Wavtech bassRESTOR User manual
bassRESTOR
Bass
Restoration Processor/
LOC
/
Line
Driver
Complete Tuning Control • Auto Turn-On • Multi-Function Remote
□
0
□
0
□
0
□
0
0
□
0
□
0
□
8
□
0
Owner's Manual
bassRESTOR
£\;:,
wavtech
~-BASS
PROCESSOR-~
0
CLIP
EFFECT
WIDTH
FREQ
SUBSONIC
®
GAIN
® ® ®
I®
MIN MAX
NAR
WIDE
30
(H,)
80
15
(H
,)
SO
----i:±=====---...:.....:...._
_______
-----'='
www.wavtech-usa.com
0
&WARNING
This symbol means
important
instructions.
Failure
to
heed them
can
result in serious injury
or
death.
&CAUTION
This symbol means
important
instructions.
Failure
to
heed them can result in
injury
or
property
damages.
&wARNINCi
•
DO
NOT
DRIVE WHILE DISTRACTED. Any function
that
requires
your
prolonged
attent
ion should
not
be performed
while driving.Always stop
the
vehicle in asafe location before
perform
i
ng
any such function. Failure
to
do
so
may
resultin
an
accident.
• KEEP THE
VOLUME
AT MODERATE LEVELS WHILE
DRIVING.
Excess
volume levels
can
obscure sounds such
as
emergencyvehicle sirens
or
road warning signals and may result in
an
accident.Continuous exposure
to
high sound
pressure levels may cause permanenthearing loss. Use common sense and practice safe sound.
• FOR USE
WITH
12V
NEGATIVE GROUND VEHICLEAPPLICATIONS ONLY. Using this product
other
than in its
designed application may result in fire, injury
or
product damage.
• MAKE
THE
CORRECT WIRING CONNECTIONS
AND
USE PROPER FUSE PROTECTION. Failure
to
connect wiring
correctly
or
use appropriate fuse protection
may
resultin fire, injury
or
product damage.Ensure
proper
fusing
of
all
system
power
wiring and install a 1-amperein-line fuse
(not
included)
with
the
+1
ZV
lead
to
the
unit's
power
supply
connector.
• DISCONNECT
THE
NEGATIVE BATTERY
TERMINAL
BEFORE INSTALLATION. Failure
to
do
so mayresultin fire,
injury
or
damage
to
the
unit
.
•
DO
NOT
ALLOW CABLES TO BECOME ENTANGLED
IN
SURROUNDING OBJECTS. Arrange wiring and cables
to
preventobstructions when driving. Cables
or
wiring
that
obstruct
or
hang up on places such
as
steering wheel, brake
pedals, etc.
can
be extremely hazardous.
•
DO
NOT
DAMAGE VEHICLE SYSTEMS
OR
WIRING WHEN DRILLING HOLES. When drilling holes in
the
chassis
for
installation, take precautionsso
as
not
to
contact, puncture
or
obstruct
brake lines, fuel lines, fuel tanks, electrical
wiring, etc. Failure
to
take such precautions may resultin fire
or
an
accident.
•
DO
NOT
UTILIZE OR CONNECT TO
ANY
PART
OF
VEHICLE SAFETY SYSTEMS. Bolts, nuts
or
wires used in
the
brake, airbag, steering
or
any
other
safety-related systems
or
fuel tanks should
NEVER
be used
for
mounting,
power
or
ground connections. Using such parts may disable control
of
the
vehicle
or
result in fire.
&cAUTION
• STOP USE IMMEDIATELY IF A PROBLEM OCCURS. Failure
to
do
so may resultin personal injury
or
damage
to
the
product.Return
it
to
your
authorized Wavtech dealer.
• HAVE
AN
EXPERT
DO
THE
WIRING
AND
INSTALLATION. This
un
it requires special technical skill and experience
for
wiring and installation.
To
insuresafetyand proper function, always contact
the
authorized dealerwhere you
purchased
the
product
to
have
it
done professionally.
• INSTALL
THE
UNIT
SECURELY
WITH
SPECIFIED PARTS.
Be
sure
to
use only the included partsand specified
installation accessories
(not
included).
Use
of
other
than designated parts may damage this
unit
. Install
the
unit
securely so
that
it
will
not
come loose during acollision
or
sudden
jolt.
