Gira DALI 5422 00 User manual

Wireless DALI control unit, 1-gang Mini
Wireless DALI control unit, 1-gang Mini
Order no.: 5422 00
Operating instructions
1 Safety instructions
Electrical devices may only be mounted and connected by electrically skilled persons.
Serious injuries, fire or property damage possible. Please read and follow manual fully.
Danger of electric shock. Always disconnect before carrying out work on the device or load. In
so doing, take all the circuit breakers into account, which support dangerous voltages to the
device and or load.
Danger of electric shock. Device is not suitable for disconnection from supply voltage.
These instructions are an integral part of the product, and must remain with the end customer.
Further information about this device can be found in the operation manual on our web-
site.
2 Device components
Figure1: Front view
(1) Operating mode switch
(2) Button Prog
(3) Status LED
(4) Measuring points for voltage measurement, terminals rear-mounted
3 Intended use
– Switching and brightness setting of DALI luminaires
– Operation with suitable radio transmitters
– Mounting in appliance box according to DIN 49073 in combination with a suitable cover
– Installation in surface-mounted housing or panel-mounted housing (accessories) for sus-
pended ceilings
Product characteristics
– Joint operation of all the connected DALI ballasts, broadcast.
1 / 14
32580922 10864978 22.08.2019

Wireless DALI control unit, 1-gang Mini
– Electronic short-circuit protection of the DALI supply with permanent switch-off after 8
seconds
– Electronic over-temperature protection of the DALI supply with self-retain
– DALI supply for a maximum of 12 subscribers
– Parallel switching of up to 6 DALI control units with the option of supplying up to 72 DALI
subscribers
– Switch-on brightness can be saved permanently
– Minimum brightness can be saved permanently
– Scene operation possible
– Status indication with LED
– Status feedback to radio transmitter
– DALI ballast is switchable with Prog button
Can be set with eNet server:
– Maximum brightness
– Dimming speed
– Switch-on delay / switch-off delay
– Dim up/dim down ramp
– Switch-off warning
– Operation locks
– Continuous on, Continuous off
– Hotel function
– Run-on time
– Light control
When operating with the eNet Server, operation and signalling could vary from what is de-
scribed here.
Supplementary functions with eNet Server:
– Fully encrypted radio transmission (AES-CCM) from eNet Server software version 2.0
– Update of the device software
– Repeater function
– Reading of error memory
Product characteristics
– Joint operation of all the connected DALI ballasts, broadcast.
– Electronic short-circuit protection of the DALI supply with permanent switch-off after 8
seconds
– Electronic over-temperature protection of the DALI supply with self-retain
– DALI supply for a maximum of 12 subscribers
– Parallel switching of up to 6 DALI control units with the option of supplying up to 72 DALI
subscribers
– Switch-on brightness can be saved permanently
– Minimum brightness can be saved permanently
– Scene operation possible
– Status indication with LED
– Status feedback to radio transmitter
– DALI ballast is switchable with Prog button
Can be set with eNet server:
– Maximum brightness
– Dimming speed
– Switch-on delay / switch-off delay
– Dim up/dim down ramp
2 / 14
32580922 10864978 22.08.2019

