Watts Vision BT-D03 RF User manual

BT-D03 RF
Wireless digital room thermostat
WATTS Vision®System
User Guide
wattswater.eu

2BT-D03-MOI-FR-W-EN-06-19
ENGLISH ENGLISH
EN EN
TABLE OF CONTENT
General information ........................................................................................... 3
1. Presentation
................................................................................................... 4
2. Box contents ................................................................................................... 4
3. First Installation.............................................................................................. 5
4. Product description ...................................................................................... 6
4.1 LCD logo description ......................................................................................... 6
5. Mode selection................................................................................................ 7
5.1 Change temperature setting.............................................................................. 8
5.1.1 Boost/Timer mode
5.1.2 AUTO mode
5.1.3 Comfort mode
5.1.4 Reduced / ECO mode
5.1.5 Anti-freeze mode
5.1.6 OFF mode
6. Functions highlights ..................................................................................... 9
6.1 Access user parameter menu ............................................................................ 9
6.2 Reversible mode ................................................................................................10
6.3 Opened windows detection ..............................................................................10
6.4 Reset...................................................................................................................10
6.5 Keyboard locking ...............................................................................................10
6.6 PIN code .............................................................................................................11
6.7 Other informations .............................................................................................11
6.7.1 Heating and cooling indications
6.7.2 LED indication
6.7.3 Wireless communication functioning
7. User parameter description.....................................................................12
8. Installer parameter description..............................................................15
9. Troubleshooting & Solution .....................................................................17
10. Maintenance ................................................................................................18
11. Technical characteristics ........................................................................18
11.1 Dimensions & weight ........................................................................................19
12. Directives ......................................................................................................19

3
BT-D03-MOI-FR-W-EN-06-19
ENGLISH ENGLISH
EN EN
GENERAL INFORMATION
Safety warnings and operating
instructions
• This product should be installed
preferably by a qualified profes-
sional. Subject to observation of the
above terms, the manufacturer shall
assume the liability for the equip-
ment as provided by legal stipulations.
• All instructions in this Installation &
Operation manual should be observed
when working with the thermostat.
Failures due to improper installation,
improper use or poor maintenance
are voiding manufacturer liability.
• Any attempt to repair voids the respon-
sibility and the obligation to guarantee
and replacement from the manufacturer.
• Do not cover the thermostat for accu-
rate measurement of ambient tem-
perature. Therefore the sensor must
never be hidden behind thick cur-
tains, furniture, etc… Alternatively,
a remote sensor should be used.
• Batteries may explode or leak, and
cause burn injury, if recharger, disposed
of fire, mixed with a different battery
type , inserted backwards or disas-
sembled. Replace all used batteries
at the same time. Do not carry bat-
teries loose in your pocket or purse.
Do not remove the battery label. Keep
batteries away from children. If swal-
lowed, consult a physician at once.
• 2012/19/EU (WEEE directive): Products
marked with this symbol cannot be dis-
posed of as unsorted municipal waste
in the European Union. For proper recy-
cling, return this product to your local
supplier upon the purchase of equiva-
lent new equipment, or dispose of it at
designated collection points. For more
information see: www.recyclethis.info
• 2006/66/EC (battery directive): This
products contains a battery that cannot
be disposed of as unsorted municipal
waste in the European Union. See the
product documentation for specific bat-
tery information. The battery is marked
with this symbol, which may include let-
tering to indicate cadmium (Cd), lead (Pb),
or mercury (Hg). For proper recycling,
return the battery to your supplier or to
a designated collection point. For more
information see: www.recyclethis.info
Application
• The thermostat have been designed for
use in residential rooms, office spac-
es and industrial facilities. Verify that
the installation complies with exist-
ing regulations before operation to
ensure proper use of the installation.
Please refer to “Quick Installation
Guide” for thermostat installation

