Warmup TH115-AF-GA User manual

Owner’s Guide
TH115-AF-GA / TH115-AF-GB
Programmable thermostat
400-115-051-B

ENGLISH
TH115-AF-GA / TH115-AF-GB
Overview
Before you start..................................................2
About your thermostat........................................3
Controls..............................................................4
Display ...............................................................5
Installation
Installing the thermostat .....................................6
Wiring diagrams .................................................7
Connecting the floor sensor / remote control .....8
Setting the configuration switches......................9
Setup
Time and day....................................................10
Daylight Saving Time .......................................11
Floor temperature limits....................................12
Preset temperatures.........................................13
Default schedule ..............................................14
Modifying the schedule ....................................15
Operation
Running the schedule (Automatic mode) .........16
Temporary override of schedule.......................16
Permanent override (Manual mode) ...............17
Before going on vacation (Vacation mode) ......17
Ground fault protection (GFCI).........................18
Appendices
Error messages................................................20
Technical specifications....................................21
Customer assistance........................................22
Warranty...........................................................23
Table of contents
400-115-051-B (Honeywell TH115-AF-GA_GB) 5 x 3.125 EFS.book Page 1 Monday, April 12, 2010 3:10 PM

Owner’s Guide
2
ENGLISH
Read the entire document
CAUTION:
• Installation must be carried out by a certified electrician and must comply with national and
local electrical codes.
• Use this thermostat for resistive loads only.
• Do NOT install the thermostat in an area where it can be exposed to water or rain.
• To prevent severe shock or electrocution, always turn the power Off at the service panel
before working with wiring.
• Install the thermostat onto an electrical box.
• Use special CO/ALR solderless connectors if you connect the thermostat to aluminum wires.
• Keep the thermostat's top and bottom air vents (openings) clean and unobstructed at all
times.
Before you start
400-115-051-B (Honeywell TH115-AF-GA_GB) 5 x 3.125 EFS.book Page 2 Monday, April 12, 2010 3:10 PM

TH115-AF-GA / TH115-AF-GB
3
ENGLISH
The TH115 programmable thermostat has three temperature control modes:
See page 9 on how to change the temperature control mode setting.
Supplied Parts
• One (1) thermostat
• Two (2) mounting screws
• Four (4) solderless connectors for copper wires
• One (1) floor sensor
• One (1) flat-tip screwdriver
About your thermostat
A mode: controls the ambient air temperature
F mode: controls the floor temperature using an external temperature sensor
AF mode: controls the ambient air temperature
maintains the floor temperature within desired limits using an external temperature
sensor
400-115-051-B (Honeywell TH115-AF-GA_GB) 5 x 3.125 EFS.book Page 3 Monday, April 12, 2010 3:10 PM

Owner’s Guide
4
ENGLISH
Controls
On/Off switch*
Day button
Temperature adjustment buttons**
Program button
Mode selection / program exit
Preset temperature buttons
(see page 13)
Backlight button**
Program clear button
Hour button
Minutes button
*
Place at Off to cut power to the heater (e.g., in the summer). This will not affect the time and temperature settings.
** When the backlight button or either of the buttons is pressed, the display illuminates for 12 seconds.
TEST light/button for ground
fault protection (see page 18)
400-115-051-B (Honeywell TH115-AF-GA_GB) 5 x 3.125 EFS.book Page 4 Monday, April 12, 2010 3:10 PM

TH115-AF-GA / TH115-AF-GB
5
ENGLISH
Display
Temperature*
Operation mode icon
(see pages 16 & 17)
Period (see page 14)
Time
Number of flames varies
according to heating intensity
Preset temperature icon (see page 13)
Appears when the setpoint
temperature is displayed*
Temperature control mode
(see pages 3 & 9)
Ground fault indicator (see page 18)
Day
* The thermostat normally displays the actual (measured) temperature. To view the setpoint temperature, briefly press
either of the buttons. The setpoint will appear for 5 seconds. To change the setpoint temperature, press one of the
buttons until the desired temperature is displayed. To scroll faster, press and hold the button.
400-115-051-B (Honeywell TH115-AF-GA_GB) 5 x 3.125 EFS.book Page 5 Monday, April 12, 2010 3:10 PM