Wireless DALI control unit, 1-gang Mini
– Switch-off warning
– Operation locks
– Continuous on, Continuous off
– Hotel function
– Run-on time
– Light control
When operating with the eNet Server, operation and signalling could vary from what is de-
scribed here.
The parameter list is in the Internet in the documentation for this device.
Supplementary functions with eNet Server:
– Fully encrypted radio transmission (AES-CCM) from eNet Server software version 2.0
– Update of the device software
– Repeater function
– Reading of error memory
Behaviour after mains voltage failure and return
The response after mains voltage return can be configured with the eNet server. Default setting:
The light is switched off after mains voltage return. After a brief voltage failure or in the case of
operation on several conductors, it might take a few seconds until the light is switched off.
Within this time frame, a value stored in the DALI ballast – PowerON-Level – is retrieved.
The brightness of the lighting when DALI- telegrams are missing – PowerON-Level – and
in case of DALI system voltage failure – SystemFailure-Level – is stored in the DALI bal-
last and cannot be changed using the actuator.
4 Operation
Operation with radio transmitter
Operation is with radio transmitters, please observe the radio transmitter instructions.
Operation always applies to all the connected DALI ballasts, broadcast.
5 Information for electrically skilled persons
5.1 Fitting and electrical connection
DANGER!
Electrical shock when live parts are touched.
Electrical shocks can be fatal.
Before carrying out work on the device or load, disengage all the corresponding cir-
cuit breakers. Cover up live parts in the working environment.
Connecting and mounting the control unit.
To ensure good transmission quality, keep a sufficient distance from any possible sources of in-
terference, e.g. metallic surfaces, microwave ovens, hi-fi and TV systems, ballasts or trans-
formers.
3 / 14
32580922 10864978 22.08.2019

Wireless DALI control unit, 1-gang Mini
Figure2: Connection example
The connected DALI subscribers may be operated on different phase conductors.
The control cable and load cable can be run in a shared cable, e.g. NYM J 5×1.5.
Ensure that the control cable with regards type, cross-section and routing complies with
the VDE specifications for 250 V cables, DALI interface has basic insulation.
￭ Connect control unit (5) and DALI ballasts (6) as shown in the connection example
(Figure 2). At the same time, note the information given by the manufacturers of the bal-
lasts.
In the case of more than 12 DALI subscribers, up to five additional control units can be
connected. When doing so, ensure correct polarity.
￭ If multiple circuit breakers supply dangerous voltages to the device or load, couple the
miniature circuit breakers or label them with a warning, to ensure disconnection is guaran-
teed.
￭ Insert the control unit into the appliance box in such a way that the Prog button (2) and
status-LED (3) are visible.
Figure3: Operating mode switch
Switch position Function
PC Operating mode, parameter set with eNet
server *)
DALI DALI mode
min. Setting of the minimum brightness
*) If the operating mode switch is turned from the position PC, the operating mode and
parameters are set to the default setting. The settings made with the eNet Server will
be lost.
￭ Set the operating mode switch (1).
￭ Switch on mains voltage.
The ballasts can be switched by briefly pressing the Prog button.
Status-LED (3) lights up: switched on
Status LED (3) off: switched off
4 / 14
32580922 10864978 22.08.2019

Wireless DALI control unit, 1-gang Mini
￭ Perform commissioning.
￭ Mount the cover.
5.2 Commissioning
The control unit can also be commissioned with eNet server as an alternative to the com-
missioning described here.
Connecting to radio transmitters
If several control units are switched in parallel, all radio transmitters will only connect to
one control unit.
Load is switched off.
￭ Press button Prog (2) for longer than 4 seconds.
The status LED (3) flashes after 4 seconds. The control unit is in programming mode for
approx. 1 minute.
￭ Switch radio transmitter to programming mode (see radio transmitter instructions).
￭ Trigger telegram on the radio transmitter.
The status LED lights up for 5 seconds.
The control unit is connected to the radio transmitter. The control unit and radio transmit-
ter exit the programming mode automatically.
If the status LED of the control unit flashes 3 times at 1-second intervals for
approx. 5 seconds, then the programming operation was not successful. All the memory
locations in the actuator or radio transmitter are occupied.
All On and All Off buttons of a radio transmitter are connected to the control unit automat-
ically as soon as the first connection to the radio transmitter takes place.
The scene buttons must be connected separately to the control unit.
Disconnecting connection to a radio transmitter
￭ Carry out the same steps as when connecting (see Connecting to radio transmitter).
The status LED (3) flashes quickly for 5 seconds. The control unit is disconnected from
the radio transmitter. The control unit and radio transmitter exit the programming mode
automatically.
If there several connections or scene buttons for a radio transmitter, all connections must
be disconnected individually.
All On and All Off buttons of a radio transmitter are disconnected automatically as soon as
the last connection to the radio transmitter is disconnected. Manual disconnection is not
possible.
Resetting control unit to the default setting
All connections to radio transmitters are disconnected and parameters are reset to default set-
ting.
The connections in the radio transmitters are preserved and must be deleted separately.
Load is switched off.
￭ Press the Prog button for at least 20 seconds.
The status LED flashes after 4 seconds. After 20 seconds the status LED flashes faster.
￭ Release Prog button and press briefly once again within 10 seconds.
The status LED flashes more slowly for approx. 5 seconds.
Reset control unit to default setting.
Setting the minimum brightness
The minimum brightness can be set within a range of approx. 1...67 %, if, e.g. the light flickers
at low brightness or to compensate for differences in brightness.
5 / 14
32580922 10864978 22.08.2019

