Wasp WDT950 User manual

Wasp WDT950Handheld Terminal (38 Keys)
User's Manual
v1.5

i
About This Manual
Preface
This manual explains how to install, operate and maintain our product.
No part of this publication may be reproduced or used in any form, or by any
electrical or mechanical means, such as photocopying, recording, or
information storage and retrieval systems, without permission in writing from
the manufacturer. The material in this manual is subject to change without
notice.
Regulatory Compliance Statements
FCC Warning Statement
This device has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference with radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference with radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver.
–Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help.
1. This transmitter must not be co-located or operating in conjunction with

ii
any other antenna or transmitter.
2. This device complies with FCC RF radiation exposure limits set forth for
an uncontrolled environment. To maintain compliance with FCC RF
exposure requirements, avoid direct contact to the transmitting antenna
during transmitting.
3. Any changes or modifications (including the antennas) made to this device
that are not expressly approved by the manufacturer may void the user’s
authority to operate the equipment.
FCC Label Statement
This device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference
that may cause undesired operation.
RF Radiation Exposure Statement
For body contact during operation, this device has been tested and meets FCC
RF exposure guidelines when used with an accessory that contains no metal
and that positions the handset a minimum of 1.0 cm from the body.
Use of other accessories may not ensure compliance with FCC RFexposure
guidelines.
Canadian Compliance Statement
This device complies with Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
(i) the device for operation in the band 5150–5250 MHz is only for indoor use
to reduce the potential for harmful interference to co-channel mobile
satellite systems;
(ii) for devices with detachable antenna(s), the maximum antenna gain
permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz
shall be such that the equipment still complies with the e.i.r.p. limit;
(iii) for devices with detachable antenna(s), the maximum antenna gain

iii
permitted for devices in the band 5725-5850 MHz shall be such that the
equipment still complies with the e.i.r.p. limits as appropriate; and
(iv) where applicable, antenna type(s), antenna models(s), and worst-case tilt
angle(s) necessary to remain compliant with the e.i.r.p. elevation mask
requirement set forth in section 6.2.2.3 shall be clearly indicated.
Canada, avis d'Industry Canada (IC)
Cet appareil est conforme avec Industrie Canada exemptes de licence RSS
standard(s).
Son fonctionnement est soumis aux deux conditions suivantes: (1) cet appareil
ne doit pas causer d'interférence et (2) cet appareil doit accepter toute
interférence, notamment les interférences qui peuvent affecter son
fonctionnement.
(i) les dispositifs fonctionnant dans la bande de 5 150 à 5 250 MHz sont
réservés uniquement pour une utilisation à l’intérieur afin de réduire les
risques de brouillage préjudiciable aux systèmes de satellites mobiles
utilisant les mêmes canaux;
(ii) ii.pour les dispositifs munis d’antennes amovibles, le gain maximal
d’antenne permis pour les dispositifs utilisant les bandes de 5 250 à 5 350
MHz et de 5 470 à 5 725 MHz doit être conforme à la limite de la p.i.r.e;
(iii) iii.pour les dispositifs munis d’antennes amovibles, le gain maximal
d’antenne permis (pour les dispositifs utilisant la bande de 5 725 à 5 850
MHz) doit être conforme à la limite de la p.i.r.e. spécifiée, selon le cas;
(iv) lorsqu’il y a lieu, les types d’antennes (s’il y en a plusieurs), les numéros
de modèle de l’antenne et les pires angles d’inclinaison nécessaires pour
rester conforme à l’exigence de la p.i.r.e. applicable au masque
d’élévation, énoncée à la section 6.2.2.3, doivent être clairement indiqués.
RF Radio Frequency Exposure Information
The radiated output power of the Wireless Device is below the Industry
Canada (IC) radio frequency exposure limits. The Wireless Device should be
used in such a manner such that the potential for human contact during normal

