Watec WAT-600CX Installation manual

Color CCD Camera
WAT-600CX
Operation Manual
This Operation Manual covers safety, camera functions, installation and the
correct operating procedure for the WAT-600CX First, we ask you to read
this Operation Manual thoroughly, then install and operate the WAT-600CX
as advised In addition, for future reference, we also advise safekeeping of
this manual
Please contact the distributor or dealer from which the WAT-600CX was
purchased, if you do not understand the installation, operation or safety
instructions laid out in this manual Not understanding the contents of the
Operation Manual sufficiently may cause damage to the camera
Guide to the Safety Symbols
The definitions of the symbols used in this operation manual are:
When you do not adhere to or take notice of the “Danger” sign,
it may lead to a serious accident such as death or injury caused
by fire or electric shock
When you do not adhere to or take notice of the “Warning” sign,
it may cause severe damage such as a physical injury
When you do not adhere to or take notice of the “Caution” sign,
it may incur injury and cause damage to peripheral objects in
the immediate surroundings
Cautions for Safety
The WAT-600CX is designed to be used safely; however, it may lead to a
physical accident caused by fire and electric shock if not used correctly
Therefore, please keep and read the “Cautions for safety” below for
protection against accidents
• Do not disassemble and/or modify the WAT-600C .
• Do not operate the WAT-600C with wet hands.
• Use only the AD-156 with the WAT- 600C set .
• Do not use the WAT- 600C under unusual environmental
conditions.
The WAT-600CX is designed and approved for indoor use only
The WAT-600CX is not water-resistant, dustproof, or
explosion proof If the location of the camera is outdoors or in
an outdoor like environment, we recommend that you use an
outdoor camera housing
• Protect the WAT-600C from condensation.
Keep the WAT-600CX dry at all times during storage and
operation
• Should the camera not work properly, switch off the power
immediately Then check the camera according to the
“Problems and Trouble shooting” section
• Avoid the striking of hard objects or dropping the WAT-
600C .
The WAT-600CX uses high quality electrical parts and
precision components
• The WAT-400R must be used with the WAT-600C .
Only the WAT-400RX should be attached to the WAT-600CX
BNC terminal Connecting a monitor directly to this terminal
will not provide a picture
• Do not install the WAT-600C in a position subject to
direct sunlight.
Sunlight shinning directly onto the WAT-600CX lens can
cause damage to the CCD
• Select a stable place for installation of the WAT-600C .
Use a support of durable strength around an installation
position on a ceiling or wall when a camera stand or tripod is
used
• Do not move the WAT-600C with the cables connected.
Before moving the WAT-600CX, always remove the cable(s)
from the rear of the camera first
• Avoid using the WAT-600C near any strong
electromagnetic field.
After installing into main equipment, if the WAT-600CX is
exposed to electromagnetic waves causing the monitored
image to become distorted, we recommend the camera be
shielded by appropriate protective casing
Problems and Trouble Shooting
If any of the following problems occur when using the WAT-600C ,
• An optimal picture cannot be obtained, after checking that all the cables
and connections are correctly in place
• Smoke or any unusual odor emerges from the WAT-600CX
• An object becomes embedded or a quantity of liquid seeps into the
camera housing
• More than the recommended voltage or/and amperage has been applied
to the WAT-600CX by mistake
• Anything unusual occurring to any equipment connected to the WAT-
600CX
disconnect the camera immediately according to the following
procedures:
①Switch off the main power supply to the camera
②Remove the cable(s) connected to the WAT-600CX
③Contact the distributor or dealer from which the WAT-600CX was
purchased
About EMC
The WAT-600CX is in conformity with EMC test standards carried out by
authorized organizations in Japan
NTSC FCC Part15 class B
P A L EN61000-6-3/EN50130-4