• ROUTE WIRING AWAY FROM SHARP EDGES
AND
MOVING
PARTS. Arrange cables and wiring away
from
sharp
or
pointed edges and avoid moving partssuch
as
seat hinges
or
rails
to
prevent pinching
or
wear.
Use
loom
protection
whereappropriateand always use a
grommet
for
anywiring routed through metal.
• NEVER RUN SYSTEM WIRING OUTSIDE OR UNDERNEATH
THE
VEHICLE. Allwiring must be routed, secured and
protected inside
the
vehicle. Failure
to
do so may resultin fire, injury
or
property
damage.
• INSTALL
THE
UNIT
IN A DRY
AND
VENTILATED LOCATION.Avoid mounting locationswhere
the
unit
will
likely be
exposed
to
high moisture
or
heat
without
adequate ventilation. Moisturepenetration
or
heat buildup may result in
product failure.
• REDUCE GAIN
AND
SOURCE
VOLUME
TO
MINIMUM
LEVELS FOR
INITIAL
SYSTEM
TUNING
AND
BEFORE
CONNECTION
TO
AN
AMPLIFIER. Ensure amplifierpower is
off
before connecting
RCA
cables and
follow
proper
system gain setting procedure. Failure
to
do
so
may result in damage
to
the amplifierand/orconnected components.
Package Contents:
Main
Unit
Terminals
---
----
ff
Ty
PWR
/SPK
GND
Mounting Tabs
(detachable)
ww
1
Remote Level Control
Remote Cable
(16.
4ft
/
Sm
)
~
Accessories Required
for
Installation
(not
included):
•
RCA
Interconnects
• 18AWG Wire
• In-line
Fuse
Holder
w/1A
fuse
• BatteryRing Terminal
• Wire Crimp Connectors
• Grommets and Loom
• Cable Ties
•
Mount
ing Screws
Introduction
Welcome
to
Wavtech, exceptional mobile audio integration products
for
audiophiles.
Our
products are
engineered
to
provide a
truly
remarkable listening experience. Built
for
the
professional installer,
our
OEM
integration and signal processor models are simply
the
best solution available
for
unlimited sound
system upgradeswhile retaining
the
factory receiver
or
with
an
aftermarket
source.
Features
•
Bass
Restoration Processor
· CompleteTuning Control (Effect, Width, Freq)
· Variable Subsonic Filter
• Multi-Function Remote
· Total
Output
Level
·
Bass
Effect
Level
with
Push
On/Off
• Line
Output
Converter
or
Line Driver
•
Differential
Balanced Inputs
• Low Impedance
Outputs
Connections & Functions
O
PwR
@ 0 ~
REM-,
8 2000
GND
+12V
IN
OUT
ISO
~
l~~~~I
@
-,le
PWR
SUPPLY SPK
INPUT
• Variable
Gain
with
Clip
LED
• Auto Turn-On via DC-Offset
or
Audio Signal Detect
• Generated +12V Remote
Output
•
OEM
Load Detect Compatible
• Selectable Ground Isolation
• Locking Detachable Power/SpeakerTerminals
• Panel
Mount
RCA
Jacks
• CompactAluminum
Chassis
• Detachable Mounting
Tabs
0 PowerIndicator: This red
LED
indicates when the
bassRESTOR
is powered on. Once illuminated, there
will
be a
short
delay before audio signal
output
is enabled. During initial
power
connections,
it
may
illuminate
for
a
brief
period.
8 Ground Jumper: For selecting between chassis, isolation
or
2000
for
the
internalaudio signal ground.
Chassis
ground
is
the
default
setting and ideal
for
most
applications due
to
the
differential
input
stage.
In
the
rare
case
there
is
system noise present
after
all
other
installation countermeasures,
changing this
jumper
to
ISO
or
2000
may reduce
or
eliminate
the
noise.
0 PowerSupplyTerminal: For +12V battery, chassis ground, remote
input
and remote
output
wire
connections.A minimum
of
18AWG wire
is
recommended
for
powerand ground connections. Always
protect
the
+12V
power
wire
with
a 1-amp fuse.
8 Speaker Level
Input
Terminal: For
left
and
right
channel speakerlevel(a.k.a. high level) connections
to
the
source. In
the
default
setting,
input
signals ranging from 4Vrms
to
40Vrms
will
produce up
to
10Vrms
RCA
output
from maximum
to
minimum gain.