iv
operation is minimized.
This device has been evaluated for and shown compliant with the IC Specific
Absorption Rate (“SAR”) limits when operated in portable exposure conditions.
Informations concernant l'exposition aux fréquences
radio (RF)
La puissance de sortie émise par l’appareil de sans fil est inférieure à la limite
d'exposition aux fréquences radio d'Industry Canada (IC). Utilisez l’appareil de
sans fil de façon à minimiser les contacts humains lors du fonctionnement
normal. Ce dispositif a été évalué pour et démontré conforme à la Taux IC
d'absorption spécifique ("SAR") des limites lorsqu'il est utilisé dans des
conditions d'exposition portatifs.
European Conformity Statement
Wasp Barcode Technologies herewith declares that the Wasp product is in
compliance with the essential requirements and all other provisions of the RED
2014/53/EU directive.
The declaration of conformity is available for download here.
CE RF Exposure Compliance
For body-worn operation, this device has been tested and meets the ICNIRP
guidelines and the European Standard EN 62209-2, for use with dedicated
accessories, SAR is measured with this device at a separation of 0.5 cm to the
body, while transmitting at the highest certified output power level in all
frequency bands of this device. Use of other accessories which contain metals
may not ensure compliance with ICNIRP exposure guidelines.
CE Mark Warning

iv
RoHS Statement
This device conforms to RoHS (Restriction of Hazardous Substances) European
Union regulations that set maximum concentration limits on hazardous materials
used in electrical and electronic equipment.
Waste electrical and electronic equipment (WEEE)
Wasp has set up a policy and process to meet the
2012/19/EU concerning electronic waste disposal.
For more detailed information of the electronic waste
disposal of the products you have purchased from Wasp
directly or via Wasp’s resellers, you shall either contact
your local supplier or visit here.

v
Taiwan NCC Warning Statement
低功率電波輻射性電機管理辦法
第十二條：經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者
均不得擅自變更頻率、加大功率或變更原設計之特性及功能。
第十四條：低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有
干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。
前項合法通信，指依電信法規定作業之無線電通信。
低功率射頻電機需忍受合法通信或工業、科學及醫療用電波輻射性電機設備
之干擾。
SAR標準值2.0W/KG, 送測產品實測值為: 0.395 (W/KG)
注意事項:
1. 使用過度恐傷害視力。
2. 使用30分鐘請休息10分鐘；未滿2歲幼兒不看螢幕，2歲以上每天看螢幕不要超
過
1小時。

vi
3. 減少電磁波影響，請妥適使用。
4. 因應各地區/國家開放頻道不同，請依據當地主管機關與電信業者實際公告資訊
為主，如服務細則有所變更，請自行洽詢電信業者，恕不另通知。
5. 無線資訊傳輸設備避免影響附近雷達系統之操作
Note:
Within the 5.25-5.35 GHz band, U-NII devices will be restricted to indoor operations to reduce any
potential for harmful interference to co-channel MSS operations.

vii
Laser Information
The Wasp product is certified in the U.S. to conform to the requirements of
DHHS/CDRH 21CFR Subchapter J and to the requirements of IEC 60825-1.
Class II and Class 2 products are not considered to be hazardous. The Wasp
product contains internally a Visible Laser Diode (VLD) whose emissions do
not exceed the maximum limits as set forth in the above regulations. The
scanner is designed so that there is no human access to harmful laser light
during normal operation, user maintenance or prescribed service operations.
The laser safety warning label required by the DHHS/IEC for the Wasp
product’s optional laser scanner module is located on the memory
compartment cover, on the back of the unit.
* Laser information only applies to the products with laser components.
CAUTION! Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous laser
light. Use of optical instruments with the scanner, including
binoculars, microscopes, and magnifying glasses, will increase
eye damage. This does notinclude eyeglasses worn by the
user.
LED Information
The Wasp product contains LED indicator(s) or LED ring whose luminance is
not harmful to human eyes during normal operation, user maintenance or
prescribed service operations.
*LED information only applies to the products with LED components.

