Weber MONSTER AMALFI STUDIO EASEL Manual

MAKE SURE CARTON CONTAINS THE FOLLOWING PARTS
WOOD PARTS
ytitnauQ ........ Description ID#
2 ea......... Base Feet [1]
2 ea......... Base Cross Members [2]
2 ea......... Uprights [3]
1 ea......... Channelled Center Column [4]
1 ea. ....... Material Tray [5]
2 ea......... Channelled Side Columns [6]
1 ea......... Ratchet Column [7]
1 ea......... Lower Cross Member [8]
1 ea......... Upper Cross Member [9]
2 ea......... Extendable Rear Legs [10 & 11]
1 ea......... Adjustable Center Column [12]
1 ea......... Upper Canvas Support [13]
HARDWARE PARTS
ytitnauQ ........ Description ID#
4 ea. .. Bolts & Cams: 6 X 60mm [A]
.ae61 . Screws: 4 X 16mm [B]
2 ea. .. Bolts & Cams: 6 X 60mm [C]
4 ea. .Screws: 4 X 25mm [D]
1 ea. .. Loop Mechanism & [4] Screws [E]
4 ea. .. Bolts & Cams: 6 X 60mm [F]
2 ea. .. 6 X 70mm Bolt/Knob/Washer&Wood Washer [G]
2 ea. .. 6 X 45mm Bolt/Knob & Washers [H3]
2 ea. .. 6 X 40mm Bolt/Knob & Washers [H4]
2 ea. .. 6 X 120mm Bolt/Knob & Washers [H5]
3 ea. .. Knobs: 2 same size one longer
4 ea. .. Castors: 2 locking, 2 not locking
TOOLS INCLUDED
ytitnauQ ........ Description
1 ea......... Flathead Screwdriver - Red Handle
1 ea......... Phillips Head Screwdriver - Orange Handle
Page 1
4 X 25mm
Screws (4 each)
[D]
6 X 60mm
Bolt & Cams
(4 each)
[A]
6 X 70mm Bolts, Knobs, Washers
& Wood Washers (2 of each)
[G]
92-3010 • MONSTER AMALFI STUDIO EASEL
ASSEMBLY/SET-UP INSTRUCTIONS
[4] Floor Castors (2 Locking)
4 X 16mm
Srews for Castors
(16 each)
[B]
6 X 60mm
Bolt & Cams
(2 each)
[C]
3 X 12mm
Screws * Loop Mechanism
[E]
6 X 60mm
Bolt & Cams
(4 each)
[F]
6 X 45mm
Bolts, Knobs & Washers
(2 each)
[H3]
6 X 40mm
Bolts, Knobs & Washers
(2 each)
[H4]
6 X 120mm
Bolt/Knob & Washers
[H5]
3 Knobs
2 same size one longer
[unmarked]
Base Feet [1]
Side View
Top View
Base Cross Members
[2]
Uprights [3]
Channelled Center Column [4]
Material Tray [5]
Channelled Sides [6]
Ratchet Column [7]
Lower Cross Member [8] Upper Cross Member [9]
Extendable Rear Legs [10 & 11]
Adjustable Center Column [12]
Upper Canvas Support [13]
03/2015

STEP 1. Attach the [4] castors to
the two base feet (1) making sure
the 2 locking castors are
positioned in the rear. NOTE:
the rear of the base has the hole
nearest that castor position.
Secure with four screws (B)
per castor.
See FIG 1.
IMPORTANT - READ ALL INSTRUCTIONS BEFORE ASSEMBLING EASEL and USE 2 PEOPLE WHEN ASSEMBLING!
Page 2
STEP 4. Turn your base assmebly over onto the
castors and you should now have a base that is
assembled like FIG 4.
FIG 1
1
FIG 5
Rear of the base
with hole.
FIG 2
STEP 3. Secure Base Cross Members to base using
the four 6 X 60mm Bolts and Cams (A). Insert Cam into
hole found in Base Cross Member and insert bolt into
base foot. Tighten by holding Cam in position while
tightening down bolt with phillips screwdriver. See FIG 3.
STEP 2. Attach the two Base Cross members (2) to the
base feet (1) By inserting the oval male end of the Base
Cross member into the oval female cut-out of the base
foot. See Fig 2. NOTE: The hole in the cross member
should be up, since the base is upside down.
Repeat with
second cross
member.
FIG 3
Cam
Phillips
Screwdriver
FIG 4
1
2
1
2
1
2
1
2
STEP 5. This next step involves attaching the uprights
(3) to the base assembly. You will find two oval holes on
the top side of the assembled base, these oval holes
are for the oval male ends of the uprights (3) to go into.
Secure with two 6 x 60mm bolts and cams (C).
Insert Cam
here and
morftlobnethgit
bottom of Base
with phillips
screwdriver
6 X 600 mm
bolt here
3
1
After proper
assembly, base
with uprights
should look like
this.
3
3
1
1
2
2
03/2015

