Waves LIVE Calrec SoundGrid User manual

User Guide
Calrec SoundGrid I/O

Calrec SoundGrid interface/ User Guide
2
Contents
INTRODUCTION................................................................................................................................................................. 3
HARDWARE AND CONNECTIONS ................................................................................................................................... 4
GETTING STARTED........................................................................................................................................................... 5
Connect the Hardware ..................................................................................................................................................... 5
One I/O......................................................................................................................................................................... 5
Add I/Os ....................................................................................................................................................................... 6
Download and Install Software ........................................................................................................................................ 7
Configure the System ...................................................................................................................................................... 8
Manual Device Configuration ....................................................................................................................................... 9
Automatic Device Configuration with SoundGrid Studio .............................................................................................. 9
Device Firmware ........................................................................................................................................................ 10
USING AN I/O DEVICE WITH A DAW .............................................................................................................................. 11
Waves Inc
2800 Merchants Drive, Knoxville, TN 37912 USA
1-865-909-9200
www,waves.com

Calrec SoundGrid interface/ User Guide
3
Introduction
The Calrec SoundGrid Interface Card makes it possible to run Waves plugins directly from selected Calrec mixing
consoles. The card connects to a SoundGrid host, which controls I/O devices, drivers, and an optional SoundGrid DSP
server, all via standard Ethernet cables.
This Calrec Modular Card is compatible with the Apollo, Artemis, RP1, Summa, Brio 12 and Brio 36 models. Each card
allows 64 channels of bi-directional audio.
SoundGrid is the Waves high-speed networking protocol for moving audio, clock, and other information between a host
system and I/O devices—and between I/O devices themselves. A SoundGrid host manages the network and assigns
servers and I/O devices to mix, process, and record, depending on the host. All SoundGrid devices connect to the host
with standard Ethernet cable.
SoundGrid is scalable. Connect one I/O device to a DAW and you have a high-quality sound card. Add more I/Os and
your system becomes more flexible and powerful. Depending on the host application, a SoundGrid host can assign up to
sixteen I/O devices. Complete SoundGrid systems can be networked together to share devices.
Add a server to a SoundGrid system to offload plugin processing from the host CPU to a SoundGrid DSP server. This
dramatically increases processing power and enables greater plugin counts—it also provides very low system latency.

Calrec SoundGrid interface/ User Guide
4
Hardware and Connections
Please refer to the user guide for your Calrec mixing console for installation instructions. Calrec documentation can be
downloaded from the Calrec website.
SoundGrid Port 1 and Port 2 connect to the SoundGrid Network via
Cat5e or Cat6 Ethernet cables.
Each Ethernet port has lights that indicate status:
Link/Act LED = flashing green
GigE (Gigabyte Connection Indicator) = solid green
The Calrec SoundGrid I/O has two SoundGrid Ethernet ports. This enables you to connect a host
computer and another device (e.g. an additional I/O or SoundGrid server), without needing an
Ethernet switch. For installations that include more than two SoundGrid devices, a switch is
necessary. It is not important which Ethernet port is used to connect to the SoundGrid network.
To learn more about installing the card in your Calrec console, please refer to the CDC manual.

Calrec SoundGrid interface/ User Guide
5
Getting Started
All SoundGrid systems, regardless of size, are set up in the same manner:
Connect the hardware
Install the software
Configure your system
Connect the Hardware
One I/O
Here, one Calrec SoundGrid I/O interface card is used to connect a console to the SoundGrid host application
SoundGrid ASIO/Core Audio driver for plugin processing and/or DAW playback/recording. The interface is connected
directly to the host using a Cat 5e Ethernet cable or better.
Host computer with SoundGrid application
Calrec console with one SoundGrid I/O
The host computer’s LAN port that’s connected to the SoundGrid network should be used for SoundGrid only. Do not
share this port with the internet or other networks.
In this configuration, all plugin processing is carried out on the host computer. The speed and power of the host defines
overall latency.

