Warmup 3IE User manual

Installation Guide:
for the Warmup 3iE Programmable Thermostat
3iE Installation Guide - 08/10 v1
© Warmup plc - 2010
Introduction:
The 3IE thermostat is designed to aid in the comfort of your home by providing timed regulation of your Warmup un-
deroor heating system. The thermostat is designed to receive temperature input signals from the following sensors:
1. Air sensor located inside thermostat
2. Floor sensor installed in oor to be heated (see Warmup heater instructions for details)
3. Optional 2nd sensor (either installed in oor or outside house)
The thermostat is not a safety device and should only be used with Warmup heating products. In order to avoid dam-
aging your ooring the correct oor type should be selected during the thermostat programming process.
Electrical Specication:
• Supply voltage: 230V +/-15% at 50Hz
• Thermostat is not designed for use with intermittent power supply.
• Maximum Switch Load: 16A resistive
• Standards: EN60730-1 & EN60730-2-9 standards
WARNING – important safety note
This product uses mains voltage electricity and work should only be carried out by a qualied electrician. You should
always isolate the power supply before attempting to install or repair the 3IE thermostat. The thermostat should not
be put into operation unless you are certain that the entire heating installation complies with current general safety
requirements for electrical installations. Electrical installation to be in accordance with latest IEE Wiring Regulations
and appropriate Statutory Regulations.
Location of Thermostat:
The thermostat should be installed inside a standard 55mm wall socket that is at least 30mm deep. For optimal per-
formance the thermostat should be located in an area with good ventilation. It should not be beside a drafty window/
door, in direct sun-light or above another heat generating device (e.g. radiator or TV).
The thermostat is designed for operation between 0°C and 55°C with relative humidity less than 80%.
Location and installation of oor sensor:
The optimum location of the oor sensor is described in each Warmup heater installation manual. Refer to that manual
when selecting oor sensor location.
A conduit has been provided with this 3IE thermostat. The use of this conduit will protect the sensor and will allow
easier repair of the sensor in the case of sensor damage after ooring has been laid.
When installing the oor sensor, it is recommended to use
the following process:
1. Work out the desired locations of the thermostat and
oor sensor. Measure distance of conduit required and
cut conduit to correct length. The end of the conduit
should be located somewhere easily accessible even
after all ooring material has been xed. It is recom-
mended to minimize the length of conduit and avoid
sharp corners.
2. Straighten both sensor cable and conduit. Push sen-
sor all the way through conduit and ensure the sensor
protrudes from the protective conduit by 3-4 cm.
3. Place metal cap over the sensor and then push back
ensuring a rm t between conduit and metal cap
Warning: Do not attempt to cut conduit with sensor in-
stalled. This could lead to irreparable damage to your
sensor.
Assembley of probe, conduit and metal cap
3 - 4 cm
____. ~
~ ~
~ :1 , w ?