Page 3
FIG 8c
STEP 6. Attach Material Tray (5) to Channelled Center
Column (4) using four 4 X 25mm Screws (D).
See FIG 6a & FIG 6b.
STEP 8a. Assembling the H-Frame. This step involves
assembling parts (6, 7, 8 & 9) to form the H-Frame
portion of the easel. Begin by taking the channelled
sides (6) & the upper cross member (9) and inserting
the oval male ends of the upper cross member into the
oval holes of the channelled sides. See FIG 8a.
Secure this step using two 6 X 60mm bolts and Cams
as previously described in earlier steps. (as in Step 3)
5
FIG 6a
FIG 6b
STEP 7. Attach Loop Mechanism (E) to Material Tray
(5) using the four 3 X 12mm screws. Secure with
Phillips Screwdriver (provided) See FIG 7.
NOTE: Make sure the Loop Mechanism is in the
proper position as shown in FIG 7. This will allow
for proper adjustments when moving the material
tray up or down the Ratchet Column.
FIG 7
4
5
4
5
4
E
6
9
6
FIG 8a
Make sure the Ratchet column
is positioned so that the metal
part that is closest to one end
of the column is the bottom
end. See FIG 8c.
NOTE: This column is secure
once the bottom portion of
the H-Frame is assembled.
NOTE: This image
is the rear side of
the H-Frame. The
metal portion of
the ratchet
column is on the
reverse side. Not
visable in this
photo.
FIG 8b
Bottom End
of Ratchet
Column
connects with
lower cross
member (8)
Top Portion of
Ratchet
Column
connects with
upper cross
member (9)
STEP 8b. Continue by
inserting the ratchet
column (7) up into the
oval hole of the upper
cross member (9).
9
7
7
03/2015
03/2015

STEP 10. Finish assembling the H-Frame by attaching
the lower cross member (8) to the ratchet column (7) by
inserting the ratchet column down into the oval hole of
the lower cross member. Secure by fitting the lower cross
member into the oval holes of the channelled sides (6).
See FIG 10. Secure this step, using two 6 X 60mm bolts
and Cams as previously described in earlier steps.
(as in Step 3)
STEP 12. Attach assembled H-Frame to easel uprights
found on assembled base. Make sure the metal ratchet
front is facing out towards the front of the easel.
This step involves securing the H-Frame assembly to the
uprights of the easel base as shown in FIG 12.
FIG 10
STEP 11. Your assembled H-Frame should look like
FIG 11.
NOTE: This is the front view of the assembled
H-Frame
FIG 11
7
6
6
8
7
6
6
8
9
Page 4
FIG 12
STEP 13. To secure the H-Frame to the uprights, have
one person hold the H-frame while the other inserts one
part (G) 6 X 70mm Bolt through the inside edge of the
channelled sides and though the other side, then attach
one wood washer to the bolt
end. See FIG 13a.
Continue through the
upright and secure with
metal washer and black knob.
See FIG 13b.
REPEAT with other side
of H-Frame to
complete this Step.
FIG 13a
FIG 13b
7
6
8
3
6
3
6
3
The completed
assembly should look
like FIG 13b.
03/2015