Calrec SoundGrid interface/ User Guide
6
Add I/Os
Adding I/O devices not only increases the number of I/O channels, but lets you have separate devices for stage and
FOH, or live room and control room. When there are more than two network connections, use a "star" network
configuration with a 1GB Ethernet switch. Only use switches tested and approved by Waves.
Host computer
Calrec console with SoundGrid I/O
Additional SoundGrid I/O
1GB Ethernet switch
See this support article for a list of supported
switches.
You can connect and assign up to 16 SoundGrid I/O devices to the network, depending on the SoundGrid host
application. You can also add more computers to enable audio streaming between hosts.
ADD A SERVER
To add a server to your SoundGrid system, just connect it to the Ethernet switch and configure it in your host application.
This moves all DSP processing from the host computer to the server, which provides a higher plugin count and enables
the eMotion LV1 and ST mixers. Visit the waves.com hardware pages to learn more about SoundGrid servers. Consult
your host application user guide to learn how to configure additional I/Os and servers.

Calrec SoundGrid interface/ User Guide
7
Download and Install Software
INSTALLING A NEW SOUNDGRID HOST SYSTEM
Installing the Waves SoundGrid host application will also install all applicable device drivers and ASIO/Core Audio
drivers. Your devices will appear in the Inventory of your host system. If a device is not visible in the Inventory, you may
need to install a specific driver from Waves Central—please see below. First, however, check the device’s connections
and power.
ADDING AN I/O DEVICE TO AN EXISTING SOUNDGRID HOST SYSTEM
If you are already using a Waves SoundGrid host application and your device does not appear in the Network Devices
list, use Waves Central to update the host application, which also updates the device drivers—or install just the missing
device driver from Waves Central.1
Waves Central
All Waves software is downloaded and installed via the Waves Central application. To install a specific device
driver, launch Waves Central and follow these steps:
Choose All Products
Search for the driver by name
Choose the driver and click Install
If you are new to Waves products, begin by downloading the Waves Central installer from the Waves Download
Page. See the Waves Central User Guide for instructions on how to install drivers, plugins, and applications.
LICENSES
You do not need a license to use this device. However, many hosts or specific host configurations do require a license.
Refer to your host’s product page for details.
1The SoundGrid QRec host is installed with any I/O.

Calrec SoundGrid interface/ User Guide
8
Configure the System
A SoundGrid network is configured and devices are assigned in a host’s Setup window. At the heart of this window are
racks where devices are assigned. Any compatible device that’s part of the host’s SoundGrid network will be available for
assignment. This collection of devices is called the Inventory. Setup is similar with all hosts: identify the host’s LAN port,
select a device slot, and use the drop-down menu to choose an available device.
Please consult the user guide of your host application for specific instructions.
All SoundGrid devices are configured in a similar manner. Throughout this section, we show DiGiGrid IOS as an
example.
SoundGrid QRec
SoundGrid Studio Setup Window

Calrec SoundGrid interface/ User Guide
9
Manual Device Configuration
You can assign, remove, and manage a device manually. Click on the plus or arrow
symbol in a device slot to open its the Device Menu, then select a device.
Any device not already used will be available for assignment. If no other
devices are assigned, the current device will become your clock master.
Drivers and servers are assigned in the same manner.
See the user guide of your host system for specific instructions on device
assignment and I/O channel patching.
Automatic Device Configuration
Certain SoundGrid hosts—including SoundGrid Studio, eMotion LV1 or SuperRack SoundGrid—offer an Auto-
Config tool. Once your devices are connected and powered up, click Auto to start the configuration.
Auto-Config chooses the correct LAN port on the host computer and scans the SoundGrid network for devices. It then
patches the devices to the host. We recommend that you let Auto-Config take care of things, at least when you are
getting started. If later you add, remove, or swap a device, Auto-Config will reconfigure your inventory and re-patch.
Note that SoundGrid Studio assigns the SoundGrid driver automatically. SuperRack SoundGrid and eMotion LV1 require
that the SoundGrid ASIO/Core Audio driver is assigned manually.
SoundGrid QRec
SoundGrid Studio

Calrec SoundGrid interface/ User Guide
10
Device Firmware
An I/O that is using outdated or incompatible firmware will not work properly in a SoundGrid network until its firmware is
updated. The color of the FW button in a device slot indicates the current firmware status.
If a device requires updated firmware, click on the FW button to start a hardware scan. Do not disconnect the device or
turn off the computer before Done appears. Once the update is ready, turn the device off and on to reset.
Grey Compatible firmware
Blue Compatible firmware, but a newer version exists
Red
Firmware not compatible and must be updated in order to use.
SoundGrid Studio
SoundGrid QRec