Waterpik Technologies WP-100 User manual

QUICK START GUIDE
3 4
5
REGISTER YOUR
PRODUCT
ONLINE NOW!
Receive up to
$44
in savings.
www.waterpik.com/register
Fill
Select and Insert Tip:
Insert
NO
Gap
6 7
Replace
1 2
ON
High
Low
PAUSE Remove Tip
Eject
Button
Model WP-100
Remove the reservoir from
base and fill with lukewarm
water.
Replace the reservoir onto
the base, PRESSING DOWN
FIRMLY to ensure full seating.
Lean over sink and close lips
enough to prevent splashing,
while still allowing water to
flow from mouth into the sink.
Turn unit ON.
For first time
users, adjust
pressure control
to lowest position.
Gradually increase
pressure as you prefer.
Always place tip in mouth
before turning unit on.
Prior to Very First Use of Unit, Prime Unit:
Set pressure control dial on base to high, point
the handle and tip into sink. Turn unit ON until
water flows from the handle, turn unit OFF.
You can temporarily stop
water flow by pressing the
pause button on the
handle.
continued on back
Push the tip eject button on the
handle. The control knob will rise,
releasing the tip. Remove the tip.
Caution: Do not press tip eject
button while unit is running.
Aim the tip just above the gumline
at a 90 degree angle.
Starting with the back teeth, follow the
gumline and pause briefly between teeth.
Continue until all areas around and
between teeth have been cleaned.
Press tip firmly into
handle. When tip is
properly inserted there
should be no gap
between control knob
and handle.
20012848-F AA
Water Pik, Inc. 1.800.525.2774 • www.waterpik.com
1730 East Prospect Road, Fort Collins, CO 80553-0001 USA ©2009 Water Pik, Inc.
Prepare the Reservoir:
Using your Waterpik® Water Flosser:
Prime Unit (First Time Use Only): Adjust Pressure and Pause Control:
Tip Removal:
BACK
5.25”
6” radius: .125”
FRONT

QUICK START GUIDE
3 4
5
REGISTER YOUR
PRODUCT
ONLINE NOW!
Receive up to
$44
in savings.
www.waterpik.com/register
Fill
Select and Insert Tip:
Insert
NO
Gap
6 7
Replace
1 2
ON
High
Low
PAUSE Remove Tip
Eject
Button
Model WP-100
Remove the reservoir from
base and fill with lukewarm
water.
Replace the reservoir onto
the base, PRESSING DOWN
FIRMLY to ensure full seating.
Lean over sink and close lips
enough to prevent splashing,
while still allowing water to
flow from mouth into the sink.
Turn unit ON.
For first time
users, adjust
pressure control
to lowest position.
Gradually increase
pressure as you prefer.
Always place tip in mouth
before turning unit on.
Prior to Very First Use of Unit, Prime Unit:
Set pressure control dial on base to high, point
the handle and tip into sink. Turn unit ON until
water flows from the handle, turn unit OFF.
You can temporarily stop
water flow by pressing the
pause button on the
handle.
continued on back
Push the tip eject button on the
handle. The control knob will rise,
releasing the tip. Remove the tip.
Caution: Do not press tip eject
button while unit is running.
Aim the tip just above the gumline
at a 90 degree angle.
Starting with the back teeth, follow the
gumline and pause briefly between teeth.
Continue until all areas around and
between teeth have been cleaned.
Press tip firmly into
handle. When tip is
properly inserted there
should be no gap
between control knob
and handle.
20012848-F AA
Water Pik, Inc. 1.800.525.2774 • www.waterpik.com
1730 East Prospect Road, Fort Collins, CO 80553-0001 USA ©2009 Water Pik, Inc.
Prepare the Reservoir:
Using your Waterpik® Water Flosser:
Prime Unit (First Time Use Only): Adjust Pressure and Pause Control:
Tip Removal:
BACK
5.25”
6” radius: .125”
FRONT