Page 5
STEP 14. Attach Extendable Rear Legs (10&11) to base
(1) and upper portion of Channelled Sides (6).
Attach the wider end of the adjustable Rear legs (10) to
11
6
FIG 14bFIG 14a
FIG 15
H3
H3
STEP 15. Attach upper portion of Extendable Rear Legs
(11) to upper portion of Channelled Sides (6).
Pull-out the narrower end of the extendable leg (11) and
attach it to the inside edge of the channelled sides by
inserting one 6 X 45mm bolt (H3) through the outside side
of the channelled side continuing through the extendable
leg (11) and then placing the metal washer over the bolt
and tightening with the knob to secure. See FIG 15.
See FIG 15b for proper view of assembly step 15.
FIG 15b
6
6
11
11
7
9
STEP 16. Attach 6 X 40mm Bolts, knobs & washers (H4)
to Extendable legs (10 & 11). These adjustment knobs
are used along with the others to lower the easel into a
horizontal position. Insert the bolt through the inside edge
of the extendable
leg (11), continue
going though to the
other side and
complete with metal
washer and knob.
Tighten to secure.
See FIG 16.
FIG 16
STEP 17. Loosen all knobs to lower the easel into the
horizontal position. Once in flat position, tighten all knobs
to secure. See FIG 17. This step involves inserting and
sliding the Channelled Center Column (4) and Material
tray (5) assembly through the upper cross member (indi-
cated by the circle) and guiding the material tray corners
into the channelled Sides (indicated by the squares). See
FIG 17. See inset photos below for detail.
FIG 17
03/2015
the base by inserting one 6x120 mm Bolt [H5], see Fig 14ab.
Continue through the upright and secure with metal
wahser and black knob.Repeat with other Extendable Leg.

• Made in China
Martin/F. Weber Co.
4444 Lawton St., Detroit, MI 48208 USA
Tel:[phone] • Fax:[phone]
E-mail:[email protected]
www.MartinUniversalDesign.com • www.weberart.com
Created NOV07RPI
IMPORTANT
If you have difficulty assembling your 92-3010 Weber Monster
Amalfi Studio Easel or need customer service assistance.
Please call: Martin Universal Design, Inc. Customer Service Hot
Line at 1-313-895-0700. If you need additional parts,
it is not necessary to contact your dealer, our Customer Service
Rep. will forward them to you immediately.
Page 6
STEP 18. Once Channelled Center Column is in its
proper location in the upper Cross Support, secure with
the longest of the three remaining knobs by threading the
threads of the knob in the hole in the rear of the cross
support. Tighten to secure. See FIG 18.
STEP 20. Final step involved in the assembly of your
New 92-3010 Easel.
Attach the Upper Canvas Support (13) to the Adjustable
Center Column (12) by sliding the grooves of the canvas
support down into the channels of the Adjustable Center
Column. Do this from the top end of the Adjustable
Center Column. Secure with remain knob. tighten to
secure at desired position. See FIG 20
FIG 18
STEP 19. This step involves adding the Adjustable
Center Column (12) down into the Channelled Center
Column (4). See FIG 19. To secure into place, thread one
of the remaining two shorter knobs into the hole found on
the rear of the Channelled Center Column. See FIG 19b.
FIG 19
FIG 19b
Rear view of
Channelled Center
Column where knob
is to be threaded.
4
9
13
7
12
4
12
4
FIG 20
ADJ 1. Adjusting Height Material Tray.
Insert finger in locking loop pin below Material Tray and
pull outward. This will cause the material tray support to
release from the metal ratchet column allowing you to
raise or lower the material tray and center column.
PLEASE NOTE: Be careful when raising the
material tray, that you are aware that the top of the
column will not interfere with ceiling or any other
object in rooms that have low ceilings.
03/2015

92-3010
Weber Monster Amalfi Studio Easel
Height Adjustable Center Column/Material Tray
by pulling loop out from ratchet system
Ratchet Cloumn (7)
Extendable Rear legs (11)
Adjustable Center Column (12)
Upper Canvas Support (13)
Adjustable Material Tray (5)
Upper Cross Member (9)
Uprights (3)
Lower Cross Member (8)
Page 7
• Made in China
Created NOV07 RPI
Extendable Rear legs (10)
Base Foot (1)
Base Cross Support (2)
Locking Castor
03/2015
Martin/F. Weber Co.
4444 Lawton St., Detroit, MI 48208 USA
Tel:[phone] • Fax:[phone]
E-mail:[email protected]
www.MartinUniversalDesign.com • www.weberart.com