Warmlite WL45033 User manual

www.warmlite.co
2000W
WALL MOUNTED SURROUND
FIREPLACE SUITE
MODEL WL45033
YOUR SAFETY &
INSTRUCTION MANUAL
PLEASE READ CAREFULLY

2
CUSTOMER SUPPORT TEAM:: [phone]
TECHNICAL DATA
Description: Wall Mounted Surround Fireplace Suite
Model: WL45033
Rated Voltage: 220 - 240V
Frequency: ~ 50/60Hz
Power consumption: 2000W
Remote Control: 1 x 3V lithium button cell battery
DOCUMENTATION
We declare that this product conforms to the following product legislation in accordance with the
following directive(s):
2014/30/EU Electromagnetic Compatibility Directive.
2014/35/EU Low Voltage Directive.
2011/65/EU Restriction of Hazardous Substances Directive.
RK Wholesale LTD Quality Assurance, United Kingdom
WARRANTY
This product is guaranteed for 12 months from the date of original purchase. If any defect arises due
to faulty materials of workmanship, the faulty products must be returned to the place of purchase.
Refund or replacement is at the discretion of the retailer.
The following conditions apply:
• The product must be returned to the retailer with proof of purchase.
• The product must be installed and used in accordance with the instructions contained in this
instruction guide.
• It must be used only for domestic purposes.
• It does not cover wear and tear, damage, misuse or consumable parts.
• RK Wholesale LTD has limited liability for incidental or consequential loss or damage.
• This guarantee is only Valid in the UK and Eire Only.
An extended warranty is available for this appliance.
See back page for details.

3
www.warmlite.co
WIRING SAFETY FOR UK USE ONLY
IMPORTANT
As the colours in the
mains lead of this
appliance may not
correspond with the
coloured markings
identifying the terminals
in your plug, please
proceed as follows:
The wires in the mains lead are coloured in
accordance with the following code:
Blue neutral [N] Brown live [L]
Green/Yellow [EARTH]
Plug Fitting Details (Where Applicable).
The wire coloured blue is the neutral and must
be connected to the terminal marked [N] or
coloured black.
The wire coloured brown is the live wire and
must be connected to the terminal marked [L] or
coloured red.
The wire coloured green/yellow must be
connected to the terminal marked with the letter
[E] or marked .
On no account must either the brown or the blue
wire be connected to the [EARTH] terminal .
Always ensure that the cord grip is fastened
correctly.
The plug must be tted with a fuse of the same
rating already tted and conforming to BS 1362
and be ASTA approved.
If in doubt consult a qualied electrician who will
be pleased to do this for you.
Non-Rewireable Mains Plug
If your appliance is supplied with a non-
rewireable plug tted to the mains lead and
should the fuse need replacing, you must use an
ASTA approved one (conforming to BS 1362 of
the same rating).
If in doubt, consult a qualied electrician who will
be pleased to do this for you.
If you need to remove the plug – disconnect
it from the mains – and then cut it o of the
mains lead and immediately dispose of it in a
safe manner. Never attempt to reuse the plug or
insert it into a socket outlet as there is a danger
of an electric shock.
WARNING:
This Appliance MUST be Earthed
FUSE

4
CUSTOMER SUPPORT TEAM:: [phone]
PRODUCT SAFETY
When using any electrical appliance, basic safety precautions should
always be followed including the following:
• Check that the voltage of the
main circuit corresponds with
the rating of the appliance
before operating.
• Please ensure that the
appliance is used on a stable,
level, and heat resistant
surface.
• DO NOT immerse cords, plugs
or any part of the appliance in
water or any other liquid.
• DO NOT leave the appliance
unattended while it is operating.
• Close supervision is necessary
when any appliance is used by
or near children.
• Take care when any appliance
is used near pets.
• This appliance can be used
by children aged from 8 years
and above and persons with
reduced physical, sensory or
mental capabilities or lack of
experience and knowledge
if they have been given
supervision or instruction
concerning use of the appliance
in a safe way and understand
the hazards involved.
• Children should not play with
the appliance.
• Cleaning and user maintenance
should not be undertaken by
children without supervision.
• Switch o at the wall socket
then remove the plug from
the socket when not in use or
before cleaning.
• If the supply cord or appliance
is damaged, stop using the
appliance immediately and seek
advice from the manufacturer,
its service agent or a similarly
qualied person.
• DO NOT let the cord hang over
the edge of a table or counter
or let it come into contact with
any hot surfaces.
• The use of accessory
attachments other than those
supplied is not recommended.
• DO NOT pull the plug out by
the cord as this may damage
the plug and/or the cable.
• DO NOT use this product for
anything other than its intended
use.
• This appliance is for household
use only.
• DO NOT carry the appliance by
the power cord.

