Webasto Hollandia 700-II Series User manual

Webasto Product N.A., Inc. • 15083 North Road • Fenton, Michigan 48430 Page 1
For Technical Assistance in USA Call: [phone] • In Canada Call: [phone]
Visit us on the Web at: www.webasto.us
Product Information
Sunroof models
All Hollandia 700-II sunroofs (Entry and Comfort)
Preparation
•Connect to a power supply and perform basic push and hold operation during the bench test to verify
mechanical functionality.
•The 700-II comfort level series sunroof does not come pre-initialized; the initialization procedure below
must be performed after the unit has been installed into the vehicle.
Initialization Procedure
After the sunroof unit has been installed into the vehicle, connect the wiring to the sunroof control unit (SCU),
power supply and switch.
Note: First connect the power supply with the SCU then connect the switch.
Now the sunroof unit must be initialized.
Warning:
During initialization jamming protection is inoperable. Therefore, use extreme caution while
performing this procedure.
H700 Comfort
•Start the initialization procedure with the glass panel in the
full closed position.
•Confirm the vehicle is in PARK and start the engine to assure
voltage is above 11 (volts) during initialization.
•Press button (close) continuously.
After approx. 10 sec. the glass panel will:
omove towards the FULL TILT position
ostay in FULL TILT position for approx. 2 sec.
omove towards FULL SLIDE OPEN position
omove towards FULL CLOSED position
omove towards FULL SLIDE OPEN position
omove towards the FULL TILT position
omove towards FULL CLOSED position.
•Release button (close).
The sunroof system is now initialized.
•If the initialization is not successful, check if the sunroof
installation is done correctly.
Turn the ignition key to “OFF” and back to the “RUN”
position and try again.
Category: Sunroof
Document Number: PI063BC
Description: Hollandia 700-II Initialization and Resetting
Date: 10/28/2011

Webasto Product N.A., Inc. • 15083 North Road • Fenton, Michigan 48430 Page 2
For Technical Assistance in USA Call: [phone] • In Canada Call: [phone]
Visit us on the Web at: www.webasto.us
Product Information
H700 Entry
•Start the initialization procedure with the glass panel in full closed position.
•Turn the ignition key to the “RUN” position (ideally a running vehicle engine to obtain maximum battery
voltage)
•Press button (close) continuously.
After approx. 10 sec. the glass panel will
omove towards the FULL TILT position
omove towards FULL CLOSED position.
•Release button (close).
The sunroof system is now initialized.
•If the initialization is not successful, check if the sunroof installation is done correctly.
Turn the ignition key to “OFF” and back to the “RUN” position and try again.
Resetting
Once the initialization procedure has been performed there are certain conditions where the sunroof must be
reset. (e.g. after sunroof failure, replacing the battery, car accident). Follow the reset procedure below:
H700 Comfort
•Start the reset procedure with the glass panel in full closed position.
•Turn the ignition key to “OFF” for 30 seconds then back to the “RUN” position (ideally a running vehicle
engine to obtain maximum battery voltage).
•Within one minute press button (close) continuously.
After approx. 10 sec. the glass panel will
omove towards the FULL TILT position
ostay in FULL TILT position for approx. 2 sec.
omove towards FULL SLIDE OPEN position
omove towards FULL CLOSED position
omove towards FULL SLIDE OPEN position
omove towards the FULL TILT position
omove towards FULL CLOSED position.
•Release button (close).
The sunroof system has now been reset.
H700 Entry
•Start the reset procedure with the glass panel in full closed position.
•Turn the ignition key to “OFF” for 30 seconds then back to the “RUN” position (ideally a running vehicle
engine to obtain maximum battery voltage).
•Press button (close) continuously.
After approx. 10 sec. the glass panel will
•move towards the FULL TILT position
•move towards FULL CLOSED position.
•Release button (close).
Now the sunroof system has been reset.
If you have any questions, contact our technical support team at [phone] or via email at:
[e-mail].