Warmlite WL45038 User manual

www.warmlite.co
GLASS WALL MOUNTED
FIREPLACE
WL45038
YOUR SAFETY &
INSTRUCTION MANUAL
PLEASE READ CAREFULLY

2
CUSTOMER SUPPORT TEAM: [phone]
TECHNICAL DATA
Description: Glass Wall Mounted Fireplace
Model: WL45038
Rated Voltage: 220-240V
Frequency: 50Hz
Power Consumption: 2000W
DOCUMENTATION
We declare that this product conforms to the following product legislation in accordance with the
following directive(s):
2014/30/EU Electromagnetic Compatibility Directive.
2014/35/EU Low Voltage Directive.
2011/65/EU Restriction of Hazardous Substances Directive.
2009/125/EC Eco-Design of Energy Related Products.
RK Wholesale LTD Quality Assurance, United Kingdom
WARRANTY
This product is guaranteed for 12 months from the date of original purchase. If any defect arises due
to faulty materials of workmanship, the faulty products must be returned to the place of purchase.
Refund or replacement is at the discretion of the retailer.
The following conditions apply:
• The product must be returned to the retailer with proof of purchase.
• The product must be installed and used in accordance with the instructions contained in this
instruction guide.
• It must be used only for domestic purposes.
• It does not cover wear and tear, damage, misuse or consumable parts.
• RK Wholesale LTD has limited liability for incidental or consequential loss or damage.
• This guarantee is only Valid in the UK and Eire Only.
An extended warranty is available for this appliance.
See back page for details.

3
www.warmlite.co
WARNING:
This Appliance MUST be Earthed
WIRING SAFETY FOR UK USE ONLY
IMPORTANT
As the colours in the mains lead of this appliance
may not correspond with the coloured markings
identifying the terminals in your plug, please
proceed as follows:
The wires in the mains lead are labelled in
accordance with the following code:
Blue neutral [N] Brown live [L]
Green/Yellow [EARTH]
Plug Fitting Details (Where Applicable). The
wire labelled blue is the neutral and must be
connected to the terminal marked [N].
The wire labelled brown is the live wire and must
be connected to the terminal marked [L].
The wire labelled green/yellow must be
connected to the terminal marked with the letter
[E].
On no account must either the brown or the blue
wire be connected to the [EARTH] terminal.
Always ensure that the cord grip is fastened
correctly.
The plug must be tted with a fuse of the same
rating already tted and conforming to BS 1362
and be ASTA approved.
If in doubt consult a qualied electrician who will
be pleased to do this for you.
Non-Rewireable Mains Plug
If your appliance is supplied with a non-
rewireable plug tted to the mains lead and
should the fuse need replacing, you must use an
ASTA approved one (conforming to BS 1362 of
the same rating).
If in doubt, consult a qualied electrician who will
be pleased to do this for you.
If you need to remove the plug - disconnect it
from the mains - then cut it o of the mains lead
and immediately dispose of it in a safe manner.
Never attempt to reuse the plug or insert it into a
socket outlet as there is a danger of an electric
shock.
FUSE
Earth
(Green/Yellow)
Fuse
Neautral
(Blue)
Live
(Brown)

4
CUSTOMER SUPPORT TEAM: [phone]
PRODUCT SAFETY
When using any electrical appliance, basic safety precautions should
always be followed including the following:
• Check that the voltage of the
main circuit corresponds with
the rating of the appliance
before operating.
• The intended use for this unit
is described in this manual.
The use of any accessory
or attachment or the
performance of any operation
with this appliance other
than those recommended in
this instruction manual may
present a risk of personal
injury.
• Retain this manual for future
reference.
• WARNING! When using
mains-powered appliances,
basic safety precautions,
including the following,
should always be followed to
reduce the risk of re, electric
shock and personal injury
and material damage.
• Check that the voltage of the
main circuit corresponds with
the rating of the appliance
before operating.
• Always ensure that the
appliance is placed on a rm
level surface. Ensure that the
air cooler is not positioned
close to curtains, furniture or
any combustible materials
as this could create a re
hazard. The appliance must
not be located immediately
below a mains socket outlet.
• DO NOT immerse cords,
plugs or any part of the
appliance in water or any
other liquid.
• DO NOT let the cord hang
over the edge of a table
or counter or let it come
into contact with any hot
surfaces.
• DO NOT carry the appliance
by the power cord.
• DO NOT use any extension
cord with this appliance.
• The use of accessory
attachments is not
recommended by the
appliance manufacturer,
apart from those supplied
with this product. DO NOT
use extension cords with the
appliance.
• DO NOT pull the plug out by
the cord as this may damage
the plug and/or the cable.
• Switch o at the wall socket
then remove the plug from
the socket when not in use
or before cleaning.

