Weco Discovery 300 User manual

Cod. 006.0001.1920
11/02/2021 V.2.2
Discovery 300
Instruction manual
ENG
Translation of original instructions

WELD THE WORLD
Cod. 006.0001.1920
11/02/2021 V.2.2 Discovery 300
2
ENGLISH

WELD THE WORLD
Cod. 006.0001.1920
11/02/2021 V.2.2
Discovery 300
3
ENGLISH
INDEX
1 INTRODUCTION.......................................................................................................................................... 4
1.1 INTRODUCTION.......................................................................................................................................... 5
2 INSTALLATION .......................................................................................................................................... 5
2.1 CONNECTIONS TO THE ELECTRICAL MAINS NETWORK...................................................................... 5
2.2 FRONT PANEL............................................................................................................................................. 6
2.3 REAR PANEL............................................................................................................................................... 6
2.4 PREPARING FOR MMA WELDING............................................................................................................. 7
2.5 PREPARING FOR TIG WELDING ............................................................................................................... 8
3 USER INTERFACE...................................................................................................................................... 9
4 UNIT POWER-UP ...................................................................................................................................... 10
5 RESET (LOAD FACTORY SETTINGS)..................................................................................................... 10
6 SET-UP (INITIAL SET-UP OF THE WELDING POWER SOURCE) ......................................................... 11
7 ALARM MANAGEMENT ........................................................................................................................... 13
8 WELDING ................................................................................................................................................. 14
8.1 MMA WELDING/MMA CEL ........................................................................................................................ 14
8.2 TIG DC WELDING ..................................................................................................................................... 16
8.3 TORCH TRIGGER PROCEDURE ............................................................................................................. 17
9 TECHNICAL DATA .................................................................................................................................... 18
10 ELECTRICAL DIAGRAM .......................................................................................................................... 20
10.1 REMOTE CONTROL CONNECTOR (back panel).....................................................................................22
11 SPARE PARTS .......................................................................................................................................... 23

WELD THE WORLD
Cod. 006.0001.1920
11/02/2021 V.2.2 Discovery 300
4
ENGLISH
1 INTRODUCTION
IMPORTANT!
This handbook must be consigned to the user prior to installation and commissioning of the unit.
Read the "General prescriptions for use" handbook supplied separately from this handbook before
installing and commissioning the unit.
The meaning of the symbols in this manual and the associated precautionary information are given in
the "General prescriptions for use”.
If the "General prescriptions for use" are not present, it is mandatory to request a replacement copy
from the manufacturer or from your dealer.
Retain these documents for future consultation.
LEGEND
DANGER!
This pictogram warns of danger of death or serious injury.
WARNING!
This pictogram warns of a risk of injury or damage to property.
CAUTION!
This pictogram warns of a potentially hazardous situation.
INFORMATION
This pictogram gives important information concerning the execution of the relevant operations.
 Thissymbolidentiesanactionthatoccursautomaticallyasaresultofapreviousaction.
 Thissymbolidentiesadditionalinformationorareferencetoadi󰀨erentsectionofthemanual
containing the associated information.
§ Thissymbolidentiesareferencetoachapterofthemanual.
*1 The symbol refers to the associated numbered note.
NOTES
Theguresinthismanualarepurelyguidelineandtheimagesmaycontaindi󰀨erenceswithrespectto
theactualequipmenttowhichtheyrefer.

WELD THE WORLD
Cod. 006.0001.1920
11/02/2021 V.2.2
Discovery 300
5
ENGLISH
1.1 INTRODUCTION
ThisprofessionalandruggedweldingpowersourceforDCMMAandTIGweldingwithexceptionalarc
characteristicsis designedtooperate inharshenvironmentalconditions intheelds ofprofessional
maintenance,shipyardsando󰀨shore,buildingconstructionandheavyfabrication.
Thecombinationofdigitalcontrolandexcellentweldingwithcellulosicelectrodesisidealforhydraulic
applicationsandweldingworkonoilpipelinesandinthepetrochemicalindustry.
Upto4mmdiameterelectrodeweldingispossibleinMMA.
InMMAweldingtheHotStartandArcForcefunctionsareadjustableandtheyallowimprovedarcstrik-
ing,aatterbeadandmoreuniformweld.
TheAntiStickingfunctionmakesitpossibletodetachtheelectroderapidlyfromtheworkpieceinthe
eventofaccidentalsticking.
Thefanisturnedononlyduringwelding,attheendoftheweldingprocessitremainsonforaxed
periodoftimeaccordingtoweldingconditions.
Thefanisnonethelesscontrolledbyspecicthermalsensorsthatguaranteeacorrectcoolingofthe
machine.
Accessories/ancillarydevicesthatcanbeconnectedtotheunit:
- Manualremotecontrollerforremoteadjustmentoftheweldingcurrent.
Consultyourdealerforanupdatedlistofaccessoriesandthelatestavailablenewproducts.
2 INSTALLATION
DANGER!
Lifting and positioning
Read the warnings highlighted by the following symbols in the “General prescriptions for use”.
2.1 CONNECTIONS TO THE ELECTRICAL MAINS NETWORK
Themainspowersupplyfeaturestowhichtheequipmentshouldbeconnectedaregiveninchapter“12
TECHNICAL DATA” at page 18.
Themachinecanbeconnectedtomotorgeneratorsprovidedtheirvoltageisstabilised.
Connect/disconnectthevariousdeviceswiththemachineswitchedo󰀨.