Owner’s Guide
6
ENGLISH
nTurn the heating system off at the main electrical panel.
oLoosen the bottom screw and remove the thermostat faceplate from its
wallplate. (The screw cannot be completely removed.)
pConnect the thermostat to the load and to the power supply (see page 7).
qConnect the floor sensor (see page 8).
rIf you wish to connect a remote control device, see page 8.
sInstall the wallplate to the electrical box using the provided screws.
tSet the configuration switches on the back of the faceplate (see page 9).
uInstall the faceplate back on the wall plate and tighten the screw.
vApply power to the heating system.
wTest the ground fault protection (see page 19).
Installing the thermostat
Wallplate
Faceplate
400-115-051-B (Honeywell TH115-AF-GA_GB) 5 x 3.125 EFS.book Page 6 Monday, April 12, 2010 3:10 PM

TH115-AF-GA / TH115-AF-GB
7
ENGLISH
NOTE: Connect the wires using the provided solderless connectors for copper wires.
Wiring diagram
White
120 V
Load
Power
supply
Red
Black
Red
Red
Black
Black
Red
Black
240 V
Load
Power
supply
Red
Black
Red
Black
Black
Black
White
400-115-051-B (Honeywell TH115-AF-GA_GB) 5 x 3.125 EFS.book Page 7 Monday, April 12, 2010 3:10 PM

Owner’s Guide
8
ENGLISH
nInsert the floor sensor cable through one of the two
openings on the wallplate and connect the sensor
wires to terminals 1 and 2 (no polarity).
• The sensor cable must not come in contact with the
electrical wires and must be routed outside the
electrical box and follow the wall down to the floor.
• Position the sensor cable such that it does not
come in contact with the floor heating wires. The
sensor must be centered between two floor heating
wires for best temperature control.
• Do NOT staple the sensor head (the plastic end) to
the floor. Doing so might damage the sensor. Any
damage might not be noticeable during testing but
can become apparent several days later.
oIf you wish to connect a remote control device (see
page 17), insert the wires (use 18- to 22-gauge flexible
wires) through one of the two openings on the wallplate
and connect them to terminals 2 and 3 (no polarity).
Connecting the floor sensor / remote control
Floor
temperature
sensor
Remote control device
400-115-051-B (Honeywell TH115-AF-GA_GB) 5 x 3.125 EFS.book Page 8 Monday, April 12, 2010 3:10 PM

TH115-AF-GA / TH115-AF-GB
9
ENGLISH
Configuration switches are on the back of the faceplate.
Set the configuration switches
# Configurations Up Down
1 Display format °F / 12 h °C / 24 h
2Early Start1
1. Early Start is used in Automatic mode only. When Early Start is enabled (on), the thermostat determines when to start
heating so the Comfort temperature is attained at the beginning of periods 1 and 3. When Early Start is disabled (off),
heating starts only at the beginning of periods 1 and 3; thus there is a delay before the Comfort temperature is
reached.
Enable Disable
3Temperature control mode2
2. See page 3. To select the F Mode, place the switch in the F position. To select the AF Mode, place the switch in the AF
position and ensure that the temperature sensor is connected to the thermostat. To select the A Mode, place the switch in
the AF position and ensure that the remote temperature sensor is NOT connected to the thermostat.
FAF
400-115-051-B (Honeywell TH115-AF-GA_GB) 5 x 3.125 EFS.book Page 9 Monday, April 12, 2010 3:10 PM

Owner’s Guide
10
ENGLISH
To set the clock and the day:
nPress the Hour button to set the hour.
oPress the Min button to set the minutes.
pPress the Day button to set the day.
qPress the Mode/Ret button to return the thermostat to normal display.
NOTE: The thermostat will automatically return to normal display if no button is
pressed for 60 seconds.
Time and day
400-115-051-B (Honeywell TH115-AF-GA_GB) 5 x 3.125 EFS.book Page 10 Monday, April 12, 2010 3:10 PM

