Weber Flame iQ User manual

WWW.WEBER.COM 1
OWNER’S GUIDE
TM
FOR USE WITH UNIVERSAL LIQUEFIED PETROLEUM GAS (ULPG / LPG) ONLY
SUITABLE FOR THE BABY Q SERIES - Q1000 AND Q1200 MODELS ONLY
SCAN FOR ASSEMBLY
AND HOW TO USE
INSTRUCTIONS
Thank you for purchasing the WEBER Flame iQ Accessory for your WEBER Baby Q.
Take a few minutes to read the manual.
Congratulations on the purchase of your WEBER Flame iQ
with patented technology.
The Flame iQ requires a 12 V or 240 V power supply. The
Flame iQ comes with a 2.4 metre 12 V power cable and a
1 metre 240/12 V power cable. This electrical connection
provides the Flame iQ with the ability to continually sense for
a flame.
WHAT IS THE WEBER Flame iQ?
The Flame iQ is a type of flame safeguard device, with added
features and benefits.
A flame safeguard device is designed to stop the flow of gas
to an appliance in the case that the gas flame goes out – for
example, if the flame is blown out in windy conditions.
The Flame iQ has the added functionality of continuously
sensing for a flame. It will attempt to reignite the burner in
the event of a ‘flame out’ (up to 3 attempts), before shutting
off the gas and going into a lockout mode. If the burner
reignites, the Flame iQ will reset for another 3 attempts.
HOW DOES THE WEBER Flame IQ WORK?
The Flame iQ features a sensing probe, situated on the
burner. If the probe senses a ‘flame out’, it sends a signal to
the Flame iQ, which then attempts to reignite the burner, up
to 3 times at 5 second intervals.
If the burner is not reignited by the third relighting attempt,
it will shut off the gas to the burner and go into lockout
mode. This is shown on the Flame iQ when the reset light is
illuminated (refer to lighting instructions on page 7).
If the burner is successfully reignited on the first, second or
third attempt, the Flame iQ resets itself (and will attempt 3
reignitions if the probe again senses a ‘flame out’).
ADDITIONAL BENEFITS OF USING THE WEBER Flame iQ
WITH YOUR WEBER Baby Q
• The Flame iQ meets the requirements of the Australian
& New Zealand Standard for Outdoor Gas Appliances
for barbecues connected to the piping on a caravan or
boat. Once your Baby Q is fitted with a Flame iQ, it can
be connected to the plumbed gas supply of a boat or
caravan.
• Should the flame in your Baby Q blow out due to strong
winds, the Flame iQ will sense a ‘flame out’ and attempt
to re-ignite the burner. This will be seamless and happen
continuously whenever the flame is blown out (if the
burner is reignited within 3 attempts at each ‘flame out’).
Your food will still be cooked through perfectly.
• When the Flame iQ is turned on, it runs a self-check to
ensure that there is no flame present on the burner. If
there is a flame present the Flame iQ will go into reset
mode. This ensures that the Flame iQ is in the correct
safe start position with no gas flowing through the Flame
iQ.
• Easy-to-see indicator lights on the Flame iQ control
panel mean you don’t have to lift the lid of your barbecue
to see if it’s alight.
The lights indicate:
a) Green light illuminated - Flame iQ is ready to operate.
b) Blue light illuminated - flame detected at burner.
c) Blue light off - flame out detected and reignition being
attempted.
d) Red light illuminated - lockout mode due to
unsuccessful reignition.
• A pre-set maximum run time of 8 hours is built into the
Flame iQ, meaning that if you forget to turn your Baby Q
off after use, it will automatically cut the gas supply to
the barbecue after 8 hours of continuous run time.

WWW.WEBER.COM 2
DANGER DANGER
Failure to follow the DANGERS, WARNINGS
and CAUTIONS contained in this Owner’s
Guide may result in serious bodily injury
or death, or may result in a fire or an
explosion causing damage to property.
For additional information please refer to
the WEBER barbecue owner’s guide for the
Q1000 and Q1200.
The Flame iQ needs to be plugged into a
12 V or 240 V power supply.
DANGERS
WARNINGS
THIS GAS ACCESSORY IS DESIGNED
FOR OUTDOOR USE ONLY.
DANGER
1)
2)
3)
4)
Shut off gas to the appliance.
Extinguish any open flames.
Open lid.
If odour continues, keep away from
the appliance and immediately
call your gas supplier or your fire
department.
Failure to follow these instructions could
result in fire or explosion which could
cause property damage, personal injury
or death.
If you smell gas:
1)
2)
3)
4)
Never operate the Baby Q with Flame
iQ unattended.
Never operate Baby Q with Flame iQ
within 610 mm (2 ft) of any structure,
combustible material or other gas
cylinder.
Never operate Baby Q with Flame iQ
within 7.5 m (25 ft) of any flammable
liquid.
If a fire should occur, turn off your gas
bottle, keep away and immediately call
your fire department. Do not attempt
to extinguish an oil or grease fire with
water.