5
www.warmlite.co
• Switch o and unplug before
tting or removing tools/
attachments, after use and
before cleaning.
• DO NOT use this product
for anything other than its
intended use.
• DO NOT leave the appliance
unattended while it is
operating.
• This appliance is for
household use only.
• DO NOT use the appliance
outdoors.
• DO NOT use the appliance
near water.
• Always place wires in a
regular and orderly manner
to prevent the air cooler from
becoming a trip hazard or
the plug from accidentally
being pulled out.
• The heater must not be
located immediately below a
socket outlet.
• Do not use this heater in
the immediate surroundings
of a bath, a shower or a
swimming pool.
• In order to avoid overheating,
do not cover the heater.
• Children of less than 3 years
should be kept away unless
continuously supervised.
• Children between the ages of
3 and 8 years old should only
switch the appliance on or
o when it has been placed
and installed in its intended,
normal operating position
and when they have been
given adequate supervision
or instruction concerning
safe use of the appliance
and understand the hazards
involved. Children between
the ages of 3 and 8 years
old should not plug in,
regulate, clean or perform
user maintenance on the
appliance.
• The appliance is not to be
used by persons (including
children) with reduced
physical, sensory or mental
capabilities, or lack of
experience and knowledge,
unless they have been given
supervision or instruction.
• Close supervision is
necessary when any
appliance is used by or near
children.
• Children should not play with
the appliance.

6
CUSTOMER SUPPORT TEAM: [phone]
• This appliance can be
used by children aged
from 8 years and above
and persons with reduced
physical, sensory or mental
capabilities or lack of
experience and knowledge
if they have been given
supervision or instruction
concerning use of the
appliance in a safe way and
understand the hazards
involved.
• CAUTION! Some parts of
this product can become
very hot and cause burns.
Particular attention has to
be given where children
and vulnerable people are
present.
• Cleaning and user
maintenance should not
be undertaken by children
without supervision.
• Take care when any
appliance is used near pets.
• When not in use, please
unplug the portable air cooler
from the mains socket.
• Always unplug the appliance
and allow it to cool before
moving it from one location
to another.
• Please ensure that the
appliance is used on a
stable, level, and heat
resistant surface.
• If the supply cord or
appliance is damaged,
stop using the appliance
immediately and seek advice
from the manufacturer, its
service agent or a similarly
qualied person.
• DO NOT attempt to
dismantle or repair any part
of the heater. This should
only be done by a qualied
service agent.
• DO NOT install the heater in
washhouses or other places
with water and moist.
• DO NOT turn the heater on
or o by inserting or pulling
out the plug.
• DO NOT place things on the
heater.
• DO NOT put anything into
the air inlet and outlet.
• DO NOT use insecticide
spray or other ammable
matters in the vicinity of the
heater.
• DO NOT splash oil or water
into the heater.

7
www.warmlite.co
• DO NOT clean the heater
with water. Wipe it with a
semi-wet soft cloth.
• DO NOT wipe the heater with
chemical solvents such as
benzene, gasoline or alcohol.
Use neutral detergents only.
• Only install the heater in at
and dry places. Keep the
heater 50cm away from
surrounding objects.
• The heater should be placed
away from gasoline, cooking
stoves or other combustibles
and heat sources.
• Use the appliance in a well-
ventilated area.
• CAUTION! DO NOT operate
the appliance with wet
hands.
• DO NOT tip the appliance
over as this may cause
damage to the appliance and
create a re hazard.
• In the unlikely event the
appliance develops a fault,
stop using it immediately
and seek advice from the
Customer Support Team.
HIGH VOLTAGE HOT SURFACE DO NOT COVER

8
CUSTOMER SUPPORT TEAM: [phone]
WHAT’S IN THE BOX
Instruction Manual
Fireplace
Wall Fixing Bracket
Wall Mounting Kit
Decorative Pebbles
Remote Control
1. Fireplace
2. Digital Display
3. Control Panel
4. Flame Eect
5. Pebbles
6. LED strip lights
BEFORE YOUR FIRST USE:
1. Remove your appliance from the packaging.
2. Install your appliance in accordance with the installation & safety instructions.
3. Your appliance is now ready for normal use.
Dispose of the packaging in a responsible manner.
1
4 5
2 3
6