If
after
adjusting all
other
settings the
bassRESTOR's
output
is
not
enough
to
maximize system levels
at
the
desired source volume range,
internal
jumpers
are available
to
increase
input
sensitivity by
two
times (+6dB)
for
2Vrms
to
20Vrms.
0
RCA
Input
Jacks: For
left
and
right
channel
low
level (a.k.a. line level) signal connections
to
the source.
In
the
default
setting,
input
signals ranging
from
1Vrms
to
10Vrms
will
produce up
to
10Vrms
RCA
output
from
maximum
to
minimum gain.
If
more
output
is desired
after
making all
other
system
adjustments,
the
input
sensitivity range may be increased by
two
times (+6dB) via internaljumpers
for
0.SVrms
to
SVrms.Additionally, these di
fferential
inputs may be set
to
unbalanced via internal
jumpers
if
required
for
a particularsource
or
to
midigate
potential
for
coupled noise
if
left
floating.
0 Remote Level
Control
Jack: This
RJ45
jack
is
for
connecting
the
remote level
control
to
the main
unit
with
the
supplied cable. A standard
ethernet
cable may also be used.
8
RCA
Output
Jacks: For
left
and
right
channel line level signal connections
to
your
amplifier(s).
Each
output
is
capable
of
driving
multiple
amplifier
input
channels in parallel.
Use
quality interconnects
to
ensure stable connection and minimize the possibility
for
induced noise.
0
Mounting
Tabs:
These mounting tabs are pre-attached and should be used
to
properlysecure
the
bassRESTOR
during installation
with
screws
or
cable ties. They are removable
if
the
unit
can
be safely
secured by
another
method.
0 Remote Housing: This 2-piece housing design provides
both
convenient mounting
and simple dissasembly
for
customization. The integratedscrew
mount
tabs are
pre-scored
to
aid removal
if
securing by
another
method, and
the
lower
housing
can
be detatched by removing the
two
top
screws. Forcustom panel mounting,
the
housing
can
be completely disassembled
by
also removing the main knob,
outer
ring,
shaft
nut,circuit board screw and relocating the
LED.
If
the housing
is
removed,
it
is recommended
to
protect
the
exposed
PCB
with
heat shrink. 2
Installation & System Wiring
It
is
important
to
read this manual thoroughly before starting
your
installation and always plan
accordingly. Beforeinstalling any Wavtech product, disconnect the negative (ground)
wire
from
the
vehicle's
battery
to
avoid damage
to
thevehicle
or
yourself. Following allguidelines
will
help provide
years
of
enjoyment
with
your
Wavtech
bassRESTOR
audio interface.
Ground Connection
(GND):
The
GND
terminal
must
be connected
to
a metal
part
of
the
vehicle
that
is
welded
to
the
vehicle body
with
ground plane back
to
the
main
battery
ground
attachment
point
(a
.
k.a
.
chassis ground).This
wire
should be a minimum
of
1
SAWG
and
as
short
as
possible
to
minimize
potent
ial
for
noise
to
enter
the
system.The chassis ground connection
point
should have all
of
the
paint
removed
and be scuffed
to
the
bare metal.The ground
wire
should be terminated by a ground specific interlocking
terminalsuch
as
the
included
EARL
terminal
or
ring terminal securely bolted
to
the vehicle
with
star
or
lockwasherand
nut
to
prevent from coming loose. Avoid using factory ground points
to
reduce
the
chance
of
induced noise from
other
components.
PowerConnection (+12V): The constant
power
connection should be made
at
the vehicle
battery
when
possible. For
direct
battery
connection, a 1-amp fuse
must
be installed in-line
with
the
power
wire
within
1
S"of
the
battery
and securely connected
to
the
positive
battery
terminal
bolt
with
a ring terminal.
If
connecting
to
another
available
constant+
12V
power
source,a 1-amp in-line fuse
must
be added
at
the
connection point. The power
wire
should be a minimum
of
1
SAWG.
Do
not
install
the
fuse
until
all
other
system connections have been made.
Speaker Level
Input
(SPK):
Connect
the
speakerwires
from
the
source
unit
to
corresponding terminals on
the interface.
Use
the
SPK
input
if
your
source
unit
is
not
equipped
with
RCA
outputs
.Always ensure
the
correct
polarity
of
each channel when making these connections,
as
failure
to
do
so can severely
effect
sound performance.