Failure to follow these instructions could
result in fire, explosion or burn hazard,
which could cause property damage,
personal injury or death.
This instruction manual contains important information necessary for the proper assembly and safe use of the Weber
Flame iQ. Read and follow all warnings and instructions before tting and using the Flame iQ accessory. Keep this manual
for future reference. Carefully follow all leak-check procedures in this Owner’s Guide. Do not use the Flame iQ without
rst reading the burner ignition sections in this manual.
Do not use the WEBER Flame iQ unless
all parts are in place. The accessory
must be properly assembled according
to the assembly instructions.
Your WEBER Flame iQ should never be
used by children. Accessible parts of
the accessory may be very hot. Keep
young children and pets away while
accessory is in use.
This WEBER Flame iQ is not intended
for commercial use.
Do not attempt to disconnect the gas
regulator and hose assembly or any
gas tting while your Flame iQ is in
operation.
Use heat-resistant barbecue mitts or
gloves, whilst cooking on the barbecue.
After a period of storage and/or
nonuse, the WEBER Flame iQ should be
checked for gas leaks. See instructions
in this Owner’s Guide for correct
procedures.
Do not operate the WEBER Flame iQ if
there is a gas leak present.
Do not use a ame to check for gas
leaks.
Universal liqueed petroleum gas
(ULPG / LPG) is not natural gas. The
conversion or attempted use of natural
gas in a universal liqueed petroleum
gas unit or universal liqueed
petroleum gas in a natural gas unit is
dangerous and will void your warranty.
Keep any electrical supply cord and the
fuel supply hose away from any heated
surfaces.
The Flame iQ should be cleaned on a
regular basis.
If you see, smell or hear the hiss of
gas escaping from the rellable LPG
cylinder:
1. Move away from rellable LPG
cylinder.
2. Do not attempt to correct the
problem yourself.
3. Call your re department.
A dented or rusty LPG cylinder may be
hazardous and should be checked by
your LPG supplier. Do not use a LPG
cylinder with a damaged valve.
Although your LPG cylinder may
appear to be empty, gas may still be
present, and the LPG cylinder should
be transported and stored accordingly.
The use of alcohol, prescription drugs,
non-prescription drugs, or illegal
drugs may impair the consumer’s
ability to properly and safely assemble,
move, store or operate the WEBER
Flame iQ.

WWW.WEBER.COM 3
TABLE OF CONTENTS
DANGERS & WARNINGS........................... 2
WARRANTY.............................................. 3
PARTS LIST.............................................. 4
ASSEMBLY............................................. 4-5
LEAK CHECK............................................ 6
BURNER IGNITION & USAGE..................... 7
TROUBLESHOOTING................................. 8
The accessory illustrated in this Owner’s Guide may vary
slightly from the model purchased.
WARRANTY
PRODUCT WARRANTY PERIOD
DISCLAIMERS
WEBER MAKES NO IMPLIED WARRANTIES INCLUDING WITHOUT
LIMITATION ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE, OTHER THAN WHAT IS
EXPRESSLY MADE IN THIS LIMITED WARRANTY. NO WARRANTIES
SHALL APPLY AFTER THE APPLICABLE PERIODS OF THIS LIMITED
WARRANTY. NO OTHER WARRANTIES GIVEN BY ANY PERSON OR
ENTITY, INCLUDING A DEALER OR RETAILER WITH RESPECT
TO ANY PRODUCT (SUCH AS ANY “EXTENDED WARRANTIES”),
SHALL BIND WEBER. THE EXCLUSIVE REMEDY OF THIS LIMITED
WARRANTY IS REPAIR OR REPLACEMENT OF THE PART OR
PRODUCT. THE TERMS OF THIS LIMITED WARRANTY PROVIDE
THE SOLE AND EXCLUSIVE REMEDY ARISING FROM THE SALE OF
THE PRODUCTS COVERED HEREBY. WEBER SHALL NOT BE LIABLE
FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL
LOSS OR DAMAGES. SOME JURISDICTIONS DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES, OR LIMITATIONS ON HOW LONG AN IMPLIED
WARRANTY LASTS, SO THE ABOVE EXCLUSIONS OR LIMITATIONS
MAY NOT APPLY TO YOU.
IN NO EVENT SHALL RECOVERY OF ANY KIND BE GREATER THAN
THE AMOUNT OF THE PURCHASE PRICE OF THE WEBER PRODUCT
SOLD.
YOU ASSUME THE RISK AND LIABILITY FOR LOSS, DAMAGE, OR
INJURY TO YOU AND YOUR PROPERTY AND/OR TO OTHERS AND
THEIR PROPERTY ARISING OUT OF THE MISUSE OR ABUSE OF THE
PRODUCT OR FAILURE TO FOLLOW INSTRUCTIONS PROVIDED BY
WEBER IN THE ACCOMPANYING OWNER’S GUIDE.
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS,
AND YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY IN
DIFFERENT JURISDICTIONS.