Do not modify the WAT-600CX A modified camera may not
conform to EMC test standards
Contents
Using the contents figures below, check to make sure all parts are present
before use
Lens WAT- 600CX DC Plug AC Adaptor (AD-156)
Mount Cap
Description of Parts
①CCD FRONT FACE
・
・・
・The light receiving face of the CCD camera
(Dirt, water or oil deposits on the CCD will cause an unclear picture on
the monitor Attach the lens cap to protect the lens and the CCD from
contamination and damage )
②LENS MOUNT
・
・・
・Mount for the lens (CS-mount)
③IRIS LEVEL VOLUME
・
・・
・By controlling the volume, the iris level of the DC iris lens can be adjusted
④FOCUSING ADJUSTMENT SCREWS
・
・・
・There are 3 hex adjustment screws each placed at intervals of 120゜for
fine focusing of the lens
⑤AUTO-IRIS SOCKET
・
・・
・This socket is for the video/DC auto-iris lens cable connector
(Video/DC: Auto selected by the camera)
⑥TRIPOD MOUNTING SCREW HOLES
・
・・
・Mounting holes for stands The size of these threads are 1/4”, 20 threads,
4 5±0 2mm, which is the same as any standard camera tripod (U1/4”)
⑦AE MODE CONTROL
・
・・
・The switch for the shutter speed mode control according to the object
being monitored
⑧TEST VIDEO OUT (RCA)
・
・・
・The video out terminal for test monitoring at the camera location
⑨VIDEO OUT/POWER IN (BNC)
・
・・
・The terminal for composite video signal output and power input
⑩WHITE BLEMISH CORRECTION
・
・・
・The button for correction of white blemish
⑪FUNCTION SWITCHES
・
・・
・Functional switches for setting AGC, gamma control, BLC (Back light
compensation), video level, and white balance modes
⑫PUSH-LOCK WHITE BALANCE BUTTON
・
・・
・The button for manual setting of the white balance if the white balance
mode is set to PWB
Auto-iris Lens
Before connecting the auto-iris lens, please make sure that the pin
configuration is correct by confirming with the following table If the
configuration of your iris connector is different from the following, the plug
and pins will need to be rewired
Pin No
EIAJ Video
Auto-iris Lens
Arrangement
EIAJ DC
Auto-iris Lens
Arrangement
① Power Control －
② Not used Control ＋
③ Iris signals Drive ＋
④ Common (GND) Drive －
・Maximum cable length for operation of the WAT-600CX depends on which
lens is used For example, 100m is the maximum cable length for the
WAT-600CX when an auto-iris lens with a current consumption of 50mA
is applied
Wiring Diagram
The following diagram is the basic connection of the WAT-600CX, WAT-
400RX, AD-156 and monitor
Set-up and Operation
1) Ensure that the power to the WAT-600CX and the peripheral equipment
is turned off before making any connections
2) Remove the lens mount cap from the WAT-600CX and attach the
CS-mount lens Use the optional C-mount adaptor (30CMA-R) when a
C-mount lens is used
3) Connect the iris control cable to ⑤AUTO-IRIS SOCKET on the WAT-
600CX when an auto-iris lens is being used
4) Connect ⑨VIDEO OUT/POWER IN of the WAT-600CX to the
“CAMERA” connection terminal of the WAT-400RX Use a coaxial cable
with 75Ω impedance, such as an RG-58/U The maximum cable length
for the WAT-600CX attached to a manual iris lens is 150m using an
RG-58/U cable
5) Connect the VIDEO OUT (MONITOR) on the WAT-400RX to the video
signal input terminal of a monitor using a coaxial cable with 75Ω
impedance, such as an RG-58/U
※ Select a monitor with the same television system as the WAT-600CX:
NTSC or PAL A monitor with more than 600TV lines is recommended
※ Do not connect the WAT-600CX or the WAT-400RX with any monitor
using a video in/power out single transmission terminal The
WAT-600CX and the WAT-400RX are not designed for use with this
type of equipment and receiving power through a monitor will cause
damage to both the WAT-600CX and the WAT-400RX
6) Connect the attached AC adaptor (AD-156) to the POWER IN connector
of the WAT-400RX
7) When a monitor test of the camera angle of view and functional settings
at the location is required, connect ⑧TEST VIDEO OUT of the
WAT-600CX to the monitor using a coaxial cable with 75Ω impedance,
such as an RG-58/U
8) Turn on the power to the WAT-600CX, monitor and all the other allied
equipment When a picture cannot be obtained on the monitor, check