5
www.warmlite.co
• DO NOT use any extension
cord with this appliance.
• DO NOT use the appliance
outdoors.
• This heater is not equipped with
a device to control the room
temperature. DO NOT use this
heater in small rooms when
they are occupied by persons
not capable of leaving the room
on their own, unless constant
supervision is provided.
• Always ensure that the heater is
placed on a rm level surface.
• Ensure that the heater is not
positioned close to curtains,
furniture or any combustible
materials as this could create a
re hazard.
• Never sit or stand on the re.
• Never cut o the plug and hard
wire into a xed fused spur.
• The heater must not be located
immediately below a mains
socket outlet.
• DO NOT cover the heater as
this may lead to a re risk.
• DO NOT obstruct any of the
openings of the heater.
• DO NOT insert any object
through any openings on the
heater.
• Check the heater from time to
time for accumulated dust.
• DO NOT use the heater in
areas where ammable liquids
are stored or where ammable
fumes may be present.
• DO NOT cover the cord under
the carpeting. DO NOT cover
with throw rugs, runners or the
like. Arrange the cord away
from trac areas and where it
could be tripped over.
• This appliance has hot and
arcing or sparking parts inside.
DO NOT use it in areas where
gasoline, paint or ammable
liquids are used or stored.
• This replace should not
be used as a drying rack
for clothing. DO NOT hang
Christmas stockings or other
decorations on or near this
product.
• DO NOT operate the heater on
a timer, or leave on overnight.
• When not being used, please
unplug the heater from the
mains socket.

6
CUSTOMER SUPPORT TEAM:: [phone]
• Keep the mains lead away from
the hot body of the heater and
ensure that it is not pulled tight
between the socket and the
heater.
• Always unplug the heater and
allow it to cool before moving it
from one location to another.
• WARNING! This product must
be installed correctly, failure
to do so may cause damage
to your product and/or your
surroundings.
• DO NOT attempt to dismantle
or repair any part of the heater.
• This should only be done by a
qualied service agent.
• In the unlikely event the
appliance develops a fault,
stop using it immediately and
seek advice from the Customer
Support Team.
HIGH VOLTAGE HOT SURFACE DO NOT COVER

7
www.warmlite.co
21
3
4
WHAT’S IN THE BOX
Instruction Manual
Wall Fire Suite
Remote
Log set
Fixing/Mounting Screws
1. Heater
2. Surround
3. Log Set
4. Remote Control
BEFORE YOUR FIRST USE:
1. Remove your appliance from the packaging.
2. Install your appliance in accordance with the installation & safety instructions.
3. Your appliance is now ready for normal use.
Dispose of the packaging in a responsible manner.
WARNING: This product must be installed correctly, failure to do so may result in injury, electric
shock to the user or damage to your product and your Property.
TOOLS NEEDED (not supplied)
1. 2mm pilot drill bit & 8mm drill bit (the 8mm drill bit may need to be a masonry bit)
2. Philips screw driver
3. Power drill
2mm
8mm

8
CUSTOMER SUPPORT TEAM:: [phone]
HANDLING
Before continuing any further with the
installation of this re please read the following:
• Two people should be sucient to lift the
re.
• When lifting always keep your back
straight. Bend your legs and not your
back.
• Avoid twisting at the waist. It is better to
reposition your feet.
• Avoid upper body / top heavy bending.
Always bend from the knees rather
than the waist. Do not lean forward or
sideways whilst handling the re.
• Always grip with the palm of your hand.
Do not use the tips of ngers for support.
• Always keep the product as close to the
body as possible to prevent unnecessary
and undue strain on the body.
• Use gloves to provide additional grip.
• Always use assistance if required.
UNPACKING THE PRODUCT
The unit is supplied in a single package
carton. Carefully unpack the product using the
following procedure:
• Ensure that the product is in the correct
position with the carton wording legible.
• Remove the straps and sleeve.
• Carefully lift the replace out of the box.
• Remove the protective packaging and
bag from the suite.
• Locate the xing pack and put aside.
• Carefully remove the protective lm
covering the re.
INSTALLATION
IMPORTANT: Do not connect the appliance
until it is properly xed to the wall and the
instructions have been read fully.
Ensure the minimum distances are
observed.
1. The re is designed to be permanently
xed to a wall at a minimum height
of 300mm. The wall bracket must be
tted horizontally and the cable routed
to the bottom right of the re. A height
of 600mm from the oor to the bottom
of the wall re is recommended for
optimum viewing of the fuel bed.
2. Use the bracket as a table template
and mark ve drill positions on the wall.
Ensure that these holes are all level.
3. Put the bracket aside and drill holes
with a depth of 35mm using a 2mm
pilot drill bit & 8mm drill bit.
4. Clean the holes from dust and debris
and insert one plug in each hole. Make
sure the edge of each hole is ush with
the surface.
5. Hold the bracket in position and x it in
place with screws.
475 mm
330.5 mm