4BT-D03-MOI-FR-W-EN-06-19
ENGLISH ENGLISH
EN EN
1. PRESENTATION
• Connected thermostat WATTS Vision®
system compatibility.
• 3 sensitive touch buttons.
• Wireless bidirectional communication
868 MHz.
• Different temperature modes setting.
• Anti freeze function.
• Configurable Hysteresis or PWM regu-
lation.
• Pin Code & screws lock for public area.
• EEPROM non volatile memory.
• 2x1,5V AAA batteries (LR3).
• 2 parameter menus: User and Installer.
In option
External sensor with several possibilities of
regulation (Floor, remote, combined...).
2. BOX CONTENTS
WATTS Vision®thermostat
AAA type Batteries Fixing screws Lock screwsDouble side tape
Back cover and stand for table fitting
1 x
1 x 1 x 1 x1 x
1 x

5
BT-D03-MOI-FR-W-EN-06-19
ENGLISH ENGLISH
EN EN
3. FIRST INSTALLATION
See quick installation guide for installation.
Batteries installation.
• Open the cover and insert the 2 AAA
supplied batteries.
• Close the cover.
Thermostat pairing, RF wireless com-
munication initialization.
You must put your receiver or WATTS
Vision®touch screen in radio pairing
mode (refer to the device leaflet).
On the back, push 5 sec the button for
direct access to initialization menu.
Following screens are displaying:
Other method from parameter menu:
Note:
After few seconds, the thermostat and the receiver/touch screen should exit from the RF
init mode, this is the normal procedure to confirm a correct pairing.
To make the installation easier, it will be better to have the thermostat near to the receiver
or touch screen during the configuration mode.
1Press key to wake-up the thermostat 3Press key to enter in initialization
2Press 5 sec key to enter parameter
menu
Following screens are displaying:
5 sec
Going to wireless initialization menu
holding
button
holding
button
releasing
button
Initialization
starting

6BT-D03-MOI-FR-W-EN-06-19
ENGLISH ENGLISH
EN EN
4.1 LCD logo description:
1Icon showing current operating mode
of thermostat with left to right:
Boost/timer mode
Auto mode
Comfort mode
Reduced / ECO mode
Frost protection mode
Off mode
2Open window function
3RF communication
4Displaying of pilot wired order or
reduced auto mode,
order is applied to heating system
order of comfort minus 1°C
order of comfort minus 2°C
order of reduced set point or Auto
reduced mode
order of anti-freeze set point
order of stop
5Measured temperature/ tem-
perature set point / remaining time for
boost mode.
6Locked keyboard.
7 Battery level.
8Parameter menu number.
9Parameter menu.
10 Indication of heating & cooling
demand
11 Unit for power consumption.
12 Type of measured data & sensor
used for system regulation:
➤Humidity measurement & control
➤Internal temperature sensor
➤Ambient temperature sensor
➤Floor temperature sensor
➤External temperature sensor
13 User derogation or “adaptive start”
during Auto mode application
14 Temperature units or or
measurement of humidity rate.
1
23 4 6 7
8
9
10
11
12
1314
5
Minus button or
down/left button for
menu navigation.
Plus button or up/
right button for
menu navigation.
Validation of temperature set point setting or accessing
to parameter menu or displaying measured
temperature/ temperature set point.
4. PRODUCT
DESCRIPTION

7
BT-D03-MOI-FR-W-EN-06-19
ENGLISH ENGLISH
EN EN
5. MODE SELECTION
Press any key to wake-up the
thermostat and activates the back- light.
Hold key for 2 second to access to
menu for selection of mode.
Press or permits to change navigate
in different mode.If “basic navigation” is activated (menu
#03), navigation menu will be:
Menu for mode selection
Comfort, reduced, auto, stand-by,
boost or antifreeze menus
or
Automatic selection
of current mode Selection of mode Parameter menu
No user action
after 10 s
2 seconds
5 seconds