PARTS AND ACCESSORIES REPLACED UNDER THIS LIMITED
WARRANTY ARE WARRANTED ONLY FOR THE BALANCE OF THE
ORIGINAL WARRANTY PERIOD(S).
THIS LIMITED WARRANTY APPLIES TO PRIVATE SINGLE FAMILY
HOME OR APARTMENT USE ONLY AND DOES NOT APPLY TO
WEBER BARBECUES USED IN COMMERCIAL, COMMUNAL OR
MULTI-UNIT SETTINGS SUCH AS RESTAURANTS, HOTELS,
RESORTS OR RENTAL PROPERTIES.
WEBER MAY FROM TIME TO TIME CHANGE THE DESIGN OF ITS
PRODUCTS. NOTHING CONTAINED IN THIS LIMITED WARRANTY
SHALL BE CONSTRUED AS OBLIGATING WEBER TO INCORPORATE
SUCH DESIGN CHANGES INTO PREVIOUSLY MANUFACTURED
PRODUCTS, NOR SHALL SUCH CHANGES BE CONSTRUED AS AN
ADMISSION THAT PREVIOUS DESIGNS WERE DEFECTIVE.
WEBER’S RESPONSIBILITIES
WEBER provides, to the original purchaser of the WEBER product (or
in the case of a gift or promotional situation, the person for whom
it was purchased as a gift or promotional item), that the WEBER
product is free from defects in material and workmanship for the
period(s) of time specied below when assembled and operated
in accordance with the accompanying Owner’s Guide. (Note: If you
lose or misplace your WEBER Owner’s Guide, a replacement is
available online at www.weber.com). Under normal, private single
family home or apartment use and maintenance, WEBER agrees to
repair or replace defective parts within the applicable time periods,
limitations and exclusions listed below. THIS LIMITED WARRANTY
IS EXTENDED ONLY TO THE ORIGINAL PURCHASER AND IS NOT
TRANSFERABLE TO SUBSEQUENT OWNERS, EXCEPT IN THE CASE
OF GIFTS AND PROMOTIONAL ITEMS AS NOTED ABOVE.
Our goods come with guarantees that cannot be excluded under
the Australian Consumer Law. You are entitled to a replacement
or refund for a major failure and for compensation for any other
reasonably foreseeable loss or damage. You are also entitled
to have the goods repaired or replaced if the goods fail to be of
acceptable quality and the failure does not amount to a major
failure.
The benets given under this Limited Warranty are in addition to
other rights and remedies you have under the Australian Consumer
Law in relation to this WEBER gas barbecue.
OWNER’S RESPONSIBILITIES
To ensure trouble-free warranty coverage, please retain your
original sales receipt and/or invoice.
The Owner must take reasonable care of the WEBER product
and follow all assembly instructions, usage instructions and
preventative maintenance as outlined in the accompanying
Owner’s Guide. If you live in a coastal area, or have your
product located near a pool, maintenance includes regular
washing and rinsing of the exterior surfaces. If you believe
that you have a part that is covered by this Limited Warranty,
please contact the WEBER Customer Service Representative
in your area using the contact information on our web site.
WEBER will, upon investigation, repair or replace (at its option)
a defective part covered by this Limited Warranty. In the event
that repair or replacement are not possible, WEBER may chose
(at its option) to replace the accessory in question with a new
accessory of equal or greater value. WEBER may ask you to
return parts for inspection, shipping charges to be pre-paid.
This LIMITED WARRANTY does not cover damage, deterioration,
discoloration and/or rust caused by:
• Abuse, misuse, alteration, modification, misapplication,
vandalism, neglect, improper assembly or installation,
and failure to properly perform normal and routine
maintenance;
• Insects (such as spiders) and rodents (such as squirrels),
including but not limited to damage to burner tubes and/
or gas hoses;
• Exposure to salt air and/or chlorine sources such as
swimming pools and hot tubs/spas;
• Severe weather conditions such as hail, hurricanes,
earthquakes, tsunamis or surges, tornadoes or severe
storms.
The use and/or installation of parts on your WEBER product
that are not genuine WEBER parts will void this Limited
Warranty, and any damages that result are not covered by this
Limited Warranty.
Any conversion of a gas barbecue not authorized by WEBER and
performed by a WEBER authorized service technician will void
this Limited Warranty.
Weber-Stephen Products (Aust) Pty Ltd.
Level 1, 142-144 Fullarton Road
Rose Park, SA 5067 AUSTRALIA
1300 301 290 (toll free)
Weber-Stephen Products New Zealand.
86 East Highbrook Drive
East Tamaki, Auckland 2013 NEW ZEALAND
0800 493 237 (toll free)
Flame iQ: 3 years
Thank you for purchasing a WEBER product.
Weber-Stephen Products (Aust) Pty Ltd and
Weber-Stephen Products New Zealand (“WEBER”)
prides themselves on delivering a safe, durable and
reliable product.
This is WEBER’s Limited Warranty provided to you
at no extra charge. It contains the information you
will need to have your WEBER product repaired in
the unlikely event of a failure or defect.