Wireless DALI control unit, 1-gang Mini
￭ Switch on light.
￭ Turn operating mode switch (1) to the min. position.
The light switches to maximum brightness for approx. 2 seconds.
The light switches off and after approx. 2 seconds switches to the brightness that was last
set.
￭ Adjust brightness with the radio transmitter.
￭ Turn operating mode switch to the original position again.
When leaving the position min., the minimum brightness is saved. As confirmation, the
light switches to maximum brightness and switches to the set minimum brightness after
approx. 2 seconds.
Depending on the DALI ballast used, the signalling may vary from what is described here.
Save switch-on brightness
￭ Switch on light.
￭ Adjust brightness with the radio transmitter.
￭ Press button Prog (2) for longer than 4 seconds.
The light switches off briefly and then switches on again to the new switch-on brightness.
Switch-on brightness is saved.
Alternatively, the switch-on brightness can be saved with a radio transmitter, e.g. wall
transmitter.
6 Technical data
Rated voltage AC 230 V~
Mains frequency 50 / 60 Hz
Power consumption max. 2 W
Ambient temperature -25 ... +70 °C
Rated voltage DALI DC 16 V (typ.)
Output current max. 24 mA
Number of DALI subscribers max. 12
Number of parallel control units max. 6
Power reduction
Number of DALI subscribers over 45 °C max. 8
Connection
single stranded 0.75 ... 4 mm²
Finely stranded with conductor sleeve 0.75 ... 2.5 mm²
Dimensions Ø×H 53×28 mm
Radio frequency 868.0 ... 868.6 MHz
Transmission capacity max. 20 mW
Transmitting range in free field typ. 100 m
Receiver category 2
6 / 14
32580922 10864978 22.08.2019

Wireless DALI control unit, 1-gang Mini
7 Parameter list
The device parameters can be changed with the eNet server:
Device and channels
Parameters Setting options, Basic setting Explanations
Function Light, unused
Basic setting: Light
Light
The channel is integrated for
the "Lighting" central function
in the eNet SMART HOME
app.
Unused
The channel is not displayed
in the eNet SMART HOME
app and is disabled for use in
the commissioning interface.
Operating mode Normal operation
Continuous on
Continuous off
Basic setting: Normal Opera-
tion
Normal operation
The output can be operated
with radio transmitters and the
Prog button.
Continuous on
The output switches to con-
tinuously "On". All operations
of radio transmitters and the
Prog button are ignored.
Continuous off
The output switches to con-
tinuously "Off". All operations
of radio transmitters and the
Prog button are ignored.
Advanced device settings
Parameters Setting options, Basic setting Explanations
Manual commissioning On, Off
Basic setting: On
Blocks manual commissioning
for the device channel.
Note: In the "Off" setting, the
device cannot be reset to the
factory setting.
Repeater mode On, Off
Basic setting: Off
In addition to its other func-
tions, the device can be used
as a repeater. In the "On" set-
ting, the device repeats all the
received telegrams.
Channel settings
Parameters Setting options, Basic setting Explanations
Switch-on brightness 1...100 %
Basic setting: 100 %
During brief operation, the out-
put switches on at the set
switch-on brightness.
Note: If the value is above the
set maximum brightness or
below the minimum bright-
7 / 14
32580922 10864978 22.08.2019