8BT-D03-MOI-FR-W-EN-06-19
ENGLISH ENGLISH
EN EN
5.1 Change temperature setting
Wake-up the thermostat by pressing any
key.
Press or , to change the tempera-
ture set point (digits starts to blink).
By pressing key, temperature set point
value is validated.
5.1.1 Boost/Timer mode
In mode boost, set point temperature is
applied during a selected time.
After this time, thermostat will return to
former mode.
You can first adjust, the desired setting
temperature with or , press key, to
validate, default value 24°C.
In a second time, you can adjust the du-
ration in hours “H” if below 24H, then in
day “d”.
5.1.2 AUTO mode
This mode is activated only when ther-
mostat is paired with a WATTS Vision®
touch screen BT-CT02.
In Auto mode, the heating system will
follow program according to the current
time and the Comfort and Reduced setting
temperatures. By pressing keys or ,
Boost/timer mode is selected, it override
the temperature set point (1h).
5.1.3 Comfort mode
In this mode, comfort temperature set
point will be followed all the time.
5.1.4 Reduced / ECO mode
In this mode, reduced temperature set
point will be followed all the time.
Note: In cooling mode, reduced mode acts
like the OFF mode (system is stopped, NC
actuators close).
5.1.5 Anti-freeze mode
Use this mode if you want to protect your
installation against freezing. (default value
7°C).
Remark: in cooling mode, Anti-freeze
mode acts like the OFF mode (installation
is stopped).
5.1.6 OFF mode
Use this mode if you need to switch off
your installation.
Be Careful: In this mode your installation
can freeze.

9
BT-D03-MOI-FR-W-EN-06-19
ENGLISH ENGLISH
EN EN
Press any key to wake-up the thermostat
and activates the backlight.
By pressing key during 5 seconds,
user can access to parameter menu.
The menu scroll is done with keys and
. Menu is selected by pressing key ,
value starts blinking. Once in the menu,
the parameter value is changed with the
keys and .
Pressing again key sets the parameter
value.
Note: Thermostat parameters are divid-
ed into two groups: user and installer
(advanced menu).
6. FUNCTIONS HIGHLIGHTS
6.1 Access user parameter menu
Comfort, reduced, auto, stand-by,
boost or antifreeze menus
Automatic return (10 seconds of keyboard inactivity)
Mode selection menu
Screensaver Navigation menu
2 seconds 5 seconds
10 seconds
without user
action 2 seconds
Parameter menu

10 BT-D03-MOI-FR-W-EN-06-19
ENGLISH ENGLISH
EN EN
6.2 Reversible mode
Reversible menu access is only pos-
sible on two conditions:
- thermostat isn’t associated to a touch
screen or 6Z master
- « reversible menu » is activated in the
user parameter menu.
Enter user parameter 08, use keys
and , to select operating mode of the
thermostat:
- Hot: Heating regulation mode
- CLd: Cooling regulation mode
- rEv: activation of reversible mode in
menu
- Aut: automatic Heat/Cool mode.
Pressing key confirms the selection
and switches to comfort mode. A user
inactivity of some seconds confirms cur-
rent selection and returns to old selected
mode.
By pressing key, temperature set point
value is validated.
6.3 Opened windows detection
Enter user parameter 07.
When activated and a detection is run-
ning, the icon will appear and blink
on the screen!; This function is done by
measuring and recording the temperature
evolution.
When an opened window is detected, the
thermostat applies to heating system anti-
freeze temperature set point. User can
restart heating system, and stops window
detection by pressing on a key.
6.4 Reset
By holding the button on the back of ther-
mostat, user can:
- Unlock pin code
- Go directly to pairing menu (5 seconds)
- Reset thermostat with user parameter
value equal to factory setting. (10 sec-
onds).
6.5 Keyboard locking
Wake-up the thermostat (lighted back-
light),
Press and hold and keys simultane-
ously.
Once locking is activated, logo appears
on the LCD screen:
5/10 Seconds

11
BT-D03-MOI-FR-W-EN-06-19
ENGLISH ENGLISH
EN EN
6.6 PIN code
To activate this function enter user param-
eter 10.
The PIN code protect the thermostat from
any change of the setting as temperature
or mode.
When user pushes a key, “PIN” will be dis-
played. If user press another time a touch,
he has to enter PIN number.
6.7 Other informations
6.7.1 Heating and cooling indications
Logos used to indicate than system
requires:
heating is ;
cooling is .
6.7.2 LED indication
When user modify set point temperature in
functioning mode, behavior information is
displayed with a LED RGB located on the
middle of validation key.
Blue < 18°C
Azure < 20°C
Green < 22°C
Yellow < 24°C
Red < 37°C
6.7.3 Wireless communication
functioning
When digital thermostat sends an RF
frame, LCD logo blinks during transmis-
sion.
RF frame is sent:
- When user press any key of the thermo-
stat.
- When user press key in Central Touch
screen to update the thermostat.
- Automatically every 3-4 minutes.