TH115-AF-GA / TH115-AF-GB
11
ENGLISH
When the Daylight Saving Time function is enabled (On), the thermostat automatically switches to Daylight Saving
Time on the second Sunday of March and to normal time on the first Sunday of November.
NOTE: The Daylight Saving Time function is disabled (default setting) when the clock loses its setting.
To set the
Daylight Saving Time function and to set the date:
nPress the Day button (3 seconds) until DLS appears on the screen.
oPress either of the buttons to toggle between On (enabled) and Off (disabled).
pPress the Day button briefly. The year setting is displayed.
qPress either of the buttons to set the current year.
rPress the Day button briefly. The month setting is displayed.
sPress either of the buttons to set the current month.
tPress the Day button briefly. The date setting is displayed.
uPress either of the buttons to set the current date.
vPress the Mode/Ret button to return the thermostat to normal display.
NOTE: The thermostat will automatically return to normal display if no button is pressed for 60 seconds.
Daylight Saving Time
400-115-051-B (Honeywell TH115-AF-GA_GB) 5 x 3.125 EFS.book Page 11 Monday, April 12, 2010 3:10 PM

Owner’s Guide
12
ENGLISH
WARNING: To avoid damaging your floor, follow your floor supplier’s recommendations regarding floor tempera-
ture limits.
The minimum and maximum floor temperature limits are 5.0°C (41°F) and 28.0°C (82°F) by default.
To modify these limits, proceed as follows:
nSwitch the thermostat to Off.
oPress and hold the button.
pSwitch the thermostat back to On.
qRelease the button when the minimum temperature limit (FL:LO) appears.
rSet the minimum temperature limit using the buttons.
sPress the button to display the maximum temperature limit (FL:HI).
tSet the maximum temperature limit using the buttons.
uPress Mode/Ret to return the thermostat to normal display.
NOTE: The thermostat will automatically return to normal display if no button is pressed for 60 seconds.
Floor temperature limits (AF mode only)
400-115-051-B (Honeywell TH115-AF-GA_GB) 5 x 3.125 EFS.book Page 12 Monday, April 12, 2010 3:10 PM

TH115-AF-GA / TH115-AF-GB
13
ENGLISH
The thermostat has 3 preset temperatures. Their default settings are shown in the following table.
To use a preset temperature:
Briefly press the appropriate preset temperature button ( , or ). The preset temperature will
become the current setpoint and its icon will appear on the screen.
To modify a preset temperature:
nPress one of the buttons to display the desired temperature.
oPress and hold the appropriate preset temperature button ( , or )until its icon is displayed.
Preset temperatures
Preset temperature Intended use Icon A/AF modes F mode
Comfort When at home 21.0°C (70°F) 28.0°C (82°F)
Economy When asleep or away from home 17.0°C (63°F) 20.0°C (68°F)
Vacation During prolonged absence 10.0°C (50°F) 10.0°C (50°F)
400-115-051-B (Honeywell TH115-AF-GA_GB) 5 x 3.125 EFS.book Page 13 Monday, April 12, 2010 3:10 PM

Owner’s Guide
14
ENGLISH
The schedule consists of 4 periods per day, which represents a typical work day. The Comfort ( ) preset
temperature is automatically used in Periods 1 and 3 and the Economy ( ) preset temperature in Periods
2 and 4. You can program the thermostat to skip (cancel) the periods that do not apply to your situation. For
example, you can skip periods 2 and 3 for the weekend.
NOTE: If you wish to use only 2 periods, use the following combinations: “1 and 4” or “2 and 3”. Early Start
(see page 9) will not work with any other combinations.
You can have a different program every day; i.e., each period can start at a different time every day. The
thermostat has been programmed with the following schedule.
Default schedule
Period Description Setting MO TU WE TH FR SA SU
Wake Comfort 6:00 6:00 6:00 6:00 6:00 6:00 6:00
Leave Economy 8:30 8:30 8:30 8:30 8:30 --:-- --:--
Return Comfort 17:00 17:00 17:00 17:00 17:00 --:-- --:--
Sleep Economy 23:00 23:00 23:00 23:00 23:00 23:00 23:00
400-115-051-B (Honeywell TH115-AF-GA_GB) 5 x 3.125 EFS.book Page 14 Monday, April 12, 2010 3:10 PM