Installation:
Separate the front housing of thermostat from wall module:
1. Un-screw both closing screws (bottom of stat) until they will not turn
any further.
2. Release front housing by gripping lower half of outer frame and pull-
ing outwards then upwards
3. Place front housing somewhere safe
4. Run all wires to the wall box. Check to ensure that you have included
the following:
• Power (Live and Neutral)
• Heater (Live and Neutral)
• Floor sensor
• Fil pilote (if necessary)
• External/ 2nd oor Sensor (if necessary)
5. Pull wires through wall box and complete terminal wiring.
IMPORTANT: Ensure that multi strand wires are fully inserted into the
terminal and secured tightly. Any loose strands should be trimmed as they
could cause a short-circuit.
Normal electrical installation (see numbering on diagram to right)
2. Connect to Power Supply (Live – MAX 240V)
3. Connect to Power Supply (Neutral – MAX 240V)
4. Connect to Warmup heater(s) (Neutral – MAX 3600W/ 16 Amps)
5. Connect to Warmup heater(s) (Live – MAX 3600W/ 16 Amps)
7. Connect to 1st wire of oor sensor (colour not important)
8. Connect to 2nd wire of oor sensor (colour not important)
Special installations:
(should only be performed under the supervision of Warmup)
Fil Pilote installation: (only for use in France)
1. Connect to l pilot (F.P.)
Second sensor installation: (2nd oor probe or exterior probe)
6. Connect to 1st wire of external sensor/ 2nd oor sensor
7. Connect to 2nd wire of external sensor/ 2nd oor sensor
Master/Relay installtion: (connecting 2 stats together)
6. Connect to terminal 6 on other thermostat
7. Connect to terminal 7 on other thermostat
Mounting thermostat into the wall box:
1. Push excess wire back through the wall box and insert thermostat
back module into wall box.
2. Put xing screws through mounting holes and tighten.
3. Ensure that thermostat is straight before tightening completely.
4. Replace thermostat front housing;
i) align and sit front housing on to hinges,
ii) push lower half of front housing until a ‘click’ is heard.
5. Ensure front housing is securely xed.
6. IMPORTANT: Tighten both retaining screws
0
,I )( A V
D c::::;
~ ~ ~ [
1 2 3 4 5
FP ,i ,i CE Yd
L N N L
2
ii~~G [Pi,~~~) ~Olk?.~
~XT lntertek
SENSOR
7 ~LARITY )
8
Warmup
3IE-01-BL
T55
< ~------------------~~- _/ /
, I
\\~57= - - - - - - -
/; =1
~ ~
· ~ ~
I
I
I
I
I
I
I
I

Powering-up:
You can now power up the thermostat and begin the programming process. An easy to follow menu will guide you
through the rest. If you want to turn on / off the thermostat and heating system then hold down the recessed button on
the bottom of the stat for 3 seconds
When you have ensured that both the oor sensor and heating elements are working correctly you can complete the
installation of oor covering and remove the protective cover on the front of the thermostat.
Error Messages:
Your thermostat can give you four error indications:
1. “heater error”: This will occur if the heater is not correctly connected to the thermostat
2. “overload”: This will occur if more than 3.6kW (16 Amps) has been connected to the thermostat
3. “er1”: This will occur if no oor sensor is detected
4. “er2”: This will occur if the oor sensor has a short circuit
Contact:
UK
Warmup Plc
702 Tudor Estate
Abbey Road
London
NW10 7UW
T: 0845 345 2288
International: + 44 208 453 6868
F: 0845 345 2299
E-mail: [email protected]
Website: www.warmup.co.uk
USA
Warmup, Inc
52 Federal Road
Unit 1F
Danbury CT 06810
Toll Free Tel: [phone]
Toll Free Tel: 888-warmfeet
Toll Free Fax: [phone]
Local Tel: [phone]
International: +1 203-...
Local Fax: [phone]
E-mail: [email protected]
Website: www.warmup.com
FRANCE
Warmup plc
16, Rue du Dr Leroy
Suite 310
72000
France
T: 805 639 905
International: [phone]
F: [phone]
E-mail: [email protected]
Website: www.warmupfrance.fr
GERMANY
Warmup Heizsysteme
Dungstup 18
27793 Wildeshausen
T: [phone]
F: [phone]
E-mail: [email protected]
Website: www.warmupdeutschland.
de
PORTUGAL
Warmup Portugal
Rua Fundo de Vila, Loja R
3700-120 S. J. da Madeira
T: 800 812 080 (Portugal Only)
F: 800 812 063 (Portugal Only)
E-mail: [email protected]
Website: www.warmup.pt
SPAIN
Warmup sl
Francisco de Rojas, 2
28010 Madrid
España
>
T: 800 099 988 (Spain Only)
F: 800 099 989 (Spain Only)
E-mail: españ[email protected]
Website: www.warmup.es
Disposal
Appliances with this symbol must not be disposed of with general waste. Seek guidance
from you local government or the retailer where you purchased the product.

Installer’s Notes:

Check out our full range of Heating Products
Central Heating Controls
Honeywell Heating Controls
Danfoss Heating Controls
Radiator Valves
Fernox
Sentinel
Magnaclean
Warmup underfloor heating
Water Heaters
Hand Dryers