Remote
Input
(REM
IN):
If
the
source
unit
has a remote
output
wire
(provides +12Vonlywhen turned on),
connect
it
to
the
REM
IN
terminal.
If
a remote lead
is
unavailable, all Wavtech interfaces also provide
automatic
turn
-on via DC-offsetand audio signal detection. While auto turn-on
will
work
in
most
applications, there may be some
cases
were a +12V
trigger
is needed
for
satisfactory results. These signal
detect
functions
can
also be individually defeated via internaljumpers (labeled
DC
and AUD)
if
necessary.
Remote
Output
(REM
OUT):
Use
the remote
output
to
provide a +12V
trigger
to
turn
on amplifiers
or
other
components.This
+12Voutput
is generated internally by the interface when turned on
either
by
REM
IN
or
signalsensing, and
will
provide over S00mA
of
constantcurrent
for
externaldevices.
Remote Level Control
(RLC)
: Connect
the
remote
to
the
bassRESTOR's
RLC
port
with
the
supplied
16.4ft/5m
cable. Plan cable routing before mounting
the
remote
to
ensure proper
length
.
If
additional
length
is
required, astandard a-conductor
CATS
or
CAT6
ethernet
cable
or
extension may be used.The
cable may also be shortened and re-terminated
with
a RJ45 connectorand
ethernet
crimping tool.
System Examples
Example-1: Speaker Level Input from OEM Radio
~
o
I'---------'
DDDDDD
RCA
OUT
RLC
REM
OUT
Note: When using a receiver's internal power
IC
to
drive speakers directly, note
that
its
speaker
outputs
will
likelyclip
below the maximum mastervolume level. Adjustgain settings accordingly
for
opt
imum unclipped volume range.
Example-2: Speaker Level Input from OEM Amplifier
@ o +12V
0 I I
RCA
OUT
-
l~
GND
0
DDDDDD
!-!=
-~
n=
/,
-r,
~
Et)-
SPKIN [;.r-i
~-;]
ti
• •
Uf
~
~
~~t
~OJ
In
-r l
RLC
REM
OUT
Note: In vehicleswhere the factory radio has afixed level
or
digital
output
to
a factory ampl
if
ier, signal
fo
r the
bassRESTOR's
speaker level
input
should be connected
at
the amplifier's
output
.
3
-
~~
......
Example-3:
RCA
Input from
Aftermarket
Radio
Eo0l
oo
_0000000:c
REMIN
GND
•
REM
OUT
Note:
If
the
source's
output
signal is full-range and the
bassRESTOR
is being used
for
subwoofer(s) only, a
low
-pass
filter
will
need
to
be engaged
at
theamplifier
to
filter
out
unwanted higher frequencies. Additionally, unless the
amplifier
already has
an
adequate subsonic filter, set the
bassRESTOR
's subsonic
filter
appropriately to preventover-excursion.
Top Panel Adjustments
0 Clipping Indicator: This yellow
LED
indicateswhen the
output
signal
is
at
maximum level
before
distortion
(clipping) occurs.
It
will
be dimly
lit
just
before
the
onset
of
clipping, and
full
bright
at
clipping. Since the
bassRESTOR
can
produce up
to
10Vrms
at
maximum
output,
it
is
likely
that
gain
will
need
to
be
Q
cuP
~----
BASS
PROCESSOR-------.
EFFECT
WID
TH
FREQ
SUBSONIC
{ID
15
(Hz)
50
reduced below the illumination
point
to
match
your
amplifier(s) maximum
input
capability, optimize
source volume range
or
compensate
for
bass restoration applied
after
initialgain setting.
8 Gain Adjustment: This adjustment
is
for
matching the
output
signal level
of
the
bassRESTOR
with
the
maximum unclipped signal provided
by
your
source and the maximum
input
capability
of
your
amplifier(s). Follow proper gain setting procedures
to
ensure optimum source volume range
without
clipping
at
any
point
in the signal chain.
If
using music
to
set system gains,
it
is
recommended
to
utilize
avariety
of
bass contentand recording levels
to
ensure properheadroom and minimize the ability
to
overdrive the system. Readjustment may be necessary
after
any changes
to
other
settings.
0
Bass
Processor: This section provides
full
adjustmentoverall parameters
of
the
bass
restoration
process
as
well
as
asubsonic
filter
.Unlike traditional equilization, this provides tuning flexibility
for
how bass restoration
is
dynamicallyapplied
to
music content
as
well
as
for
differencesbetween
vehicles and subwoofersystems.