12 BT-D03-MOI-FR-W-EN-06-19
ENGLISH ENGLISH
EN EN
RF pairing activation:
Pressing the key starts
communication initialization:
Another press of key
will exit this mode.
Calibration of internal room sensor (remote):
Calibration must be done after a given order has been
operating for a day. Place the thermometer in the middle
of the room at about 1.5 m above the floor. Record the
temperature shown after 1 hour. When you enter calibration
mode for the first time, the indicator says “no”, which means
no calibration has been performed yet. Enter the reading on
your thermometer using the keys and (step of 0.1°C).
The setting is validated with key . YES appears to indicate that
calibration.
Important note: a large temperature deviation may indicate an
inappropriate installation of the thermostat. If the temperature differ-
ence is too big, this could mean your thermostat was not installed
properly e.g. in the right place.
NOTES: If user press simultaneously the keys and , sensor
calibration is reset. No is displayed.
Default value: no for offset of 0.0°C
Range values: Yes: for offset included between -3.0°C and 3.0°C.
Degree unity for displaying:
➤°C: Celsius
➤°F: Fahrenheit
Default value: °C Values: °C / °F
Buzzer activation:
“Yes”: activation of function
“no”: no activation
Default value: no Values: Yes / no
“basic navigation” mode:
“Yes”: activation of function, restrict to comfort and off mode.
“no”: no activation
Default value: no Values: Yes / no
Room temperature display:
“Yes”: remote displays measured temperature
“no”: remote displays set point temperature
Default value: Yes Values: Yes / no
7. USER PARAMETER DESCRIPTION

13
BT-D03-MOI-FR-W-EN-06-19
ENGLISH ENGLISH
EN EN
Calibration of external room sensor (remote):
This menu is only displayed if parameter rEG (#20) is set
with “Amb”. Calibration must be done after a given order
has been operating for a day. Place the thermometer in
the middle of the room at about 1.5 m above the floor.
Record the temperature shown after 1 hour. When you
enter calibration mode for the first time, the indicator says
“no”, which means no calibration has been performed yet.
Enter the reading on your thermometer using the key
and (step of 0.1°C). The setting is validated with key .
YES appears to indicate that calibration.
Important note: A large temperature deviation may indi-
cate an inappropriate installation of the thermostat. If the
temperature difference is too big, this could mean your
thermostat was not installed properly e.g. in the right place.
NOTES: If user press simultaneously the keys and ,
sensor calibration is reset. No is displayed.
Default value: no for offset of 0.0°C Range values: Yes:
for offset included between -3.0°C and 3.0°C
Open window detection:
“Yes”: activation of function
“no”: no activation
More information is in paragraph “Opened window detection”
Default value: Yes Values: Yes / no
Authorization or not of cooling mode:
This parameter menu appears only if digital thermostat is
associated with a Touch screen BT-CT02 or a 6Z master.
It permits to allow or not cooling system in remote room.
Factory setting value: Yes Other values: no
PIN code activation:
“Yes”: activation of function
“no”: no activation
More information is in paragraph “code PIN description”
Factory setting value: no Values: Yes
Operating mode of thermostat:
- Hot: heating mode
- CLd: cooling mode
- rEv: activation of reversible menu
- Aut: automatic mode
This parameter menu appears only if digital thermostat
isn’t associated with a Touch screen BT-CT02 or a 6Z
master.

