Wayel W3 User manual

USER’S MANUALUSER’S MANUAL
FIVE SRL
Via Cerodolo 4 | 40138 Bologna | Italy
T [phone] | www.wayel.it | [e-mail]

Welcome to the family of LX06max owners! We will guide you to know each function for the right and safe use of electric scooters.
To ensure your safety, please read this manual carefully before riding and make sure you are always following the requirements below:
Please contact the Local Customer Service Center if you have any questions about thisscooter.
We are atour service at anytime. Wish you safe andpleasant riding experience!
Fully understand the information in this manual, including butnotlimited to the relevant instructions, precautions and warnings.
Fully understand the operation and contingency measures of electric scooters.
Be fully aware of warning labels of LX06max electric scooters.
We will not take any responsibility resulting from the unauthorized modification, failure to use original spare parts, or installation of components that
affect the performance andsafety of the scooter.
1 2
Whether thehandlebar is stable and flexible when turning.
Whether theswitches on the rightand left handlebars can worknormally.
Whether thespeed accelerator can work normally.
Make sure thetire pressure is normal. Thesuggested tire pressure is 26-29psi for front wheel and 29-32 psi for rear wheel.
Check tire surface for cracks, damage, wear, and foreign matter puncture orattachment
Whether thetread depth is suffcient (>0.8 mm).
Whether any faultwarning light on the instrument panel goes on after being powered.
Whether thebattery is fully charged.
Whether thehead and tail lights,brake lights and winkers can work normally.
Whether thehorn can work normally.
Whether the rear mirrors are clean. Adjust them to theappropriate angle.
Whether thebrake oil is suffcient,and whether thehandlebars and brake system can work normally.
For anyabnormality oroperational concern, please contact local Customer Service Center.
Checks Before Riding
1
2
3
4
5
6
7
8
9
10
11
12
Make sure to check the following items before ridingaelectric scooter, which will guarantee your safety on the road.
RIDING GUIDEUSER INSTRUCTIONS

To ensure the safety of you and others, please make sure to observe the following matters:
Do not ride after you take medications, drink alcohol,orwhen you are unwell,which mayaffect your riding ability.
Observe traffic regulations andtraffc signs and confirm the surrounding road conditions and scooter conditions at anytime to avoid danger.
Wear safety equipment, such as helmet, and appropriate protective clothing if necessary, such as gloves and boots.
Perform a basic check each time before riding, so as to confirm the light, brake, tread and tire pressure and check other parts for looseness or abnormal noise,
and regularly go to Local Service Center for maintenance.
In order to ensure the safety of you and others, please DO NOT use high beam in good lighting conditions. The continuous use of high beam will cause the visual
disturbance to vehicles and pedestrians on the opposite side, thus affecting normal driving.
Pleasedo not make or answer any call during riding,which is likely to causetraffc accidents.
3 4
DESCRIPTION OF COMPONENTS AND PARTS
Installation of Mirrors
Take out the left and right mirrors, insert the hole and rotate the
mirror clockwise to the correct position.
Use the spanner to fasten the nut,make sure the left and right mirror
is on the samelineand suitable for thedriver’s view.
1
2
SAFETY INSTRUCTIONS

35 6
DIAGRAM OF INSTRUMENT PANELDESCRIPTION OF COMPONENTS AND PARTS
Rear direction indicator
Rear combination lamp
Stop lamp/rear position lamp
Converter
Controller
Headlamp
Front position lamp
Speedometer
Rearview mirror
Handle
USB charger
Battery
Horn
Rear registration plate lamp
Direction indicator
Frontsuspension
Motor
Brake error
Motor or motor wire error
Handle or handle wire error
Side stand power off
Error indicator
Power on
Accumulated mileage
Mileage unit
Gear position
Low voltage need
recharge the battery
High beam
Temperature
Speed
Battery capacity
lower beam
Turn signal on
Controller error

Details Of Instrument Panel
7 8
SWITCH FUNCTIONOPERATION GUIDE
M
P
READY
ECU
Power on
Turn signal on
Meter working temperature
Side stand power off
Controller error
Motor or motor wire error
Brake or brake wire error
Handle or handle wire error
Scooter in P position
Low voltage need recharge the battery
Low voltage for the battery to
the limit level
Lamp Function
High beam on
Gear postion display; single driving time
Speed display, km/h & mp/h switch is available;
external plugswitch (off is km/h,on is mp/h)
Battery capacity level
Total milage of thescooter. Speedunit (mile/km)
synchronous switches.
(ODO is accumulated milage.
First showing theaccumulated milage and then
single milage with 0000.0. Speedunit (mile/km)
synchronous switches.
Motor error,erase the error andrun the
motor for 4 minutes, the error indicator
will disappear automatically.
Lamp Function
Left Start Button Right Start Button
1
1
2
2
3
3
Emergency glasher
Push upward the switch,
all turning lights on and flick,
same display on the meter
Push to left and right to
switch on/off the head lamp.
Press the “ Repair” button to
drive the scooter in low speed
when some motor/controller
errors happens.
Item Switch position Functions
Switch of headlight
Repair button
1
2
3
1
2
3
Near-far light switch
High beam is on when turning
on the button
Low beam is on when turning
on the button
Left turning signal on
Right turning signal on
Horn on
Item Switch position Functions
Indicator control
Horn control