0 Effect: Provides adjustment
for
the maximum amount
of
boost
that
can
be
applied by the
bass
restoration process, which depends upon the music contentbeing played
as
well
as
the
width
and
frequency settings. Effectis essentially a
limiter
to
preventoverdriving subwoofers when set
properly.
If
gain
has
already been adjusted, adding more
effect
may cause the
output
to
clip and
require reduction
of
gain
to
achieve final desired unclipped
output
level.
After
effect
level
is
set,
it
is recommended
to
only use the remote's
outer
ring
for
on-the-fly
bass
leveladjustments.
0 Width: This adjustment sets the bandwidth
of
frequencies enhanced by the
bass
restoration
process.A wide setting
will
include more adjacent frequencies
for
a broad
bass
enhancement,
while a narrowsetting
will
only add frequencies closer
to
the chosen center frequency. Note
that
changing the
width
may also require readjustment
of
the
effect
and/orgain settings
to
prevent
clipping
or
overdriving the system.
0 Frequency: This adjustment
is
for
setting the center
of
the frequency range enhanced by the
bass
restoration process, between 30Hz and 80Hz.
8 Subsonic: Provides adjustment
of
the subsonic
filter
cut-
off
point
(F3)
belowwhich all frequencies
are filtered out.Very
low
frequencies
can
waste amplifier power
but
this setting
is
especially
important
for
preventing damage
to
subwoofers from large amounts
of
bass
restoration and
potential
for
over-excursion in ported enclosures below the tuning frequency.
Note
:
The
bassRESTOR
is
capable
of
full-range signal
output
.When used
for
asubwoofer system, a
low
-
pass
filter
(usually
built
into
amplifiers)
will
need
to
be applied and adjusted appropriately
to
remove
unwanted higher frequencies.
If
the subsonic and a low-pass filter's
cut-off
pointsare
set
too closely
together, onlya narrow frequency range
will
pass
through and
will
result in reduced
output.
4
Remote Adjustments
0
Bass
Restoration On/Off: By
short
pressing the main knob, the
bass
restoration circuit
can
be activated
or
completely bypassed. This function
provides quick ability
to
defeat
the
effect
for
music content
that
already
has
enough
bass
without
changing the
bass
effect
levelsetting from the
outer
ring. The
LED
will
be illuminated onlywhen
bass
restoration
is
on.
8 Total
Ouput
Level: Rotating the remote's main knob provides attenuation
adjustment over the
total
RCA
output
level,
from
full
output
0dB down
to
-30dB.
It
can
be used
as
a subwoofer level
or
mastervolume control and
functions
whether
or
not
bass
restoration is active.
@
Bass
EffectLevel: Rotating the
outer
ring allows on-the-flyadjustmentover the amount
of
bass
restoration applied, from the maximum
effect
limit
set
at
the main
unit
(0dB) down
to
no
effect
(-oo).
Specifications
5
Frequency Response Max
Flat
(+0/-1dB) 18Hz
to
>75kHz
Extended (+0/-3dB)
-~
15Hz
to
>100kHz
Input Impedance Spk
Input
1800
RCA
Input
20kO
Input Sensitivity Spk
Input
(max-min gain) 2-20Vrms / 4-40Vrms
RCA
Input
(max-min gain) 0.5-5Vrms /
1-1
0Vrms
Max
Input Voltage Spk
Input
peak, <5sec cont. 40Vrms
Output
Impedance
<500
Max
Output
Voltage
at
1%THD+N >10Vrms
THD+N Spk
Input
at
10V
output
<0.05%
RCA
Input
at
10V
output
<0.1%
at
1V
output
>96dBA
Spk
Input
at
4V
output
>107dBA
S/N
at
1
ov
output
>115dBA
at
1V
output
>95dBA
RCA
Input
at
4V
output
>106dBA
at
1
OV
output
>114dBA
Effect
uoto+18dB
Bass
Restoration
Width
Narrow-Wide
Frequency
30Hz-80Hz
Subsonic Filter Slope up
to
-24dB/oct.@ 15Hz
Frequency
(F3)
15Hz-50Hz
Remote Level Control Total Ou
put
Level (Main Knob) 0dB
to
-30dB
Bass
Effect
Level (OuterRing) 0dB
to
-oo
Remote via
REM
IN >10.5V
DC-offset via Spk
Input
>1.3V
Turn-On Trigger via Spk
Input
<100mV
Audio Signal via
RCA
Input
<10mV
Turn-off
Delay up
to
60sec
Remote Output Current Capacity >500mA
Voltage
Within 3%
of
B+
Current Draw Max
Draw
(w/o
REM
OUT) <300mA
Sleep Current <1.2mA
Operating Voltage Power On
(B+)
10.5V-18V
Power
Off
(B+) <8.5V
Main Chassis
1.1
"x3.5"x5.2"
Product Dimensions (HxWxL
not
incl. terminals,jacks) 29x90x133mm
Remote Housing 1.1"x1 .5"x1.8" -
(HxWxD
not
incl. knob,
tab
s)
28x38x45mm
Notes:
•
RCA
and speaker level
input
sensitivity ranges are selectable via combined internaljumpers
(10V/40V
or
5V/20V). The factory
default
RCA/Spk
input
range setting
is
10V/40V.