WWW.WEBER.COM 4
PARTS LIST & ASSEMBLY
1. Prior to commencement of fitting the
Flame iQ to your barbecue, ensure the
barbecue is clean of any cooking debris
(existing barbecue). If recently used,
ensure the barbecue has cooled before
attempting to fit the Flame iQ.
2. Ensure the gas cylinder is not connected
to the barbecue. If connected, disconnect
the hose/regulator assembly from the LPG
cylinder.
3. Disconnect the hose and regulator
assembly from the barbecue. Using the
supplied 5/8” and 3/4” spanners, unscrew
the hose fitting from the manifold inlet
fitting. Be careful not to damage the
connections.
INSTRUCTIONS APPLICABLE TO MODELS Q1000, Q1200
PARTS LIST
4. Remove the barbecue lid by removing the
hinge pins and clips.
5. Remove the barbecue grills to enable
access to the burner.
KEEP THIS SPANNER
STATIONARY
6. Remove the hose guide/retaining ring
from the rear frame leg. Lay the barbecue
on it’s back for ease of access and remove
the mounting screws using the supplied
1/4” spanner. Be careful to retain the
screws as these are required to remount
the Flame iQ. The hose guide/retaining
ring is not reused and can be recycled.
7. Mount the Flame iQ attachment bracket
in position, using the supplied 1/4”
spanner. Use the screws and mounting
points previously used for the hose guide/
retaining ring.
8. Sit the barbecue back on its feet. Remove
the screw securing the burner using a
flat head screwdriver. Rotate the burner
tube towards you into a vertical position
and slide to the left to disengage from the
manifold/valve.
9. Place the Flame iQ underneath the handle
and behind the manifold/valve (ensure
the Flame iQ is on the outside of the
attachment bracket). Loosely connect by
hand tightening the outlet gas connection
on the Flame iQ to the manifold inlet
fitting. Do not over-tighten.
1. Flame iQ control box
2. Attachment bracket
3. Flame iQ 12 V 2.4 metre
power cable
4. 240/12 V power socket
& 1.0 metre cable.
5. 2 x screws [M4 8mm]
7. Safeguard sticker
1.
2.
3.
4.
5.
6.
7.
1 x Phillips Head Screwdriver
1 x Flat Head Screwdriver
INCLUDED with your Flame iQ:
NOT INCLUDED:
6. Spanners
1/4” 3/4” and 5/8” 3/4”

WWW.WEBER.COM 5
10. Secure the Flame iQ to the attachment
bracket with the 2 screws using a phillips
head screwdriver.
11. Feed the sensor probe through the
burner clearance hole in the side of the
barbecue cook box. Pass the sensor front
legs through first, then swing the sensor
through the clearance hole
ASSEMBLY
INSTRUCTIONS APPLICABLE TO MODELS Q1000, Q1200
1
2
12. Reinstall the burner to where it is in a vertical
position, but not attached to the manifold/
valve.
13. Clip the sensor probe into position on the
burner. Ensure the sensor probe clips into
position on the burner by hooking under
the front leg over the flat section of the
burner tube (1) and then push the back
legs down onto the burner tube (2).
14. Slide the burner tube to the right over the
manifold/valve ensuring that the wires are
not pinched or twisted around the burner
tube. Rotate the burner tube back to a
horizontal plane ensuring it is locked onto
the manifold/valve and refit the burner
tube with securing screw.
15. Screw the hose and regulator assembly
to the inlet of the Flame iQ using the 3/4”
spanners. Ensure you only tighten the
nut on the hose. Do not tighten the nut on
the Flame iQ housing. Reconnect the gas
cylinder.
16. Using the 5/8” and 3/4” spanners
provided, tighten the outlet gas
connection on the Flame iQ to the
manifold/valve inlet fitting (previously
finger tightened in step 9).
17. Open the power supply weather cover.
Connect the power cable.
18. Place the ‘Flame safeguard fitted’ label
on the data label to be found on the back
leg of the barbecue. Do not obscure the
serial number.
19. Conduct a leak check of all gas fittings,
including with the Flame iQ powered
up and activated (on – green light
illuminated) but barbecue gas control
knob off. Refer to page 6 to perform a
leak test.
WARNING: needs to be plugged into a 12 V or 240 V
power supply.
20. If no leaks are detected, refer to Flame
iQ operating instructions and check
functionality of Flame iQ.
21. After checking operation, refit cooking
grills and lid. Your barbecue is now
ready to use, incorporating the Flame iQ.
KEEP THIS SPANNER
STATIONARY
KEEP THIS
SPANNER
STATIONARY

WWW.WEBER.COM 6
PREPARING TO USE YOUR Flame iQ
WHAT IS A LEAK CHECK?
The fuel system in your WEBER
barbecue fitted with Flame iQ
features connections and fittings. A
leak check is a reliable way to make
sure that no gas is escaping from any
of the connections or fittings.