Wireless DALI control unit, 1-gang Mini
Parameters Setting options, Basic setting Explanations
ness, then the system will
switch to the appropriate limit
value.
Minimum brightness 1...67 %
Basic setting: 5 %
Specifies the minimum set-
table brightness.
Note: If parameters or scene
values are set to a level lower
than the minimum brightness,
then the system will dim to
minimum brightness.
Maximum brightness 75...100 %
Basic setting: 100 %
Specifies the maximum set-
table brightness.
Note: If parameters or scene
values are set to a level higher
than the maximum brightness,
then the system will dim to
maximum brightness.
Dimming adjustment time 1…60 s
Basic setting: 4 s
Time from minimum bright-
ness until reaching maximum
brightness (dimming speed).
Switch-on delay 0 s … 24 h
Basic setting: 0 s
The load switches on after a
delay. Repeated switch-on
commands restart the delay
time. If the load has not yet
been switched on due to the
delay when a switch-off com-
mand comes, then the load
will remain off.
Note: The set time apply to
operation using radio transmit-
ters. The device is switched
immediately when the Prog
button is pressed.
Switch-off delay 0 s … 24 h
Basic setting: 0 s
The load switches off after a
delay. Repeated switch-off
commands restart the delay
time. If the load has not yet
been switched off due to the
delay when a switch-on com-
mand comes, then the load
will remain on.
Note: The set time apply to
operation using radio transmit-
ters. The device is switched
immediately when the Prog
button is pressed.
Dim up ramp 0 s … 24 h
Basic setting: 0 s
Time between switch-on and
reaching switch-on brightness.
The light is switched on at
minimum brightness and then
dimmed to the switch-on
brightness.
Only applies to switch-on with
transmitters (short operation).
8 / 14
32580922 10864978 22.08.2019

Wireless DALI control unit, 1-gang Mini
Parameters Setting options, Basic setting Explanations
If scenes are recalled or
switching uses logic modules,
the switch-on brightness is ap-
proached using so-called soft
dimming (not configurable).
Dim down ramp 0 s … 24 h
Basic setting: 0 s
Time until reaching minimum
brightness. The light is
dimmed to minimum bright-
ness and then switched off.
Only applies to switch-off with
transmitters (short operation).
If scenes are recalled or
switching uses logic modules,
the system switches off dir-
ectly.
Run-on time 0 s … 24 h
Basic setting: 0 s
As soon as a run-on time has
been entered, the actuator will
no longer remain on perman-
ently, but only for the length of
the run-on time. The run-on
time is restarted if actuation is
repeated. This parameter is
directly connected to the
"Manual switch-off of run-on
time" parameter.
Note: The set time apply to
operation using radio transmit-
ters. The device is switched
immediately when the Prog
button is pressed.
Manual switch-off of the run-
on time
On, Off
Basic setting: Off
Allows manual switch-off of a
running run-on time. If the
parameter is switched off,
then a switch-off command
will also switch the actuator
on. Only visible if a run-on
time was set.
Operating hours 0...65535
Basic setting: Current value
The time is counted during
which the load is physically
switched on.
This parameter can be reset
to "0", for example after ex-
changing the load.
The Reset button is used to
9 / 14
32580922 10864978 22.08.2019