and follow the procedure mentioned in the “Problems and Trouble
Shooting” section
9) After following the procedure below and the picture is still out of focus,
open the iris fully and loosen ④FOCUSING ADJUSTMENT SCREWS
with the hex wrench and move the lens forwards until a clear picture is
obtained
Manual Lens Adjust the focus and iris to the best position
on the lens
Video Auto-iris Lens Adjust the focus on the lens
DC Auto-iris Lens Adjust the iris level on the camera, then
adjust the focus on the lens See below
Iris Level Adjustment (for DC auto-iris lenses only)
Adjust ③IRIS LEVEL VOLUME placed on the side
of the unit until an acceptable light level is attained
No change will occur if a video iris lens or manual
iris lens is fitted
10) Select any required shutter speed mode by the ⑦AE MODE
CONTROL (Factory default: EI)
AE Mode Effect
OFF Fixes the shutter speed to NTSC1/60, PAL1/50
FL
Reduces the flickering phenomena occurring on the
monitor screen caused by fluorescent or mercury
lamps
1/1000 Fixes the shutter speed to 1/1000
EI
(Flicker suppress)
For electronic iris reducing the flickering phenomena
occurring on the monitor screen caused by
fluorescent or mercury lamps
※ In EI mode, intense light may leave a trail on the screen longitude
This smearing is a natural phenomenon and is not due to equipment
failure or fault
Danger
Danger
Danger
Warning
LEVEL
CLOSED
OPEN
Caution
①
②
③
④
Warning
Caution
Hex
Wrench
Receiver
(WAT- 400RX)

1503Z00-Y2000001
11) Set the ⑪FUNCTION SWITCHES according
to requirements
Switch Setting Effective Condition Factory
default
ON When sensitivity is more important than
the SN ratio
1.
AGC
OFF
When SN ratio is more important than
sensitivity, or when a stable lighting
condition is present
ON
【HI】
When sensitivity is more important than
SN ratio
2.
AGC
OFF
【LO】
When SN ratio is more important than
sensitivity, in addition AGC is also
required
ON
When the picture of the monitored
object is silhouetted due to strong
lighting from above or behind
3.
BLC
※
OFF When the illumination differences
between a monitored object is narrow
ON Applicable to a general surveillance
monitoring system
4.
Gamma
Correction
OFF When gamma correction is not
required for image processing
ON
【100】
When dark areas on an object with
contrasting light and dark area are
monitored
5.
Video
Level
OFF
【75】
When the standard video output level
is required
ON
【ATW】
Automatically follows and adjusts to the
changing color temperature of the
illumination
6.
White
Balance
OFF
【PWB】
Adjusted with ⑫PUSH-LOCK WHITE
BALANCE BUTTON according to the
color temperature of the environment
and fixes the resultant color
temperature at that setting
※
When BLC is used and ⑦AE MODE CONTROL setting is set to either
OFF, FL, or 1/1000, please apply an auto iris lens
12) Correct white blemish(s) by ⑩WHITE BLEMISH CORRECTION
BUTTON The WAT-600CX is manufactured using high-grade CCD
devices that are selected by tough standards by the manufacturer
However, it is impossible to prevent the white blemishes from occurring
after shipment because the white blemish phenomena can be caused
by cosmic rays The WAT-600CX has a white blemish correction circuit
to help control the white blemish phenomena Correct according to the
following procedures, if white blemishes are present
[PROCEDURE]
1 Completely cover the lens to prevent light entering
2 Set to AGC ON by ⑪FUNCTION SWITCHES
3 Set the white balance mode to PWB by ⑪FUNCTION SWITCHES
4 Press the ⑩WHITE BLEMISH CORRECTION BUTTON using a
fine stick
5 After 5 seconds, the white blemishes are automatically detected, and
then recorded to the camera
※ Make sure that the lens is completely shielded from light before
correction of the white blemishes If the lens is not covered properly
and light can enter into the lens on to the CCD face, the correction of
the white blemish may not be detected correctly
※ Make sure that “PWB” setting is selected by ⑪FUNCTION
SWITCHES If ATW position is selected; the data cannot be saved to
the camera
Options
To purchase these options, please contact the distributor or dealer from
which you purchased the WAT-600CX
Specifications
Contact information
Watec Co., Ltd.