14 BT-D03-MOI-FR-W-EN-06-19
ENGLISH ENGLISH
EN EN
Setting value for PIN code:
User has to configure values of the three digits with and
validate its choice with validation key.
Factory setting value: 000 Value range: 000 to 999
Reset user settings:
Press and hold for 5 seconds to reset, all segments light
up, showing that the thermostat has been reset with the
factory default setting:
➤Set point temperatures in modes,
➤All user parameters with their factory values.
When button is hold:
Zone number displaying:
This function is available only if digital thermostat is associ-
ated with a multi-zone receiver.
Displaying client software version:
Pressing and maintaining key displays software qualifi-
cation version and debug information.
Reminder:software version is written: Vxx.xx.
Professional menu:
This menu permits to access to installer parameter menus.
Pressing and maintaining key displays first parameter of
installer menus.
When button is hold:
User menu exit:
Press key to exit user menu and return to the main
screen.
keys and (step of 0.1°C).
The setting is validated with key .
Clearing user parameters
holding
button
holding
button
releasing
button
Clearing
is done
Accessing to installer parameters
holding
button
holding
button
releasing
button
Installer
parameters

15
BT-D03-MOI-FR-W-EN-06-19
ENGLISH ENGLISH
EN EN
8. INSTALLER PARAMETER DESCRIPTION
To access to these installer parameters, installer has to go to user parameter number 15.
After, he presses and holds validation key during 5 seconds:
Selecting temperature sensor used for the regulation:
- AIR: regulation with internal sensor
- Amb: regulation with external sensor
- FLR: regulation on floor sensor (external sensor of remote,
only when thermostat is connected to master) or embedded
sensor on receiver
- FLL: regulation with floor sensor and air sensor
Factory setting value: Air Other values: Amb / FLL / FLR
Lower limit of floor temperature (FL.L)
This value is used when parameter 20 is FLL
Factory setting value: “no”: not activated
Other values: 5°C to “FL.H”
High limitation of floor temperature (FL.H)
This value is used when parameter 20 is set on “floor limit”
FLL.
Factory setting value: “no”: not activated
Other values: “FL.Lo” to 40°C
Displaying of measured temperature by floor sensor
connected to receiver (only with specific bidirectional
system)
If “Err” is displayed, thermostat isn’t associated to a received
with floor sensor or this sensor is damaged.
Displaying of measured temperature by internal sensor:
If “Err” is displayed, internal sensor is damaged.
Displaying of measured temperature by external sensor:
➤FLOOR temperature / AMBIENT temperature
If “Err” is displayed, external/ambient sensor isn’t connected
or damaged.
Accessing to installer parameters
holding
button
holding
button
releasing
button
Installer
parameters

16 BT-D03-MOI-FR-W-EN-06-19
ENGLISH ENGLISH
EN EN
Regulation type:
- HYs: regulation of hysteresis
- bP: regulation of proportional type
Factory setting value: bP Other values: HYs
Hysteresis value:
This menu is displayed only if parameter “typ” is equal to
“HYs”. Use and keys to set hysteresis value. The setting
is validated with key .
Default value: 0.3°C Value range: 0.2°C to 3°C
Choice of concrete type:
Two choices are possible:
- uf1: for thin liquid concrete < 6 cm
- uf2: for traditional concrete with a thickness higher than 6 cm
if parameter #26 is set to “HYs” this menu is not available.
Factory setting value: uf1 Other values: uf2
Choice of coating:
Two choices are possible:
- bP1: for tiling
- bP2: for wooden floors (floating or not)
if parameter #26 is set to “HYs” this menu is not available.
Factory setting value: bP1 Other values: bP2
Function of pilot wire:
This option is used to enable the pilot wire functionality if it’s
used on your installation.
Factory setting value: no Other values: yes
Minimum value of setting range of the set point
temperature:
Factory setting value: 5.0°C Other values: 5.0°C to 15.0°C
Maximum value of setting range of the set point
temperature:
Factory setting value: 37.0°C Other values: 20.0°C to 37.0 °C
Humidity set point (Optional)
Factory setting value: 75 % Other values: 0% (“no”) to 100%