Wireless DALI control unit, 1-gang Mini
Parameters Setting options, Basic setting Explanations
reset the counter to "0". The
device must be programmed
to apply the change.
Extended channel settings
Parameters Setting options, Basic setting Explanations
Operating mode Normal operation
Continuous on
Continuous off
Basic setting: Normal Opera-
tion
see Device and channels
Manual commissioning On, Off
Basic setting: On
Blocks manual commissioning
for the device channel.
Note: In the "Off" setting, the
device cannot be reset to the
factory setting.
Local Operation On, Off
Basic setting: On
Blocks the output for operation
using the Prog button.
Behaviour on voltage return On
Off
Last value
Configured brightness
Basic setting: Off
Defines the behaviour of the
output after voltage return.
Brightness on voltage return 0...100 %
Basic setting: 100 %
Brightness value, set by the
output after voltage return
(mains voltage). The para-
meter "Behaviour after voltage
return" must be set to "Con-
figured position".
Note: If the value is above the
set maximum brightness or
below the minimum bright-
ness, then the system will
switch to the appropriate limit
value.
Behaviour after the end of the
disabling function
On
Off
no change
Last value
Basic setting: No change
Behaviour of the output when
a block is removed.
Manual saving of the scene
values
On, Off
Basic setting: On
Disables the saving of the cur-
rent brightness value as scene
value in an actuator for a com-
mand via a transmitter.
Switch-off warning On, Off
Basic setting: Off
If the switch-off warning is act-
ive, then, during switch-off, the
system dims to minimum
brightness within 30 seconds
and only then switches off. If
the parameter "Dim down
ramp" is configured as longer
than 30 s, then the length of
10 / 14
32580922 10864978 22.08.2019

Wireless DALI control unit, 1-gang Mini
Parameters Setting options, Basic setting Explanations
the dim down ramp is applied.
If, during the dim down opera-
tion, another command is
given, e.g. switch on or scene
recall, then the switch-off
warning stops and the com-
mand is executed. A switch-off
command restarts the time for
the switch-off warning.
Note: The set time apply to
operation using radio transmit-
ters. The device is switched
immediately when the Prog
button is pressed.
Priority, lock-out protection 0...4
Basic setting: 1
Specifies the priority for recall-
ing and removing a scene of
type Lock-out protection for
the channel.
Note: 1 is the highest priority
and 4 the lowest. 0 means no
priority.
Activate lock-out protection
brightness value
0…100 %
Basic setting: 0 %
Defines the behaviour of the
output on activating the lock-
out protection.
Deactivate lock-out protection
brightness value
0…100 %
Basic setting: 0 %
Defines the behaviour of the
output on deactivating the
lock-out protection. Only vis-
ible when the priority for the
lock-out protection is 0.
Priority, restraint 0...4
Basic setting: 2
Specifies the priority for recall-
ing and removing a scene of
type Restraint for the channel.
Activate forced operation
brightness value
0…100 %
Basic setting: 100 %
Defines the behaviour of the
output on activating the forced
operation.
Deactivate forced operation
brightness value
0…100 %
Basic setting: 0 %
Defines the behaviour of the
output on deactivating the
forced operation. Only visible
when the priority for the forced
operation is 0.
Priority, wind alarm 0...4
Basic setting: 3
Specifies the priority for recall-
ing and removing a scene of
type Wind alarm for the chan-
nel.
Activate wind alarm brightness
value
0…100 %
Basic setting: 0 %
Defines the behaviour of the
output on activating the wind
alarm.
Deactivate wind alarm bright-
ness value
0…100 %
Basic setting: 0 %
Defines the behaviour of the
output on deactivating the
wind alarm. Only visible when
the priority for the wind alarm
is 0.
11 / 14
32580922 10864978 22.08.2019

Wireless DALI control unit, 1-gang Mini
Parameters Setting options, Basic setting Explanations
Priority, sun protection 0...4
Basic setting: 0
Specifies the priority for recall-
ing and removing a scene of
type Sun protection for the
channel.
Activate sun protection bright-
ness value
0…100 %
Basic setting: 100 %
Defines the behaviour of the
output on activating the sun
protection.
Deactivate sun protection
brightness value
0…100 %
Basic setting: 0 %
Defines the behaviour of the
output on deactivating the sun
protection. Only visible when
the priority for the sun protec-
tion is 0.
Priority, twilight 0...4
Basic setting: 0
Specifies the priority for recall-
ing and removing a scene of
type Twilight for the channel.
Activate twilight brightness
value
0…100 %
Basic setting: 100 %
Defines the behaviour of the
output on activating the twi-
light function.
Deactivate twilight brightness
value
0…100 %
Basic setting: 0 %
Defines the behaviour of the
output on deactivating the twi-
light function. Only visible
when the priority for the twi-
light function is 0.
Switch off brightness over-
shoot
On, Off
Basic setting: On
Allows automatic switch-off
according to the brightness. If
the parameter is On, then the
light controller switches off
automatically when the bright-
ness setpoint is greatly ex-
ceeded.
Note: This parameter is not
yet active, as a light controller
has not yet been implemen-
ted.
Switch on brightness under-
shoot
On, Off
Basic setting: Off
Allows automatic switch-on
according to the brightness. If
the parameter is On, then the
light controller switches on
automatically when the bright-
ness setpoint is greatly under-
shot. We recommend only us-
ing the parameter in connec-
tion with the parameter
"Switch-off on brightness over-
shoot".
Note: This parameter is not
yet active, as a light controller
has not yet been implemen-
ted.
Hotel function On, Off
Basic setting: Off
If the hotel function is activ-
ated, the system will dim to 20
% brightness when a switch-
off command is made. Switch-
12 / 14
32580922 10864978 22.08.2019

