of the text.
Symbol Use/explanation
DANGER
Identifies an imminent danger that may result
in death or serious injury if not prevented.
WARNING
Identifies a potential danger that may result in
death or serious injury if not prevented.
CAUTION
Identifies a potential danger that may result in
minor injury or property damage if not
prevented.
Read the instructions for use and mainte-
nance.
 Note
Important information on how to proceed and
on the content of these instructions.


Activity/step

Table of contents
[B867213_0] - EN/ 25.09.09 Page 3 of 12 Subject to change without notice.
Table of contents
1Introduction ....................................................................................................................... 2
1.1Information on safety....................................................................................................................................... 2
1.2Information on the target group and application of these instructions ............................................................. 2
1.3Explanation of symbols and signs ................................................................................................................... 2
2Product information ........................................................................................................... 4 
2.1Parts description.............................................................................................................................................. 4
2.2Technical data/accessories ............................................................................................................................. 4
2.3Intended use of product................................................................................................................................... 4
2.4Product identification ....................................................................................................................................... 4
2.5CE conformity.................................................................................................................................................. 4
3Operation of the ceiling roller blind.................................................................................... 5
3.1Ceiling roller blind with 230V electric drive ...................................................................................................... 5
4General safety instructions................................................................................................ 6
4.1Information on safety....................................................................................................................................... 6
4.2Safety instructions ........................................................................................................................................... 6
5Care/maintenance............................................................................................................. 7
5.1General information on care and maintenance of the roller blind .................................................................... 7
5.2Cleaning the roller blind................................................................................................................................... 7
5.3Maintenance of the roller blind ........................................................................................................................ 8
6Warranty............................................................................................................................ 8
7Spare parts/repairs............................................................................................................ 8
8Dismantling/disposal ......................................................................................................... 8
9Troubleshooting ................................................................................................................ 9

Product information
[B867213_0] - EN/ 25.09.09 Page 4 of 12 Subject to change without notice.
2Product information
2.1 Parts description
dd200003407
1 Fabric shaft 5 Guide rail
2 Curtain 6 End cap
3 Spring-loaded shaft 7 Cover panel
4 Console
Fig. 1: Parts overview of ceiling roller blind
2.2 Technical data/accessories
Electric motor
Parameter Value
Rated torque 4 - 9 Nm
Revolutions 14 rpm
Mains voltage 230 V AC/50 Hz
Current consumption 0.35 - 0.5 A
Power consumption 65 - 100 W
Motor protection class IP 44
Short-term operation (S2) Approx. 4 minutes
Tab. 1: Electric motor data
Accessories
A wide range of control devices is optionally available for
our sun shading control systems to give you control of the
product.
2.3 Intended use of product
The WAREMA ceiling roller blind is an internal sun
shading system that may only be used as intended (use
as protection against summer light and glare and for
visual privacy of inside areas on vertical, sloped and
horizontal glass surfaces). Inappropriate use may result in
significant danger.
Do not place additional strain, such as that from suspend-
ed objects, on the WAREMA ceiling roller blind as this
may damage the product and is therefore not permitted.
Installation on emergency doors is also not permitted.
WAREMA will not be liable for any resulting damage.
The intended use also includes observing these instruc-
tions and the installation conditions.
2.4 Product identification
The product has a CE mark.
2.5 CE conformity
The product conforms to CE and meets the requirements
of the relevant European guidelines.
CE conformity is certified, and WAREMA holds the
corresponding declaration. To maintain this state and to
ensure that the product can be safely installed and put
into operation, you as the fitter must adhere to the
installation instructions.
Name: WAREMA Renkhoff SE
Year of declaration of conformity: 2009
Head
office:
Hans-Wilhelm-Renkhoff-Strasse 2
97828 Marktheidenfeld
Germany
Standard: DIN EN 60335-2-97
Product: Roller blind
Intended use: For inside installation
Noise emission level1: < 70dB (A)
1In a standard installation of the product on a test stand, the
noise emission level is <70 dB(A). This value may vary de-
pending on the installation.

Operation
[B867213_0] - EN/ 25.09.09 Page 5 of 12 Subject to change without notice.
3Operation of the ceiling roller blind
3.1 Ceiling roller blind with 230V electric drive


NOTE
The product can be stopped in any position.