Turn the key to postion and power on thescooter.
ATTENTION:
1. Make sure all lights are in “off” condition, oritmay causepower-off protection
due to battery protection programe;
2. If thepower-off protection happen, switch off thelights and restart the circuit
breaker and power on thescooter again.
9 10
Before riding,make sure the electronic side stand retracted and rotate the handlebar to ensure that the handlebar lock is closed.If the Parking button
is pressedwhen riding, the bike will be dis- energized. So DO NOT press it when riding for avoiding danger caused bythe sudden loss of power.
If the electronic side stand is extended when riding, the bike will be dis- energized. So DO NOT extend the electronic side stand when riding for avoiding
danger causedby the sudden loss of power.
The scooter must be fully stopped before starting. In case of abnormality during riding, please ride carefully or push it to a safe place. DO NOT try
restarting the bike duringridingoron the laneso as to avoid danger
OPERATION GUIDE
Guide of ignition key
1Start power supply
1
4
2
3
OPEN
OFF
OPEN
OPEN
SHUT
LOCK
1
2
1
2
Speed levels Press the button to adjust the speed level,
level information will be synchronous shown
in meter
Press the ignition key for 1 second to release the
P gear until the “P” mark in the meter disapper;
The speed regulating function is still effective
when the P gear function is normally turned on;
when the power is on and the whole vehicle stops,
press the P button for 1 second to enter the P gear
postion, the P mark is synchronous in the meter.
Item Switch position Functions
P gear postion
1 2 3
P
SWITCH FUNCTION
2
3
Open the saddle
Handle bar lock and relieve
4The key hole status
Turn the key to left to open thesaddle.
1. Turn thehandle bar to left until stop;
2. Push the key and turn to left till ()position,thehandle baris locked;
3. Push the key and turn to right till ()position,thehandle baris unlocked.
1. The key hole is closed when in ()position;
2. Turn the key towards to ()position，the key hole is in open position.
TIPS:
SHUT

11 12
BATTERY INSTALLATION AND DISMOUNT
Install the cable
Remove the power cord
With the advanced Smart Remote Controller, you can easily lock or unlock your
electric scooter by simply pressing the button within 50 meters.
1
2
3
4
Unlock
Press the unlock button, and the start button stays on. The scooter enters
into the unlocked state.
Lock
When the scooter is in the static state, press the lock button, and the start
button flashes. Thescooter enters the locked state.
Remote keyless entry
After unlock the scooter,press this button twice within two(2) seconds, and
the scooter will bein the “Powered” state without key.
Search key
Press this witch within 50m,“Bi Bi” sounds searching the scooter.
How To Operate The Smart Remote Contol
1
2
43
OPERATION GUIDE
1
2
1
2
Open the small cap on the top of battery case
Align the power cord with the white arrow on the socket. Insert slowly and press firmly until
you hear a "clicking" sound.
The power plug can be pulled out by rotating the blue buckle ring counterclockwise and
pulling it up with force.
Make sure the two sets of battery capacity difference less than 20%, or it will cause the
scooter enter into lower speed condition; Single battery will cause the lower speed condition
as well.

13 14
Guide for side stand power off fuction
Handlebar is short of power, scooter notable to be started.Scooter ON position, scooter can be powered on.
USB & SIDE STAND
Guide of the USB
1. Open the dust cover of theUSB charging port;
2. Connect the cable
USB
GUIDEOF THE BREAKER
ON
ON
When the master switch is ON, the vehicle's main power source is connected.
OFF
OFF
When the master switch is OFF,the vehicle's main power source is disconnected.

15 16
BATTERY USEINSTRUCTIONS
TIPS:
Shortcircuitof the cathode and the anode at the battery'sinput.
Keep itawayfrom children, fire andheat source. It is strictly forbidden
to throw it into the fire; Violent movements, shock and extrusion are
prohibited;
Only the specified charger can be used, and other chargers are
prohibited to charge the battery;
This product has been subjected to strict inspection before leaving
factory, and it is strictly prohibited to dismantle it. Please contact our
company's after-sales department for anyquestion.
TIPS:
Do not expose the battery to water, and prevent it from being
damped by water or rained.
Charge temperature: 0-45 °C, discharge temperature: -20-45 °C;
Battery capacity will be reduced when placed in a low-temperature
environment;
Charge the battery when you use it, but make sure to charge it before
the capacity is lower than 20%. When itis not used
for a long time, please remove it from the scooter.
Pull up the battery from scooter,insert the main charger plug into the charging socket of the battery. Insert the chargers AC power plug into the home power
socket, and the battery starts charging when the charger indicator turns red.The batteryis fully charged if the chargerindicator turns from red to green.
2
BATTERY USE INSTRUCTIONS
Insertthe main charger pluginto the charging port of the scooter.
Insert the chargers AC power plug into the home power socket, and the battery starts charging when the charger indicator turns red. The battery is fully charged
if the chargerindicator turns from red to green.
How to Charge the Battery
1
1
Charging Interface
I
2
3
11
Input power terminal: connect the output charging end and plug
the input power terminal into AC supply.
Output charging end:Before charging, use the output end to
connect the battery, make sue the socket be plugged in
properbly.
Please use the special matching charger for charging, charging
time of a single set battery is normally with in 3~4h.
Input power terminal
2Output charging end
3Power indicator