Watec Co., Ltd.Watec Co., Ltd.
Watec Co., Ltd.
Add : 254-2 Nihonkoku, Daihoji, Tsuruoka- Shi,
Yamagata-Ken, 997-0017 Japan
TEL: [phone] FAX: [phone]
Email: info-o@watec co jp
URL: http://www watec net
Model WAT-600C (NTSC)
WAT-600C (PAL)
Pick-up Element 1/3 inch interline transfer CCD image sensor
Number of Total Pixels
811(H)×508(V) 795(H)×596(V)
Number of
Effective Pixels 768(H)×494(V) 752(H)×582(V)
Unit Cell Size 6 35μm(H)×7 4μm(V)
6 5μm(H)×6 25μm(V)
Imaging System Ye, Cy, Mg, and G complementary
color mosaic filters on chip
Sync System Internal
Scanning System 2:1 interlace
Video Outputs
･ BNC: VIDEO OUT/POWER IN
･ RCA: Composite video, 1 0 V(p-p) 75Ω (Unbalanced)
Resolution (H) More than 540TVL (Center)
Minimum Illumination
0 02 lx F1 2
S/N More than 50dB (AGC=0dB, γ= 1 0)
OFF 1/60 sec 1/50 sec
FL 1/100 sec 1/120 sec
ES 1/1000 sec
AE
Mode
EI
(Flicker suppress)
1/60-1/100000 sec 1/50-1/100000 sec
White Balance ATW (Color rolling less), PWB
ON HI: 0-38dB / LO: 0-32dB
AGC
OFF 0dB
Gamma Characteristics
γ≒0 45(ON) / γ=1 0(OFF)
Video level 100IRE / 75IRE
Lens iris Video / DC (EIAJ arrangement, Auto-select)
Back Light
Compensation ON / OFF
White blemish correction Up to 32 dots
Power Supply DC+15V
Power Consumption
3 3W (220mA)
Operating Temperature
-10 - +50℃ (Without condensation)
Operating Humidity Less than 95% RH
Storage Temperature
-30 - +70℃ (Without condensation)
Storage Humidity Less than 95% RH
Lens Mount CS-mount (Back focus adjustable)
Size 44(W)×44(H)×64(D) mm
Max cable length
※
150m (RG-58/U)
Weight Approx 140g
Mini Stand (MS50)
A convenient stand for the WAT
-600CX
With this stand, the camera can be
adjusted to any desired angle
※
The normal operation of the WAT-600CX with a maximum cable length
(150m) is only ensured when a manual iris lens is used
• Design and specifications are subject to change without notice
• Watec is not responsible for any inconvenience or the attendant
damages
to the video and monitoring recording equipment caused by misuse, mis-
operation or improper wiring of our equipment
• If for any reason the WAT-600CX does not work properly, or if you have
any questions regarding installation or operation, please contact the
distributor or dealer from which it was purchased
Bracket (B003)
This bracket is effective for a stable
installation of the WAT-600CX
C
-
mount Adaptor (34CMA
-
R)
This lens mount adaptor is used to
convert a CS-mount to a C-mount