9
www.warmlite.co
6. Carefully lift the appliance up, ensuring
that the top rear ledge of wall re
engages with the wall bracket and is
sitting centrally. This process should be
carried out by two people to avoid injury
or damage to property or the appliance.
Do not let go of the appliance until
you are sure it is safely attached to the
bracket.
7. Gently bring the wall re down against
the wall. Mark the lower xing brackets
two xing hole positions on the wall,
then remove the wall re.
8. Drill the wall and insert the wall plugs.
9. Ret the wall re to the wall and
fasten the bottom xing bracket to
the wall using the screws provided to
permanently x the wall re in place.
10. Remove the front panel and unpack the
logs from the bag and place them along
the light unit in the desired position.
11. Put the front panel back in place.
USING YOUR APPLIANCE
Helpful advice before tting:
The appliance can be operated either by the
switches located on the left hand side of the
re under its canopy or by the supplied remote
control.
MANUAL OPERATION
The On/O switch is must be switched to ‘I’ to
begin operating the re.
Operation is via by the buttons located on the
left hand side of the re under the canopy.
The re will beep to indicate that it is powered
up.
• Turn on the appliance by pressing the
Power switch on the main unit.
• To activate the ame eect, press the
Flame button. The indicator light will
illuminate, this can be activated without
the heater operating.
• Press once for a low brightness setting,
the next two presses of the button will
increase the brightness.
• A fourth press of the button will switch the
ame eect o.
• The fan heater has two separate settings
that are selected by pressing each
Function button.
• Pressing Button One selects the 1000W
heat setting, the Heat 1 display will
illuminate.
• Pressing Button Two selects the 2000W
setting, the Heat 2 display will illuminate.
• To turn the heater o press the Function
button again and set the power switch
to 0.
REMOTE OPERATION
Press once to turn the appliance
and ame eects on. Pressing
again turns the appliance and
ame eects o.
Press to cycle through the three
ame eect settings.
Time calibration settings. If not
set the timer eect will start from
00:00.
Press once to reduce the light
brightness. Pressing again turns
the light o.
Press once to activate 1000W
heat, pressing twice activates
2000W. Pressing again will turn o
the heating.
Open window On/O.
Press to turn the Timer settings
On/O.
Timer setting. You can set two
time periods and temperature
which set using the