NOTE
The limit stop of the product is restricted in both
directions, i.e. the product is automatically stopped
at this point.
Retracting and extending with rotary switch or push
button
Retracting and extending with snap-in switch
dd200003408
Press and hold the button
(UP) or the button (DOWN)
or
Turn the rotary switch to the
left or right and hold.
The product moves in the
selected direction. The
movement stops when the push
button or rotary switch is
released.
dd200003408
Press the button (UP) or
the button (DOWN) or
Turn the rotary switch to
the left or right.
The product moves in the
selected direction. The
movement is stopped by
pressing the stop button,
pressing the button for the
opposite direction or returning
the rotary switch.
Extending/retracting with automatic control Information for motor runtime
Instructions on how to operate this feature are contained in a
separate manual.
A wide range of control devices is available for our sun
protection systems to give you optimum control of the
product. Please contact your qualified specialist for further
information.
CAUTION
Product damage!
Set the automatic control to manual if you
are going to be away.
The motors used in these products are not intended for
continuous operation. The integrated thermal protection will
switch the motor off after approx. 4 minutes. The product will
be ready for use again after approx. 10-15 minutes.

General safety instructions
[B867213_0] - EN/ 25.09.09 Page 6 of 12 Subject to change without notice.
4General safety instructions
4.1 Information on safety
The following safety instructions and warnings are
intended to safeguard your health as well as protect the
product. Please read the following points carefully.
Damage resulting from inappropriate use or the failure to
observe these instructions or safety information is not
covered by the guarantee. Liability will not be accepted
for consequential damage!
4.2 Safety instructions
Gust General operation of the roller blind
dd200003409
With the window open or tilted,
a sudden draft can damage the
product or other property.
dd200003410
Only operate the product
if it is in technically per-
fect condition.
If damaged, stop
operation immediately
and inform your dealer.
Limit access to the control elements Risk of crushing/injury
dd200003411
Do not let children play with
the operating element, e.g.
the hand-held transmitter.
Keep the hand-held
transmitter away from chil-
dren.
dd200003412
Do not reach into
moving parts (e.g. end
rod) when the product is
retracted or extended.
Keep the projection area
of the product clear of
obstacles/persons.
The minimum clearance
of 2500 mm between the
product and the ground
must be maintained. If
the minimum clearance
is undershot, suitable
safety measures must
be implemented on site
(e.g. shielding or push
button operation within
sight of the product).

Care/maintenance
[B867213_0] - EN/ 25.09.09 Page 7 of 12 Subject to change without notice.
5Care/maintenance
5.1 General information on care and
maintenance of the roller blind
Proper and regular care and maintenance and the use of
original spare parts only are essential for fault-free
operation and a long product life.
DANGER
Risk of injury from operation of the product
when it is out of view.
Disconnect the product from the automatic
control and/or de-energise it.


NOTE
Ensure that the product is not moved during
maintenance and repair work in its direct proximity –
e.g. window-cleaning.
De-energise the product.
CAUTION
Risk of injury due to static charge.
Contact with persons or objects may result in
electrostatic discharge from statically charged
fabric.
DANGER
Risk of injury and falling!
Do not rest climbing aids against the
product.
Climbing equipment must rest on a solid
foundation and offer good support!
CAUTION
Product could be damaged by incorrect
cleaning!
Do not use high pressure washers,
abrasive cleansers, abrasive sponges or
solvents such as alcohol or naphtha.
Do not support yourself on the product or
parts of the product.
5.2 Cleaning the roller blind
To ensure the longest possible
life, we recommend you clean
the surface of the product
regularly and at least once a
year.
If the first cleaning takes place
years after initial installation,
the product cannot be returned
to its original condition.
Replacement claims cannot be
honoured on the grounds of
these cleaning and care
instructions because the
effectiveness of these
measures depends on a large
number of factors that vary
from case to case.
Clean the roller blind regularly. Follow the procedure
described in the following table.
Cleaning procedure
Use a suitable cleaning agent to clean the
aluminium surfaces (e.g. common household
cleansers or cleaning agents).
Remove any dust and/or dirt from the fabric or
the guide rails.
Wash the fabric with a mild detergent (water
max. 30°C).2
Remove soiling on the fabric with a colourless
eraser.1
Brush the fabric (only coated polyester fabrics).1
Wipe off the fabric using a moist cloth.1
Inspect the operating elements, lifting tapes and
motor line for visible wear and damage.
Check that the roller blind is functioning properly.
Watch the product as it travels the full projection
range and look for any unusual behaviour or noises.
Have any damage repaired by a qualified specialist
as soon as possible.
2Depending on the fabric type.