Although all factory-made
connections have been thoroughly
checked for gas leaks, it’s important
to perform a leak check before using
your Flame iQ for the first time, as
well as anytime you disconnect and
reconnect a fitting and each time you
perform routine maintenance.
NOTE: All factory-made connections have been
thoroughly checked for gas leaks and the burner has
been ame-tested. As a safety precaution, however,
you should check all ttings for leaks before using
your WEBER gas barbecue. Shipping and handling may
loosen or damage a gas tting.
You will need: A spray bottle, brush or rag and a soap
and water solution. (You can make your own soap and
water solution by mixing 20% liquid soap with 80%
water; or, you can usually nd leak check solution in the
plumbing section of a hardware store.)
When leak checking is complete, turn gas supply off
at the source and rinse connections with water.
a) Regulator-to-LPG cylinder connection (4).
b) Regulator hose-to-regulator connection (5).
c) Flame iQ to regulator hose connection (6).
d) Flame iQ to valve connection (7).
Make sure the burner control knob is turned off by
pushing it in and turning it clockwise to the OFF (O)
position (1).
A)
Turn gas supply on at source (2).B)
Plug Flame iQ to power source (3A) and press the
ON button (3B).
C)
To check for leaks, wet ttings with the soap and
water solution, using a spray bottle, brush or rag. If
bubbles form, or if a bubble grows, there is a leak.
Apply the soap and water solution to the following
connections:
D)
E)
NOTE: Since some leak test solutions, including soap and water, may be
slightly corrosive, all connections should be rinsed with water after checking
for leaks.
WARNING: The gas connections of your gas
barbecue have been factory tested. We do,
however, recommend that you leak check
all gas connections before operating your
gas barbecue.
WARNING: Perform these leak checks
even if your barbecue was dealer or store
assembled.
WARNING: You should check for gas leaks
every time you disconnect and reconnect a
gas tting.
WARNING: Do not ignite burner when leak checking.
WARNING: If there is a leak at connection (4,5,6 or 7)
turn off the gas. DO NOT OPERATE THE BARBECUE.
Contact the Customer Service Representative in
your area using the contact information on our
website. Log onto www.weber.com.
Sparks or open ames will result in a re or
explosion, which can cause serious bodily injury
or death and damage to property.
CHECKING FOR GAS LEAKS

WWW.WEBER.COM 7
16 WWW.WEBER.COM
BURNER IGNITION & USAGE
Summary lighting instructions are on the
instruction tag (Q 1000, Q 1200) or the right
fold-out table (Q 2000, Q2200).
METHODS OF BURNER
IGNITION
There are two ways to ignite
the burner. The first is by using
the ignition system built into
your barbecue. The second is
with a match.
Next are the steps for
igniting your barbecue using
the ignition system. On the
following page are steps for
igniting your barbecue with a
match.
BURNER IGNITION
A) Open the barbecue lid (1).
m DANGER
Failure to open the lid before igniting the
barbecue’s burner, or not waiting five
minutes to allow the gas to clear if the
barbecue does not light, may result in an
explosive flare-up which can cause serious
bodily injury or death.
B) Unfold the side tables(2) (Q 2000™, Q 2200™).
C) Make sure the burner control knob is turned to the o
() position(3). Check by pushing burner control knob
in and turning it clockwise until it stops.
D) Turn gas supply on at source.
E) Push burner control knob in and turn it
counterclockwise to start/high ( ) position (4).
F1) Push the red igniter button several times, so it clicks
each time (5) (Q 1000™, Q 2000™).
OR
F2) Push and hold in the electronic igniter button (6)
(Q 1200™, Q 2200™). You will hear the igniter clicking.
G) Check that the burner is lit by looking through the
cooking grills. You should see a flame.
m WARNING: Do not lean over the open
barbecue while igniting.
m WARNING: If burner fails to ignite within
five seconds, stop, turn the burner control
knob to o and wait five minutes to allow
the gas to clear before you try again or
light with a match.
TO EXTINGUISH BURNER
Push burner control knob in and turn it clockwise to the o
() position.
m CAUTION: Do not fold in side tables until
barbecue is cold (Q 2000, Q 2200).
2
1
3
4
6
5
Some batteries have a plastic
protective wrap around them.
This plastic must be removed
before you attempt to ignite
your barbecue. Do not confuse
this plastic with the battery
label.
model lighting
instructions
document
use these illustrations
if work
BURNER IGNITION & USAGE
A) Open the barbecue lid (1) and unfold sidetables if
applicable (2).
BURNER IGNITION - Getting started
BURNER IGNITION - Ignition system BURNER IGNITION - Lighting with a match
Depress the RESET button (illuminated red) continuously
for ve (5) seconds to reset the Flame iQ (red light will go
out). Repeat the ignition steps as above.
RESETTING THE Flame iQ AFTER FLAME
FAILURE AND LOCKOUT
TO EXTINGUISH BURNER
Push burner control knob in and turn it clockwise to
the OFF (O) position. Depress the ON/OFF button on the
Flame iQ control box to switch off the Flame iQ.