17
BT-D03-MOI-FR-W-EN-06-19
ENGLISH ENGLISH
EN EN
User menu exit:
Press key to exit user menu and return to the main
screen.
Displaying of “Err”
and red LED blinking
Icon blinking
and red LED blinking
Backlight ON:
Icon blinking
and red LED blinking
Icon blinking
and red LED blinking
Anti-condensation function of the installation:
When condensation is detected, air conditioning is stopped
or/and dehumidifier is activated.
Factory setting value: yes Other values: no
Internal sensor error
External sensor
Low batteries
RF error
(only when remote is
associated to smart
home or master product)
EEPROM clearing:
All thermostat parameters will be loaded with factory set-
tings. RF wireless communication will be reset too.
Pressing and maintaining key displays:
9. TROUBLESHOOTING & SOLUTION
Description of thermostat errors displaying
Remote errors are:
➤Error of temperature measurement o Internal sensor;
o External sensor.
➤Low batteries
➤Loss of RF communication (only when remote is associated to Touch E3 or to master product).
Accessing to installer parameters
holding
button
holding
button
releasing
button
Clearing
is done

18 BT-D03-MOI-FR-W-EN-06-19
ENGLISH ENGLISH
EN EN
On the receiver:
- Check the good reception of RF signal.
- Check the connections.
- Check the power supply of the heating element.
- Contact your installer.
Check the following points:
- The receiver must be put at a minimum distance of 50 cm of all others electrical or
wireless materials (GSM, Wi-Fi..)
- The receiver shouldn’t be fixed on a metallic part or too close of hydraulic pipes... (Copper...)
- Try to calibrate your thermostat (refer to user parameter 05).
- Contact your installer, to check & adjust the regulation parameters with your heating
system.
The logo blinks:
- Cooling request is made by the central (BT-CT02) but the thermostat doesn’t allow
(refer to user parameter 08).
Output
RF communication
Sensor calibration
Configuration
My Thermostat seems work correctly but the heating or the cooling doesn’t work correctly
0°C - 40°C
-10°C to +50°C
0,5°C step
5°C to 37°C
0,5°C to 10,0°C
5°C to 37°C
2 AAA LR03 1.5V Alkaline ~2 years
868 MHz, <10mW.
0.1°C
Proportional Band (PWM 2°C/10min) or Hysteresis 0.2°C to 3.0°C
Internal: NTC 10kW at 25°C
External: NTC 10kW at 25°C (ß = 3950)
IP30
Class II
2
Environmental:
Operating temperature
Shipping and storage temperature
Setting temperature range
Comfort, Reduced
Holiday (Antifreeze)
Timer
Power supply operating life
Radio frequency
Temperature precision
Regulation characteristics
Sensing elements:
Internal & External (option)
Electrical protection
Installation category
Pollution degree
11. TECHNICAL CHARACTERISTICS
10. MAINTENANCE
Battery level indication
The batteries are considered weak when
voltage level is too low for a correct prod-
uct functionning.
The icon will blinked on LCD screen.
Cleaning of the thermostat
Gently dust the outside of the thermostat
with a soft, lint-free cloth.
If the thermostat needs a more thorough
cleaning:
- Lightly dampen a soft and clean cloth
with water.
- Wring out any excess water from the cloth.
- Gently wipe the display and sides of the
thermostat, making sure no drops of water
accumulate around the product.
Important: Do not spray thermostat direct-
ly with water, or use cleaning solutions or
polishes, as doing so may damage the
thermostat.