Wireless DALI control unit, 1-gang Mini
Parameters Setting options, Basic setting Explanations
off is only possible with a
forced position command.
Note: If the minimum bright-
ness is set to greater than 20
%, then the system dims to
the set minimum brightness
when the hotel function is ac-
tivated.
Information window
In the Information window, the load can be controlled and the information about the device can
be displays.
Channel control/channel information
Display value Explanations
Current dimming value The load can be dimmed using the slider or a
brightness value entry.
Load state The load can be switched on or off.
Restraint Display of forced position status.
Operating hours Display of the operating hours since the last
restart in the Settings window Einstellungen.
8 Troubleshooting
DALI ballasts switch to System-Failure-Level. No operation is possible.
Cause 1: short-circuit protection of the control unit has triggered, DALI voltage is switched off.
Status LED (3) flashes 3 times at intervals of 1 second.
Disconnect control unit from mains, also switch off circuit breaker.
Eliminate short-circuit.
Switch circuit breakers and control unit on again.
Short-circuit protection is not based on a conventional fuse, no metallic separation of the
DALI current.
Cause 2: overtemperature protection of the control unit has triggered, DALI voltage is switched
off. Status LED flashes 3 times at intervals of 1 second.
Disconnect control unit from mains, also switch off circuit breaker.
Let the control unit cool down for at least 15 minutes.
Check the installation situation.
Switch additional control unit in parallel, max. 6 per system.
Reduce the connected DALI subscribers.
Switch circuit breakers and control unit on again.
9 Accessories
Installation adapter Mini housing Order no. 5429 00
eNet Server Order no. 5301 00
Mounting adapter for mini housing Art. no. FM-EBG
eNet server for rail mounting Art. no. ENET-SERVER
13 / 14
32580922 10864978 22.08.2019

Wireless DALI control unit, 1-gang Mini
10 Conformity
Hereby Gira Giersiepen GmbH & Co. KG declares that the radio system type
Order no. 5422 00
corresponds to the directive 2014/53/EU. You can find the full article number on the device. The
complete text of the EU Declaration of Conformity is available under the Internet address:
www.gira.de/konformitaet
Hereby Albrecht Jung GmbH & Co. KG declares that the radio system type
Art. no. FMSTD8UP
corresponds to the directive 2014/53/EU. You can find the full article number on the device. The
complete text of the EU Declaration of Conformity is available under the Internet address:
www.jung.de/ce
11 Warranty
The warranty is provided in accordance with statutory requirements via the specialist trade.
Please submit or send faulty devices postage paid together with an error description to your re-
sponsible salesperson (specialist trade/installation company/electrical specialist trade). They will
forward the devices to the Gira Service Center.
The warranty is provided in accordance with statutory requirements via the specialist trade.
Gira
Giersiepen GmbH & Co. KG
Elektro-Installations-
Systeme
Industriegebiet Mermbach
Dahlienstraße
42477 Radevormwald
Postfach 12 20
42461 Radevormwald
Deutschland
Tel [phone] - 602-0
Fax [phone] - 602-191
www.gira.de
[email protected]
14 / 14
32580922 10864978 22.08.2019