10
CUSTOMER SUPPORT TEAM:: [phone]
• Ensure the re’s power switch is set to On.
• Using the remote control, press the
Flame button or power button to enable
the ame eect function. The rst press
activates the low brightness setting, the
next two button presses will increase
the brightness, and a fourth press of the
button will switch the unit o.
• The Fan heater has two separate settings
that are selected by pressing the Heater
button.
• The rst press selects the 1000W heat
setting, the Heat 1 display will illuminate.
The second press selects the 2000W
setting, the Heat 2 display will illuminate.
• Press the POWER button to switch the
appliance On and O.
SAFETY CUT-OUT
This appliance is tted with a safety cut-o
which will operate if the re overheats (e.g. due
to blocked air vents). For safety reasons, the
re will NOT automatically reset.
To reset the appliance, disconnect the
appliance from the mains supply for at least 15
minutes. Reconnect to the mains supply and
switch on the appliance.
CAUTION: Do not touch the heater as it will be
hot. Set the heater switches to OFF and leave
the heater to cool down fully. Once completely
cool, reconnect the heater and switch it on.
Do not open this product. There are no user-
serviceable parts inside.
CHECK THAT YOU HAVE NOTED ALL THE
FOLLOWING INSTRUCTIONS:
Do’s
• Always install the re in accordance with
this guide. If in doubt obtain expert advice.
• Always make sure the electrical socket is
accessible and located adjacent to, but
not above or behind the re.
• Always disconnect the re from the
electrical supply before carrying out
cleaning or maintenance.
• Always make sure the re is rmly
secured.
• Always assemble the re in accordance
with this guide. If in doubt, obtain expert
advice.
• Always ensure the product is assembled
in an area that is free from dust, grease or
liquids.
• Always ensure that the correct tools are
used to assemble/install this product.
• Always make sure the re is rmly secured
in place when complete.
Dont’s
• Never leave children unsupervised in a
room where the re is ON and unguarded.
• Never obstruct or cover the fan outlet or
force items into re openings.
• Never install or use the re anywhere
where water is in use, i.e. bathrooms,
kitchens, shower rooms, and swimming
pool etc.
• Never use aerosols or steam cleaners on
or around the re.
• Never route the mains supply cable under
carpet etc.
• Never install the re close to curtains or
combustible materials.
• Never use the re to dry clothes etc.
• Never sit or stand on the re.
• Never cut the o the plug and hard wire
into a xed fused spur.
Note: Any new wiring required, must be in
accordance with local and national codes and
other applicable regulations in order to reduce
the risk of re, electric shock, or other injuries.
Note: When the re is turned on for the rst
time or when it has not been used for some
time, it may release a slight, harmless odour.
This odour is a normal occurrence caused
by the initial heating of the internal heating
elements or dust, and will disappear with use.

11
www.warmlite.co
TROUBLE SHOOTING
Safety Cut-Out device:
To ensure against the potential hazard
caused by blockage of the air outlet, this
unit is equipped with an automatic over-
temperature safety cut-out device. When the
device is activated the heater will not operate.
If this occurs, the unit can be reset using the
following procedure.
1. Turn the re o by depressing the on/o
switch on the unit.
2. Unplug the power cord form the electrical
mains supply socket and leave it
disconnected for at least 15 minutes.
3. Ensure that the air vents are free from
obstruction.
4. Plug the power cord back in to the mains
socket.
5. Turn the re back on.
6. If the re fails to operate, check the fuse
in the plug.
7. If the fuse in the plug is OK and the re
is still not functioning, contact a qualied
service person.
Symptom Corrective action
No operation/ no
fan.
Check that the
safety cut-o has
not operated.
Check the fuse;
if broken a
replacement is
necessary.
No light Check the LED,
if broken a
replacement is
necessary.
CLEANING AND CARE
• Warning- Always disconnect from the
mains supply before cleaning the wall re.
• For general cleaning use a soft clean
duster - never use harsh abrasive or
cleaners.
CAUTION: Allow the product to completely
cool before handling or cleaning it.
• Do not allow water or other liquids to run
into the interior of the product, as this
could cause a re and/or electrical hazard.
• We also recommend the periodic cleaning
of this appliance by lightly running a
vacuum cleaner nozzle over the guards
to remove any dust or dirt that may have
accumulated inside or on the unit.
CAUTION: Do not use harsh detergents,
chemical cleaners or solvents as they may
damage the surface nish of the plastic
components.
WARNING:
DO NOT IMMERSE ANY ELECTRICAL PART
OF THE APPLIANCE IN WATER SUCH AS
MOTOR UNITS OR PLUGS.
PLEASE SEE CLEANING SECTION FOR
FURTHER INSTRUCTIONS.
DISPOSAL OF THE UNIT
Appliances bearing the symbol shown here
may not be disposed of in domestic rubbish.
You are required to dispose of old electrical
and electronic appliances like this separately.
Please visit www.recycle-more.co.uk or
www.recyclenow.co.uk
for access to information about the recycling
of electrical items.
Please visit www.weeeireland.ie for access to
information about the recycling of electrical
items purchased in Ireland.
The WEEE directive, introduced in August
2006, states that all electrical items must be
recycled, rather than taken to landll.
Please arrange to take this appliance to your
local Civic Amenity site for recycling, once it
has reached the end of its life.

We hope you enjoy your appliance for many years.
As a thank you for purchasing one of our fantastic products,
we are oering you an extra 1 year peace of mind.
*To receive your extra guarantee period, register your appliance online
within 28 days of purchase by visiting:
www.warmlite.co
Make sure to retain your original receipt.
Should you have a problem
with your appliance or need any spare parts please call our
Customer Support Team on:
[phone]
Distributed throughout the UK by RK Wholesale LTD
0218.V2