19
BT-D03-MOI-FR-W-EN-06-19
ENGLISH ENGLISH
EN EN
Showed in parameter menu. Vers 14Software version
BT-M6Z02 RF - BT-FR02RF
BT-WR02RF / BT-WR02HC
BT-PR02RF - BT-CT02
Other receivers can be compatible, check on the instruction manual of
your receiver.
UE 811/2013 and 2010/30/UE
IV
(2%)
Compatible receivers
Product conformed to
Classification
Contribution
17 mm
83,5 mm
83,5 mm 60 mm
11.1 Dimensions & weight
12. DIRECTIVES
Description Link
The Low Voltage Directive (LVD) (2014/35/EU)
ensures that electrical equipment within certain
voltage limits provides a high level of protection
for European citizens, and benefits fully from the
Single Market.
The Radio Equipment Directive 2014/53/EU (RED)
establishes a regulatory framework for placing
radio equipment on the market.
The WEEE Directive (2012/19/EU) aims to reduce
the amount of waste electrical and electronic
equipment that ends up in landfill.
The Electromagnetic Compatibility (EMC) Directive
2014/30/EU ensures that electrical and electronic
equipment does not generate, or is not affected by,
electromagnetic disturbance.
Directive on the restriction of the use of certain
hazardous substances in electrical and electronic
equipment.
Ecodesign requirements for local space heaters.
2014/3
5/UE
2014/5
3/EU
2012/1
9/EU
2014/3
0/UE
2011/6
5/EU
2015/1
188
Designation
Low Voltage Directive (LVD)
2014/35/EU
Radio Equipment
Directive (RED) 2014/53/EU
Waste Electrical
& Electronic Equipment
Directive (WEEE)
Electromagnetic
Compatibility (EMC)
Directive 2014/30/EU
Restriction of the use of cer-
tain hazardous substances
Directive (RoHS) 2011/65/ EU
Ecodesign Commission
Regulation (EU) 2015/1188
Weight: 115g (thermostat only) - all inluding box 220g

BT-D03-MOI-FR-W-EN-06-19 © 2019 / 06 Watts
Watts Electronics S.A.S
B.P. N°10 - Z.A. des Tourettes, 43800 ROSIERES, France,
T: [phone], F: [phone],
www.wattswater.eu
The descriptions and photographs contained in this product specification sheet are supplied by way of information only and are not binding. Watts Industries reserves the right to carry out
any technical and design improvements to its products without prior notice.” Warranty: All sales and contracts for sale are expressly conditioned on the buyer’s assent to Watts terms and
conditions found on its website at www.wattswater.eu Watts hereby objects to any term, different from or additional to Watts terms, contained in any buyer communication in any form,
unless agreed to in a writing signed by an officer of Watts
United Kingdom
Watts Industries UK Ltd
Colmworth Business Park
Eaton Socon
St. Neots
PE19 8YX United Kingdom
T: [phone]
F: [phone]
Email: [e-mail]
http://wattswater.co.uk
Germany, Austria and Switzerland
Watts Industries Deutschland GmbH
Godramsteiner Hauptstr. 167
76829 Landau
Germany
T: [phone]
F: [phone]
Email: [e-mail]
http://wattswater.de
France
Watts industries France
1590 avenue d’Orange CS 10101 SORGUES
84275 VEDENE cedex - (France)
T: [phone]
F: [phone]/39
E-mail: [e-mail]
http://wattswater.fr
Belgium
Watts Benelux
Beernemsteenweg 77A
8750 Wingene
Belgium
T: [phone]
F: [phone]
Email: [e-mail]
http://wattswater.eu
Netherlands
Watts Water Technologies Benelux
Kollergang 14
6961 LZ Eerbeek Netherlands
Tel: [phone]
Email: [e-mail]
http://wattswater.eu
Italy
Watts Industries Italia S.r.l.
Via Brenno, 21
20853 Biassono (MB)
T : +39 039 4986.1
F: +39 039 4986.222
Email: [email protected]
http://wattswater.it
Spain
Watts Ind. Ibérica, S.A.
Pol. Ind. La Llana - Av. La Llana, 85
08191 Rubí (Barcelona) Spain
T: [phone]
F: [phone]
E-mail [email protected]
http://wattswater.eu
Denmark, Sweden, Norway and Finland
Watts Industries Nordic AB
Godthåbsvej 83
DK-8660 Skanderborg
T: [phone]
F: [phone]
E-mail: [e-mail]
http://wattswater.eu
Bulgaria
Watts Industries Bulgaria
Industrial zone Trakia
33, Nedyalka Shileva Str
P.O. Box 55 (post-oce Trakia)
4023 Plovdiv, Bulgaria
T: [phone]
F: [phone]
E-mail: [email protected]
http://wattswater.eu
Poland
Watts Industries Polska sp.z o.o.
Puławska 40A
05-500 Piaseczno
T: + 48 22 702 68 60
F: + 48 22 702 68 61
Email: [e-mail]
http://wattswater.pl
Russia
Контакты
http://wattsindustries.ru/contacts/
http://wattsindustries.ru