x
Battery Notice
1. To guarantee optimal performance, itisrecommended that rechargeable
batteries be replaced every year,orafter 500 charging cycles are
completed. Itisnormal for the battery to balloon or expand after oneyear
or 500 cycles. Although it does not cause damage, it cannot be used again
and must be disposed of according to the location's safe battery disposal
procedures.
2. If abattery performance decreases more than 20%,the battery isat the
end of its life cycle. Stop use and ensure the battery isdisposed of
properly.
3. The length of time that a battery lasts depends on the battery type and
how the device is used. Conserve the battery life by doing the following:
Avoid fully uncharging the battery because this places additional
strain on it. Several partial uncharges with frequent charges are better
than a fully uncharged battery.Charging a partially charged battery
does not cause harm to the unit.
DO NOT leave the battery pack or the device in a hot condition
such as inacar with the doors closed on a hot day orsimilar
environment, and/or underdirect sunlight for anextended period
of time. High-temperature conditionsmight cause battery
damaged for further safe usage. Keep the device with the battery
within acceptable operating temperatures (please refer to the
“specification” section for further details).
Toguarantee optimal battery performance, wegenerally
recommend you replace your rechargeable batteries every two
years, orafter 500charging cycles. Failure to comply with the
above warnings and using the battery neglectfully may lead to critical
consequences.
Do not leave the battery uncharged and unused for an extended

xi
period of time, the battery will wear out and the longevity ofthe
battery will be at least half ofone with frequent charges.
4. Protect battery life by not over or under charging the battery.
5. Please do not leave battery unused for a long time without charging it.
Despite Wasp’s safety precautions, the battery packmay begin to change
shape. Ifso, stop using it immediately.Please check to see if you are
using a proper power adapter to charge the battery or contact your service
provider for service.
6. If you cannot charge the battery after ithas been idle for an extended
period of time and itbegins toheat up, please do not try to charge it. It
may not be functional anymore.
7. Please only use the original battery from Wasp.Using a third-party battery
can damage our products. Please note that when such damage occurs, it
is not covered by Wasp’s warranty policy.
CAUTION! RISK OF EXPLOSION IF BATTERY IS
REPLACED INCORRECTLY.
DISPOSE OF USED BATTERIES ACCORDING
TO THE INSTRUCTIONS.
如果更換不正確之電池行事會有爆炸的風險
請依製造商說明書處理用過之電池
如果更换不正确之电池行事会有爆炸的风险
请依制造商说明书处理用过之电池
Battery charge notice
It is important to consider temperature when the battery pack is charging.
Charging is most efficient at normal room temperature or in a slightly cooler
environment. It is essential that batteries are charged within the stated range of
0°C to 40°C. Charging batteries outside of the specified range could damage
the batteries and shorten their life cycle.
CAUTION! Do not charge batteries at a temperature lower than 0°C. This will
make the batteries unstable and dangerous. Please use a battery
temperature detecting device for a charger to ensure a safe
charging temperature range.

xii
CAUTION! To ensure the unit worksproperly,please keep allconnectors
away from contaminants such as dust, grease, mud,
and water.Negligence may cause the unit to lose
communication, short circuit, overheat, and so on.
CAUTION! If the connector isdamaged, please ensure the connector is
fully repaired before use toavoid causing a short circuit.
Storage and safety notice
Although charged batteries may be left unused for several months, their
capacity may be depleted due to buildup of internal resistance. If this happens,
they will require recharging prior to use. Batteries may be stored at
temperatures between -20°C to 60°C, however they may deplete more rapidly
at higher temperatures. It is recommended to store batteries at room
temperature.
* The message above only applies to the usage of the removable batteries.
For the products with non-removable batteries / without batteries, please refer to
the specification of each product.
Product Operation and Storage Notice
The Wasp product has applicable operation and storage temperature
conditions. Please follow the limitation of suggested temperature conditions to
avoid failure, damage or malfunction.
*For applicable temperature conditions, please refer to the specification of each
product.