F) Strike a match and put the ame under the matchlight
hole (5). While holding the lit match, push burner control
knob in and turn it counter clockwise to start/high ( )
position (6).
16 WWW.WEBER.COM
BURNER IGNITION & USAGE
Summary lighting instructions are on the
instruction tag(Q 1000, Q 1200) or the right
METHODS OF BURNER
IGNITION
There are two ways to ignite
the burner. The first is by using
the ignition system built into
your barbecue. The second is
with a match.
Next are the steps for
igniting your barbecue using
the ignition system. On the
following page are steps for
igniting your barbecue with a
match.
BURNER IGNITION
A) Open the barbecue lid (1).
mDANGER
Failure to open the lidbeforeigniting the
barbecue’sburner, or not waiting five
minutes to allow the gas to clear if the
barbecue does not light, may result in an
explosive flare-up which can cause serious
bodily injury or death.
B) (2) (Q 2000 ™,Q 2200™).
C) Make sure the burner control knob is turned to t
((3) . Check by pushing burner control knob
in and turning it clockwise until it stops.
D) Turn gas supply on at source.
E) Push burner control knob in and turn it
counterclockwise to start/high ( ) position (4) .
F1) Push the red igniter button several times, so it clicks
each time (5) (Q 1000 ™, Q 2000 ™).
OR
F2) Push and hold in the electronic igniter button (6)
(Q 1200 ™, Q 2200 ™). You will hear the igniter clicking.
G) Check that the burner is lit by looking through the
cooking grills . You should see a flame.
mWARNING: Do not lean over the open
barbecue while igniting.
mWARNING: If burner fails to ignite within
five seconds, stop, turn the burner control
the gas to clear before you try again or
light with a match.
TO EXTINGUISH BURNER
( ) position.
mCAUTION: Do not fold in side tables until
barbecue is cold (Q 2000, Q 2200).
2
1
3
4
6
5
Some batteries have a plastic
protective wrap around them.
This plastic must be removed
before you attempt to ignite
your barbecue . Do not confuse
this plastic with the battery
label.
model lighting
instructions
document
use these illustrations
if work
6
16 WWW.WEBER.COM
BURNER IGNITION & USAGE
Summary lighting instructions are on the
instruction tag(Q 1000, Q 1200) or the right
METHODS OF BURNER
IGNITION
There are two ways to ignite
the burner. The first is by using
the ignition system built into
your barbecue. The second is
with a match.
Next are the steps for
igniting your barbecue using
the ignition system. On the
following page are steps for
igniting your barbecue with a
match.
BURNER IGNITION
A) Open the barbecue lid (1).
mDANGER
Failure to open the lidbeforeigniting the
barbecue’sburner, or not waiting five
minutes to allow the gas to clear if the
barbecue does not light, may result in an
explosive flare-up which can cause serious
bodily injury or death.
B) (2) (Q 2000 ™,Q 2200™).
C) Make sure the burner control knob is turned to t
((3) . Check by pushing burner control knob
in and turning it clockwise until it stops.
D) Turn gas supply on at source.
E) Push burner control knob in and turn it
counterclockwise to start/high ( ) position (4).
F1) Push the red igniter button several times, so it clicks
each time (5) (Q 1000 ™, Q 2000 ™).
OR
F2) Push and hold in the electronic igniter button (6)
(Q 1200 ™, Q 2200 ™). You will hear the igniter clicking.
G) Check that the burner is lit by looking through the
cooking grills . You should see a flame.
mWARNING: Do not lean over the open
barbecue while igniting.
mWARNING: If burner fails to ignite within
five seconds, stop, turn the burner control
the gas to clear before you try again or
light with a match.
TO EXTINGUISH BURNER
( ) position.
mCAUTION: Do not fold in side tables until
barbecue is cold (Q 2000, Q 2200).
2
1
3
4
6
5
Some batteries have a plastic
protective wrap around them.
This plastic must be removed
before you attempt to ignite
your barbecue . Do not confuse
this plastic with the battery
label.
model lighting
instructions
document
use these illustrations
if work
7
16 WWW.WEBER.COM
BURNER IGNITION & USAGE
Summary lighting instructions are on the
instruction tag (Q 1000, Q 1200) or the right
fold-out table (Q 2000, Q2200).
METHODS OF BURNER
IGNITION
There are two ways to ignite
the burner. The first is by using
the ignition system built into
your barbecue. The second is
with a match.
Next are the steps for
igniting your barbecue using
the ignition system. On the
following page are steps for
igniting your barbecue with a
match.
BURNER IGNITION
A) Open the barbecue lid (1).
m DANGER
Failure to open the lid before igniting the
barbecue’s burner, or not waiting five
minutes to allow the gas to clear if the
barbecue does not light, may result in an
explosive flare-up which can cause serious
bodily injury or death.
B) Unfold the side tables(2) (Q 2000™, Q 2200™).
C) Make sure the burner control knob is turned to the o
() position(3). Check by pushing burner control knob
in and turning it clockwise until it stops.