• DC-offset and/oraudio signal
detect
functions are defeatable via internaljumpers
(DC,
AUD).
•
All
specifications are subject
to
change
without
notice.
Installation Notes
Vehicle Description
•
Year,
Make,
Model:------------------------------
•
Trim
Level/Package:
_____________________________
_
OEM Audio System Info
• Head Unit (type, BT/AUX in, etc.):
__________________________
_
• Speakers (size/location, etc.):
----------------------------
• Subwoofer(s) (size/location,etc.):
_____
_____________
_____
___
_
• Amplifier(s) (location,
output
voltage, etc.):
_______________________
_
•
Other:--------------
-----
----------------
bassRESTOR Connections & Settings
• Installed
Location:-------------------------------
• Wiring {connection locations, signal type, turn-on
mode,
etc):
_________________
_
• Settings (gain, maxmastervol, crossover, etc.):
_______________________
_
•
Other:----------
----
------
---
-------
-----
System Configuration:
------------------------------
Warranty & Service Care
Wavtech warrants this product to be free from defects
in
material and workmanship for a period
of
one
(1)
year when purchased from an authorized Wavtech retailerwithin
the
United States.This warranty
will
be extended to a period
of
two
(2)
years when
the
installation
is
performed
by
an authorized Wavtech
retailer. Avalid sales receipt
is
required to verify eligibility
of
purchase and installation.
This warranty
is
valid only to
the
original purchaserand
is
not transferrable
to
subsequent parties. This
warranty
is
void if
the
productserial number has been altered
or
removed.
Any
applicable implied
warranties are limited
in
duration
to
a period
of
express warranty as provided herein beginning with
the
date
of
the
original purchase
at
retail, and no warranties,
whether
expressed orimplied, shall apply to
this product thereafter. Some
states
do
not
allow limitations on implied warranties, therefore
these
exclusions
may
not
apply
to
you. This warranty gives you specific legal rights.
You
may
also have
other
rights which vary from
state
to
state.
If
your product needs service, you should contact Wavtech Customer Service
to
receive a Return
Authorization
(RA)
Number.
Any
product received withoutan
RA
number
will
be returned to sender.
Once your product
is
received and inspected
by
customerservice, Wavtech
at
its sole discretion,
will
repair or replace itwith a new or remanufactured product
at
no charge. Damage caused
by
the
following
is
not covered underwarranty: accident, abuse, failure
to
follow instructions, misuse, modification,
neglect, unauthorized repair or
water
damage. This warranty does
not
cover incidental
or
consequential
damages. This warranty does
not
cover
the
cost
of
removing
or
reinstalling
the
product. Cosmetic
damage and normalwear are not covered under warranty.
For Service within
the
United States:
Wavtech CustomerService: (480) 454-7017
Monday -Friday, 8:30am to 5:00pm
MST
Important Notice
for
International Customers:
Serial Number:
___________
_
Installation Date:
__________
_ _
Place of Purchase:
___
______
_ _
For
products purchased outside
the
United
States
of
America
or
its Territories, please contactyour local
distributor concerning specific procedures foryour country's warranty policy. International purchases
are
not
covered
by
Wavtech,
LLC.
6
v0219
Wavtech
®
7931
E.
Pecos
Rd
Suite113
Mesa, AZ 85212
{480) 454-7017
©Copyright 2019 Wavtech,
LLC.
All
Rights Reserved.
Table of contents
Other Wavtech Computer Hardware manuals