x
Adapter Notice
1. Please do not leave the power adapter in the socket when it is not
connected to your Wasp product for charging.
2. Please remove the power adapter when the battery is fully recharged.
3. The bundled power adapter that comes with your Wasp product is not
meant to be used outdoors. An adapter exposed to water or rain, or a very
humid environment can cause damage to both the adapter and the
product.
4. Please only use the bundled power adapter or same specification of
adapter to charge your Wasp product. Using the wrong power adapter can
damage your Wasp product.
* The message above only applies to the product connected to the adapter.
For the products without using the adapters, please refer to the specification of
each product.

xi
Hearing Damage Warning
To prevent possible hearing damage, do not listen at high volume levels for long periods.

xii
Technical Support
Wasp’s professional support team is available to quickly answer questions or
assist with technical-related issues. Should an equipment problem occur,
please contact Wasp technical service.
For more information, visit https://support.waspbarcode.com.

xiii
Warranty Policy
The following items covered under the Wasp Limited Warranty are free from
defects during normal use:
The warranty period is varied from each country. Please consult with your
supplier or Wasp local office for actual length of warranty period to your
purchased product.
Warranty becomes void if equipment is modified, improperly installed or used,
damaged by accident or neglect, or if any parts are improperly installed or
replaced by the user.

xiv
Table of Contents
Preface............................................................................................................. i
Regulatory Compliance Statements.............................................................. i
Laser Information ....................................................................................... vii
LED Information ......................................................................................... vii
Battery Notice............................................................................................... x
Adapter Notice.............................................................................................. x
Hearing Damage Warning ........................................................................... xi
Worldwide Support ..................................................................................... xii
Warranty Policy ..........................................................................................xiii
Chapter 1 - Overview................................................................................1
1.1 Package .................................................................................................1
1.2 Product Detail.........................................................................................2
1.3 Specifications .........................................................................................3
1.4 Getting Started .......................................................................................6
1.5 Keypad Definition .................................................................................18
Chapter 2 – Installation & Operation ................................................24
2.1 Barcode Setting....................................................................................24
2.2 HF Setting ............................................................................................28
2.3 WWAN Setting......................................................................................30
2.4 WLAN Setting....................................................................................... 32
2.6 PAN Setting ..........................................................................................37
2.7 GPS Setting..........................................................................................38
2.8 PC Setting ............................................................................................39
2.9 Camera Setting ....................................................................................40
2.10 Performing a Hardware Reset ............................................................44
2.11 Performing Factory data reset ............................................................45
2.12 KeyRemap..........................................................................................47
2.13 Split Screen........................................................................................50
2.14 Network Time Protocol (NTP) Server .................................................52
2.15 Battery Swap ......................................................................................54

xv
Chapter 3 – Introduction to Applications.........................................55
3.1 USS (scan service)...............................................................................55
3.2 File Manager ........................................................................................59
3.3 Software Update...................................................................................60
3.4 StageGO ..............................................................................................61
3.5 MoboLink..............................................................................................63

1
Wasp WDT950 (38 keys) User’s Manual
Chapter 1- Overview
1.1 Package
Pleasemake sure the following itemsarein the WDT950box.
If something is missing or damaged, please contact your Wasp representative.
The basic package contents
WDT950
Battery
Hand Strap
Quick Start Guide
Regulatory Compliance Statements
Optional accessories
Terminal Power Adapter
Cradle + Cradle Adapter
1-slot Terminal & Battery Charging Cradle
1-slot Ethernet & Battery Cradle
1-slot USB & Battery Cradle
Glass Screen Protector
USB Type C Cable

2
Wasp WDT950 (38 keys) User’s Manual
1.2 Product Detail
1
Scanner Window
6
Receiver
2 13m Camera & LED
Flashlight
7 Pogo pin
3
LED Indicator
8
USB Type C Port
4
Scanner Trigger Key 9 Battery Release Latch
5
Keypad
10
Battery Cover
①
②
⑥
③
③
④
④
Power Key
⑤
⑦
⑦
⑧
⑨
⑩
On
Off