TH115-AF-GA / TH115-AF-GB
15
ENGLISH
nPress Pgm. Period 1 for Monday is displayed.
oTo program another period, press Pgm to display that period.
pTo program another day, press Day to display that day (hold for 3 seconds to
select the entire week).
qPress Hour and Min to set the period start time, or press Clear to skip
(cancel) the period (--:-- will be displayed).
rRepeat steps 2 to 4 to program another period.
sPress Mode/Ret to return the thermostat to normal display.
NOTE: The thermostat will automatically return to normal display if no button is
pressed for 60 seconds.
Modifying the schedule
400-115-051-B (Honeywell TH115-AF-GA_GB) 5 x 3.125 EFS.book Page 15 Monday, April 12, 2010 3:10 PM

Owner’s Guide
16
ENGLISH
In Automatic mode, the thermostat follows the programmed schedule (see
page 14). To place the thermostat in this mode, press Mode/Ret until is
displayed.
If you modify the setpoint temperature (by pressing the , or button) when
the thermostat is in Automatic mode, the new temperature will be used until the
beginning of the next period. flashes during the temporary override. You can
cancel the temporary override by pressing Mode/Ret.
Running the schedule (Automatic mode)
Temporary override of schedule
400-115-051-B (Honeywell TH115-AF-GA_GB) 5 x 3.125 EFS.book Page 16 Monday, April 12, 2010 3:10 PM

TH115-AF-GA / TH115-AF-GB
17
ENGLISH
To place the thermostat in Manual mode, press Mode/Ret to display on the screen. In this mode, the
thermostat does not follow the programmed schedule. Press the , or button to set the
temperature.
In this mode, the thermostat uses the vacation preset temperature (see page 13). There are two ways to
place the thermostat in Vacation mode:
Press the button on the thermostat. When the Vacation mode is activated this way, the icon
appears on the screen without flashing.
From any remote control device equipped with a dry contact. When the contact closes, the thermo-
stat is placed in Vacation mode and the icon flashes on the screen. All buttons on the thermostat
are locked. When the contact opens, the thermostat returns to the previous mode.
NOTE: When the Vacation mode is activated from a remote control device, it can only be deacti-
vated using the device.
Permanent override of schedule (Manual mode)
When you go on vacation (Vacation mode)
400-115-051-B (Honeywell TH115-AF-GA_GB) 5 x 3.125 EFS.book Page 17 Monday, April 12, 2010 3:10 PM

Owner’s Guide
18
ENGLISH
This ground fault protection thermostat is different from conventional thermostats. In the event of a ground
fault, the ground fault protection mechanism on the thermostat will trip and quickly stop the flow of
electricity to prevent serious injury.
Definition of a ground fault
Instead of following its normal safe path, electricity passes through a person’s body to reach the ground.
For example, a defective floor heating mat can cause a ground fault.
A ground fault protection thermostat does not protect against circuit overloads, short circuits, or
electrical shocks. For example, you can still receive an electrical shock if you touch bare wires while
standing on a non-conducting surface such as a wood floor.
Ground fault protection reset
When the ground fault protection mechanism trips, the TEST light is On (red). To reset the ground fault
protection, switch the thermostat to Off and back to On. The TEST light will turn off.
Ground fault protection (GFCI)
400-115-051-B (Honeywell TH115-AF-GA_GB) 5 x 3.125 EFS.book Page 18 Monday, April 12, 2010 3:10 PM

TH115-AF-GA / TH115-AF-GB
19
ENGLISH
Testing the ground fault protection
To ensure the ground fault protection is always in working order, test it once the thermostat is installed
and on a monthly basis thereafter.
nIncrease the setpoint temperature above the measured temperature in order
to activate the heating system.
oPress the TEST button.
• If the TEST light does NOT turn on, the test has failed. Cut power to the
heating system at the main electrical panel, have an electrician verify the
installation and, if necessary, replace the thermostat.
• If the TEST light turns on, continue the test.
pSwitch the thermostat to Off then back to On.
• If the TEST light turns off, the test has passed. Set the thermostat back to the desired tempera-
ture. The test is now completed.
• If the TEST light remains on, the test has failed. Continue with the rest of the procedure.
qSwitch the circuit breaker (at the service panel) of the heating system to off then back to on.
rRepeat the test. If the test fails again, cut power to the heating system at the main electrical panel,
have an electrician verify the installation and, if necessary, replace the thermostat.
TEST button/light
400-115-051-B (Honeywell TH115-AF-GA_GB) 5 x 3.125 EFS.book Page 19 Monday, April 12, 2010 3:10 PM