Maintenance/Warranty/repair/dismantling
[B867213_0] - EN/ 25.09.09 Page 8 of 12 Subject to change without notice.
5.3 Maintenance of the roller blind
The product must be main-
tained regularly and at least
once a year.
Inspection and maintenance
work is only to be carried out
by an appropriately qualified
specialist. We recommend you
take out a maintenance
agreement with a qualified
specialist.
DANGER
Risk of injury through irregular maintenance!
Check the unit regularly for signs of wear
and damage, e.g. on the motor line.
Do not use systems in need of repair.
DANGER
Electric shock!
When inspecting or maintaining electrical parts,
the power connection must be de-energised
and locked out.
Check the product for visible wear, for damage to
the motor line and to ensure it is securely attached
(e.g. check that screws have a firm hold).
Check the function and the switch-off points on the
product.
Replace the battery in units with remote controls.
6Warranty
Subject to the statutory period of limitation for warranty
claims. This requires regular maintenance. The warranty
does not include wear parts or optical changes in line
with the type of material used (e.g. bleaching of surfaces
caused by UV rays).
Wear parts are
Bearing parts
Runners/sliders
Lifting tapes
7Spare parts/repairs
CAUTION
Personal injury or property damage resulting
from inappropriate repairs.
The product should only be repaired by a
specialist.
To ensure that your roller blind will operate properly on a
continuous basis and to avoid changing its approved
status, use WAREMA spare parts only. Please contact a
qualified specialist for further information.
8Dismantling/disposal
CAUTION
Personal injury or property damage resulting
from inappropriate disassembly.
The product should only be dismantled by a
specialist.
Disassembly and re-installation of the product must be
undertaken by a qualified specialist in accordance with
current guidelines and standards. Be sure to ask the
manufacturer for any missing documents before com-
mencing disassembly or re-installation.
Should the product no longer be required, ensure that it
is disposed of correctly in accordance with the relevant
regulations.

Troubleshooting
[B867213_0] - EN/ 25.09.09 Page 9 of 12 Subject to change without notice.
9Troubleshooting
CAUTION
Injury or damage to persons or property
resulting from troubleshooting.
Problems with no reference to a qualified
specialist may be rectified independently.
Other problems are only to be dealt with by
a qualified specialist.
Problem Possible causes Remedy
Motor is not operating. Motor is malfunctioning. Motor change (specialist only)
On-site motor connection is incorrect. Reconnect as per wiring diagram (certified
electricians only)
Motor thermal protection switch has
triggered
Wait 10 to 15 minutes, then try again
There is no current Check the power fuse (certified electricians
only)
A higher-level control command is
present
Await switch on/off delay
End rod does not move
to limit positions
Motor switch-off positions are incorrect Readjust the motor (specialists only)
Soiling is obstructing the guide rail
chambers
Remove soiling
Motor limit positions were lost Readjust the limit positions (qualified
specialists only)
The bottom rail is at a
slant/curtain is wavy
Lifting tape is torn Replace the lifting tape (specialists only)
Guide rails are not parallel Adjust the guide rails according to specifica-
tion (specialists only)
Tab. 2: Overview of possible problems

[B867213_0] - EN/ 25.09.09 Page 10 of 12 Subject to change without notice.

[B867213_0] - EN/ 25.09.09 Page 11 of 12 Subject to change without notice.

This technical documentation contains copyrighted company
information. All rights reserved.
The information in this documentation and the product itself
are subject to change without notice. All brands and product
names mentioned in this documentation are trademarks or
registered trademarks of the respective holder.
Considerable care was taken in producing the text and
graphics in this documentation. No liability is accepted for
any errors which may nevertheless exist in this documenta-
tion nor for the consequences of any such errors.
Company stamp
© 2009, WAREMA Renkhoff SE, Hans-Wilhelm-Renkhoff-Straße 2, 97828 Marktheidenfeld, Germany
http://www.warema.de E-mail: [email protected]e