D) Turn gas supply on at source.
E) Push burner control knob in and turn it
counterclockwise to start/high ( ) position (4).
F1) Push the red igniter button several times, so it clicks
each time (5) (Q 1000™, Q 2000™).
OR
F2) Push and hold in the electronic igniter button (6)
(Q 1200™, Q 2200™). You will hear the igniter clicking.
G) Check that the burner is lit by looking through the
cooking grills. You should see a flame.
m WARNING: Do not lean over the open
barbecue while igniting.
m WARNING: If burner fails to ignite within
five seconds, stop, turn the burner control
knob to o and wait five minutes to allow
the gas to clear before you try again or
light with a match.
TO EXTINGUISH BURNER
Push burner control knob in and turn it clockwise to the o
( ) position.
m CAUTION: Do not fold in side tables until
barbecue is cold (Q 2000, Q 2200).
2
1
3
4
6
5
Some batteries have a plastic
protective wrap around them.
This plastic must be removed
before you attempt to ignite
your barbecue. Do not confuse
this plastic with the battery
label.
model lighting
instructions
document
use these illustrations
if work
WWW.WEBER.COM 17
BURNER IGNITION & USAGE
BURNER IGNITION –
Lighting with a Match
A) Open the barbecue lid (1).
m DANGER
Failure to open the lid before igniting the
barbecue’s burner, or not waiting five
minutes to allow the gas to clear if the
barbecue does not light, may result in an
explosive flare-up which can cause serious
bodily injury or death.
B) Unfold the side tables(2) (Q 2000™, Q 2200™).
C) Make sure the burner control knob is turned to the o
() position(3). Check by pushing burner control knob
in and turning it clockwise until it stops.
D) Turn gas supply on at source.
E) Strike a match and put the flame under the matchlight
hole (4). While holding lit match, push burner control
knob in and turn it counterclockwise to start/high ( )
position (5).
F) Check that the burner is lit by looking through the
cooking grills (6). You should see a flame.
m WARNING: Do not lean over the open
barbecue while igniting. Keep your face
and body at least 30 cm (12 in) away
from the matchlight hole when lighting
thebarbecue.
m WARNING: If the burner fails to ignite
within five seconds, stop, turn the burner
control knob to o and wait five minutes
to allow the gas to clear before you try
again.
TO EXTINGUISH BURNER
Push burner control knob in and turn it clockwise to the o
() position.
m CAUTION: Do not fold in side tables until
barbecue is cold (Q 2000, Q 2200).
2
1
3
5
4
6
WWW.WEBER.COM 17
BURNER IGNITION & USAGE
BURNER IGNITION –
Lighting with a Match
A) Open the barbecue lid (1).
m DANGER
Failure to open the lid before igniting the
barbecue’s burner, or not waiting five
minutes to allow the gas to clear if the
barbecue does not light, may result in an
explosive flare-up which can cause serious
bodily injury or death.
B) Unfold the side tables(2) (Q 2000™, Q 2200™).
C) Make sure the burner control knob is turned to the o
() position(3). Check by pushing burner control knob
in and turning it clockwise until it stops.
D) Turn gas supply on at source.
E) Strike a match and put the flame under the matchlight
hole (4). While holding lit match, push burner control
knob in and turn it counterclockwise to start/high ( )
position (5).
F) Check that the burner is lit by looking through the
cooking grills (6). You should see a flame.
m WARNING: Do not lean over the open
barbecue while igniting. Keep your face
and body at least 30 cm (12 in) away
from the matchlight hole when lighting
thebarbecue.
m WARNING: If the burner fails to ignite
within five seconds, stop, turn the burner
control knob to o and wait five minutes
to allow the gas to clear before you try
again.
TO EXTINGUISH BURNER
Push burner control knob in and turn it clockwise to the o
() position.
m CAUTION: Do not fold in side tables until
barbecue is cold (Q 2000, Q 2200).
2
1
3
5
4
5
DANGER: Failure to open the lid before igniting the
barbecue’s burner, or not waiting ve minutes to
allow the gas to clear if the barbecue does not light,
may result in an explosive are-up which can cause
serious bodily injury or death.
B) Make sure the burner control knob is turned to the OFF
(O) position (3). Check by pushing burner control knob in
and turning it clockwise until it stops.
C) Ensure that the Flame iQ has power (either by way of
12 V or 240 V) and the power supply is switched on.
D) Turn gas supply on at source.
E) Depress the ON/OFF button on the Flame iQ control
box– the button will illuminate green (4).
Note: You have 30 seconds to ignite the barbecue from
when you press the Flame iQ ON button. Should the
barbecue not ignite within the 30 seconds the Flame iQ
will go into lockout and need to be reset.
F) Push the burner control knob in and turn it counter
clockwise to start/high ( ) position (5).
G1) Push the red igniter button several times, so it clicks
each time (6) (Q1000)
G2) Push and hold in the electronic igniter button ( ) (7)
(Q1200). You will hear the igniter clicking.