9
www.warmlite.co
HANDLING
Before continuing any further with the
installation of this re please read the following:
• Two people should be sucient to lift the
re.
• When lifting always keep your back
straight. Bend your legs and not your
back.
• Avoid twisting at the waist. It is better to
reposition your feet.
• Avoid upper body / top heavy bending.
Always bend from the knees rather
than the waist. Do not lean forward or
sideways whilst handling the re.
• Always grip with the palm of your hand.
Do not use the tips of ngers for support.
• Always keep the product as close to the
body as possible to prevent unnecessary
and undue strain on the body.
• Use gloves to provide additional grip.
• Always use assistance if required.
UNPACKING THE PRODUCT
The unit is supplied in a single package
carton. Carefully unpack the product using the
following procedure:
• Ensure that the product is in the correct
position with the carton wording legible.
• Remove the straps and sleeve.
• Carefully lift the replace out of the box.
• Remove the protective packaging and
bag from the suite.
IMPORTANT: Always ensure there is enough
room to place it.
Please ensure that there is an accessible
electrical socket within the space for
installation. The electrical socket must not be
behind or above the suite.
INSTALLATION
This appliance is designed to be permanently
xed to a wall at a minimum height of 30cm.
The wall bracket must be tted horizontally
and the cable routed to the bottom right of the
heater. It is recommended that the distance
between the bottom of the replace and the
oor is of at least 60cm.
To wall-mount the replace, carry out the
following instructions:
1. Using the bracket as a template, mark
ve drill positions on the wall. Make
sure these holes are level. Observe the
recommended xing dimensions.
2. Put the bracket aside and drill holes with a
depth of 35 mm using an 8 mm drill bit.
3. Clean the holes thoroughly and insert one
plug in each hole. Make sure the edge of
each plug is ush with the surface
4. Hold the bracket in position and x it with
screws.
5. Attach the xing angle to the bottom of
the appliance using the short screws.
6. Carefully lift the appliance and hook it to
the wall bracket. DO NOT let go of the
appliance until you are sure it is safely
engaged to the bracket, as this could
cause you physical harm as well as
damage the appliance.
7. Now mark the hole position for xing the
angle. Carefully remove the appliance from
the bracket and once again drill holes with
a depth of 35 mm using an 8 mm drill bit.
8. Clean these new holes thoroughly and
insert one plug in each hole. Make sure
the edge of each plug is ush with the
surface
9. Lift the appliance up again, engage it to
the bracket and x the angle with screws.
IMPORTANT: Do not connect the appliance
until it is properly xed to the wall and the
instructions have been read fully.
Select a location that is not prone to moisture
and is located at least 36” away from any
combustible materials, such as curtain drapes,
furniture, bedding, paper, etc.

10
CUSTOMER SUPPORT TEAM: [phone]
Placing the Decorative Pebbles:
This unit comes complete with decorative
pebbles, to be placed on the inside of the
appliance.
To place the pebbles inside the re, begin by
opening the front panel. To do this, locate the
2 xing screws on either side of the unit, near
the bottom bracket, and use a screwdriver to
loosen them by turning them anti-clockwise (to
the left). Repeat this process with the 2 screws
on the opposite side of the replace, so that all
4 screws are loose.
When all 4 screws have been loosened, remove
them to one side and carefully pull the front
glass panel of the re away from the main body
of the unit. You can now place the decorative
pebbles inside the re.
Loosely scatter the pebbles over the main inner
area of the replace. Once you are happy with
the arrangement, place the front panel back
into position and insert the xing screws back
into their respective slots on either side of the
unit. Use a screwdriver to tighten each screw
into place by turning it clockwise (to the right).
so that the glass panel is secured and cannot
come loose.
NOTE: Ensure the glass panel is rmly secured
into place before attempting to use the re.
Your replace is now ready for use.
USING YOUR APPLIANCE
Turning the Appliance On and Off:
• To turn the appliance on, rst plug it into a
mains outlet.
• Once the appliance has been plugged
in, press the Power ON/OFF button on
the remote control or the unit’s control
panel to turn the appliance on. A red LED
indicator will light up to show the unit has
been turned on.
• Press this button again while the replace
is in operation to turn it o.
NOTE: When using the remote control, rst
ensure the Standby switch located on the top
right-hand side of the appliance is switched on;
otherwise, the remote operation function will
not work.
NOTE: When using the remote control to
operate the unit, there will be a delay between
the button press and the corresponding
function being activated. DO NOT press a
button more than once every two seconds to
ensure optimal operation.
Auto Function:
This replace is equipped with an Auto
function, in which the LED ame eect will
automatically change at 10-second intervals.
Long-press the Power ON/OFF button on the
remote control or the unit’s control panel to turn
the Auto ame function on.
Heat Selection:
This replace oers a choice of two heat
settings: Low (1000W) or High (2000W).
Each of these two settings is represented by
a corresponding button on the remote control
and the unit’s control panel.
To select your preferred heat settings, carry out
the following instructions:
• To select the Low heat setting, press the
1000W button on the remote control or
the unit’s control panel. Press this button
again to turn the heating function o.
• To select the High heat setting, press the
2000W button on the remote control or
the unit’s control panel. Press this button
again to turn the heating function o.
Setting The Time And Date:
• This unit is equipped with a built-in timer,
which allows for programmable, hands-
free timed operation. To make use of the
unit’s timer, begin by setting the correct
time and date.