17 18
Please charge the battery to half-saturation state when storing or transporting it (after the battery is discharged, charge it for 3 hours).
Place it in a dryand ventilated place;
Battery and charger should be kept in a clean,dry,and ventilated place. Keep them awayfrom corrosive materials,power source andheat source;
Storage conditions: ambient temperature -20-35 °C, humidity<65% RH;
When storing the charger, pleasedisconnect it from the battery.
Regular maintenance can enhance the service life and driving safety of the electric scooter. Please refer to the following suggestions and take care of your
scooter.
Storage, Maintenance and Transportation
BATTERY USE INSTRUCTIONS MAINTENANCE
Routine Cleaningand Maintenance
RegularInspection and Maintenance
Cleaning：Pleaseuseclean water and neutral detergent to clean it, and usesoftcloths and sponges to clean the surface;
It is prohibited to usemetal brushes, sandpaperor the like to clean it, in order not to scratch the parts surface. After cleaning,dry it with soft cloths.
TIPS:
TIPS:
Pleasedisconnect the airswitch before cleaning.
Do not use strong water jet to directly wash it, so as to avoid the defaultof mechanical parts caused bywater invasion.
Storage: try to park it in a dry and cool room to reduce the exposure to sun and rain and avoid the reduction of service life due to corrosion of parts.
When left unused for a long time, pleaseturn off theair switch and disconnect the power supply circuitto prevent over discharging.
After long-term storage, pleasefully charge itbefore use.
Thenew scooter must besubject to the first inspection and maintenance in the Service Center when it reaches 1,000 km or two months (whichever comes first).
Thescooter is recommended to besubject to regular inspection and maintenance in the Service Center at every 3,000 km or six months (whichever comes first).
Pleasedisconnect the airswitch before cleaning.
Do not use strong water jet to directly wash it, so as to avoid the fault of mechanical parts caused bybeing damped.

19 20
The scooter has no electricity,
and the READY lamp does not
shine.
When turning the speed
regulating steering handle-bar,
the motor does not turn after
being powered.
Speed is slow or mileage is
short.
Battery can notbe charged.
Battery is poorly connected.
Airswitch is not turned on.
Low battery volume.
Side stand is not retracted.
Brake handle does not reach the right position.
Steering handlebar failure.
The controller plug is loose.
Controller failure.
Low battery.
Under-inflated tire.
Heavily overloaded.
Brake pads interference.
Battery aging ornormal scrap.
Poor contactof the main plug of the charger.
Do notuse the wrongcharger.
Battery aging ornormal scrap.
Battery low-voltage protection.
Charge the battery.
Inflate thetire, and check the tire pressure before riding.
Foster a good habit, and keep the appropriate load Change
the brake pads and check the brake system before riding.
Change battery.
Check whether the main plug is in a right place Use the
special charger.
Contact of themain plugagain.
Contact with local service office of battery.
Charge the battery.
Put awaythe side stand.
Closetheparking key.
Place the brake handle at the right position.
Changehandlebar.
Re-plug controller.
Change controller.
Connect thebattery properly at its main plug.
Turn on the airswitch.
Regularmaintenance can improve the service life anddriving safety of the electric scooters.
Please refer to the fol-lowing suggestions and take care of your scooter.
Failure Causes Solutions
ELECTRICAL SCHEMATIC
Light blue
+5V
converter
K
-
pink
signal of speed handle bar
License lamp
Front turn right light
Variable speed switch
The power off braker
Speed controller
White
Power capacity indicator
Left
Left
-
Turn left instruction
Right
The negative control
12V
C
AN
1-L
C
AN
2-H
Air switch1
C
AN
2-L
The headlight switch
Max output
power120W
Rear turn left light
The charging
plug
Front headlight
485A
Brushless
controller
Reverse gear
Turn light
Meter
lighting
Right
Right
G
N
D
Anti-theft
alarm device
brake switch
P
2-
C
AN
1-G
N
D
12 V/4 W
1.5Hz
antenna
The power lock
C
AN
2-G
N
D
black
60V low voltage
Front turn left light
Y
Blue
485B
Alarm signal
Speed
indicator
Headlight
High beam instruction
Horn switch
Meter board assembly
1K
flasher
P
21-
strongpower
grey
Powerswitch
Fuse
P
22-
brown
Signal
ground
Rear turn right light
Position light / Brake
Pink
Wheel moved test
Meter cathode
Horn
+
Left
black
C
AN
1-H
Turn switch
1K
orange
250V/10A
Signal filed
Single wire
communication
HB
60V
H+-L
Turn right instruction
+5V
HC
HA
Hc
Hb
Ha
C
B
A
PowerSwitching Box
Power consumption signal
Battery 1K
Signal
Battery 1K
Signal
Lights change
Normal
status