OR,
H) Once ame is detected, the blue light on the Flame iQ
control box illuminates (8).
I) After ignition close the barbecue lid to enable
pre-heating to commence.
G) Once ame is detected, the blue light on the Flame iQ
control box illuminates (7).
H) After ignition close the barbecue lid to enable
pre-heating to commence.
ON/OFF
4
8
7
RESET
Hold for
5 seconds
There are two ways to ignite the burner. The
rst is by using the ignition system built into
your barbecue. The second is with a match.
METHODS OF BURNER IGNITION
Flame iQ Q1000 & Q1200
Summary lighting instructions are on the
instruction tag of your barbecue and Flame iQ.
Only use this method if your ignition system is not
working.

8
Barbecue burner does not ignite.
Flame is low when burner control knob is on high ( )
position
If you are unable to solve a problem contact the service department who will assist with your enquiry.
PROBLEMS SOLUTIONS
TROUBLESHOOTING
m ATTENTION: This product has been safety tested and is only certified for use in a specific country. Refer to country designation
located on outer carton.
These parts may be gas carrying or gas burning components. Please contact Weber-Stephen Products LLC Customer Service
Department for genuine Weber-Stephen Products LLC replacement part(s) information.
m WARNING: Do not attempt to make any repair to gas carrying, gas burning, igniter components, or structural components without
contacting Weber-Stephen Products LLC Customer Service Department. Your actions, if you fail to follow this Product Warning,
may cause a fire, an explosion, or structural failure resulting in serious personal injury or death as well as damage to property.
Weber-Stephen Products LLC
www.weber.com
© 2022 Designed and engineered by Weber-Stephen Products LLC,
1415 S. Roselle Road, Palatine, Illinois 60067 USA.
Weber-Stephen Products (Aust) Pty Ltd.
Level 1, 142-144 Fullarton Road
ROSE PARK SA 5067 AUSTRALIA
[phone] | www.weberbbq.com.au
WEBER New Zealand ULC
86 East Highbrook Drive
East Tamaki, Auckland 2013 NEW ZEALAND
[phone] | www.WEBERnz.co.nz
© 2023 Designed and engineered by Weber-Stephen Products (Aust) Pty Ltd.
Level 1, 142-144 Fullarton Road, Rose Park SA 5067 AUSTRALIA
The Flame iQ is covered by AU Patent 2021105238
These parts may be gas carrying or gas burning components.
ATTENTION: This product has been safety tested and is only certified for use in Australia and New Zealand.
WARNING: Do not attempt to make any repair to gas carrying or burning, igniter components, or structural components without contacting
Weber-Stephen Products Australia or New Zealand Customer Service Department. Your actions, if you fail to follow this Product Warning,
may cause a re, an explosion or structural failure resulting in serious personal injury or death as well as damage to property.
The WEBER Flame iQ contains no user serviceable
parts.
DO NOT MODIFY THIS PRODUCT
SERVICING SHALL ONLY BE CARRIED OUT BY
AUTHORISED PERSONNEL
For all Service needs contact:
Weber-Stephen Products (Aust) Pty Ltd
ABN 18 006 305 237
Level 1, 142-144 Fullarton Road, Rose Park SA 5067
Customer Service Ph: 1300 301 290 (toll free)
Email: [e-mail]
Website: www.weber.com/au
Weber-Stephen Products New Zealand
86 East Highbrook Drive
East Tamaki, Auckland 2013
Customer Service Ph: 0800 493 237 (toll free)
Email: [e-mail]
Website: www.weber.com/nz
SERVICING & SPARE PARTS
Check the Flame iQ has power and is turned on (the ON/OFF button is illuminated green). When the Flame iQ is turned
on you will hear a soft click as the solenoid opens to let the gas through to the barbecue.
Fuel could be low or empty. Rell LPG cylinder.
Check burner ports under the sensor are clean.
Ensure barbecue is turned off, disconnect hose from LPG cylinder, wait 30 seconds and reconnect. Repeat ignition
procedure.
Ignitor fails to work. See page 7 for lighting instructions using a match.
Turn barbecue off, disconnect hose from LPG cylinder, wait 30 seconds and reconnect. Repeat ignition procedure.
Fuel could be low or empty. Rell LPG cylinder.
Fuel hose could be bent or kinked. Straighten fuel hose.
You have 30 seconds to ignite the barbecue after turning on the Flame iQ device. Refer burner ignition on page 7.
If the barbecue does not ignite, the Flame iQ will lock-out, the gas ow will stop, and the red reset light will illuminate.
Press the reset button for 5 seconds and it will turn off.
Press the ON/OFF button and repeat the ignition procedure.
Level 1, 142-144 Fullarton Road
Rose Park SA 5067 Australia
1300 301 290 (toll free) | www.weber.com/au
86 East Highbrook Drive
East Tamaki, Auckland 2013 New Zealand
0800 493 237 (toll free) | www.weber.com/nz
Weber-Stephen Products New Zealand
Weber-Stephen Products (Aust) Pty Ltd