WELD THE WORLD
Cod. 006.0001.1920
11/02/2021 V.2.2 Discovery 300
6
ENGLISH
2.2 FRONT PANEL
1 2
○ Negativepoleweldingsocket[Item1].
○ Positivepoleweldingsocket[Item2].
2.3 REAR PANEL
1 432
○ Remotecontrollerconnector[Item1].
○ Powercable[Item2].
• Totallength(includinginternalpart):5,0m
• Numberandcrosssectionofwires:4x2.5mm2
• Powerplugtype:notsupplied
○ MainsprotectionONLED[Item3].ThisLEDilluminatesifanincorrectoperatingconditionoccurs:
• absenceofaphaseinthepowersupplyline.
○ WeldingpowersourceON/OFFswitch.Item4].

WELD THE WORLD
Cod. 006.0001.1920
11/02/2021 V.2.2
Discovery 300
7
ENGLISH
2.4 PREPARING FOR MMA WELDING
1. SettheweldingpowersourceON/OFFswitchto“O”(unitswitchedo󰀨).
2. Plugthepowercableplugintoamainssocketoutlet.
3. Choosetheelectrodebasedonthetypeofmaterialandthicknessoftheworkpiecetobewelded.
4. Insert the electrode in the electrode holder.
5. Connecttheelectrodeholdercabletotheweldingsocketbasedonthepolarityrequestedbythe
type of electrode used.
6. Connecttheplugofthegroundclamptotheweldingsocketonthebasisofthepolarityrequired.
7. Connecttheearthclamptotheworkpiecebeingprocessed.
DANGER!
Electric shock hazard!
Read the warnings highlighted by the following symbols in the “General prescriptions for use”.
8. SettheweldingpowersourceON/OFFswitchto“I”(unitpowered).
9. Selectthefollowingweldingmodeontheuserinterface:MMA
10.Settherequiredweldingparametervaluesontheuserinterface.
Whentheremotecontroller[RC]isconnectedandtherelativelockingscrewistightened,welding
currentcanbeadjustedusingtheremotecontroller.
Thesystemisreadytostartwelding.
REAR VIEW FRONT VIEW
(polarity to basic electrode)
RC

WELD THE WORLD
Cod. 006.0001.1920
11/02/2021 V.2.2 Discovery 300
8
ENGLISH
2.5 PREPARING FOR TIG WELDING
1. SettheweldingpowersourceON/OFFswitchto“O”(unitde-energized).
2. Plugthepowercableplugintoamainssocketoutlet.
3. Choosetheelectrodebasedonthetypeofmaterialandthicknessoftheworkpiecetobewelded.
4. Insert the electrode in the TIG torch.
5. Connectthetorchplugtotheweldingsocketonthebasisofthepolarityrequiredbythetypeof
electrode in question.
6. Connecttheplugofthegroundclamptotheweldingsocketonthebasisofthepolarityrequired.
7. Connecttheearthclamptotheworkpiecebeingprocessed.
8. SettheweldingpowersourceON/OFFswitchto“I”(unitpowered).
9. Selectthefollowingweldingmodeontheuserinterface:DCTIG
 Thismodelofweldingmachinehasnotbeenprovidedeitherwiththecontrolforgasow(solenoid
valve)orwiththetorchtrigger.
Thesystemisreadytostartwelding.
LIFT-ARC WELDING
1. Openthetorchvalvetoletthegasout.
2. Touchtheworkpiecewiththetorchelectrode.
3. Slowlyliftthetorchtostrikethearc.
TheWELDINGCURRENTreachesthepresetvalue.
4. Quicklydistancethetorchfromtheworkpiecetoextinguishtheweldingarc.
5. Closethetorchvalvetointerruptthegasow.
REAR VIEW FRONT VIEW
(polarity for tungsten electrode)
RC

WELD THE WORLD
Cod. 006.0001.1920
11/02/2021 V.2.2
Discovery 300
9
ENGLISH
3 USER INTERFACE
L1
L2
L3
L4
L6
L7
L8
L9
S1
S2 S3
POT1
POT2
E1
D1
CODE SYMBOL DESCRIPTION
L1 ThisLEDilluminatestoconrmthepresenceofpowerontheoutputsockets.
L2
Illuminationshowsthatthefollowingfunctionhasbeenactivated:VRD(reducedoutputvolt-
age).
The no-load voltage between the welding sockets is switched from U0 to Ur (see technical
data).
L3 Illuminatestoindicateavalueinthefollowingunitofmeasurement:AMPERES(A)
L4 Illuminatestoindicateavalueinthefollowingunitofmeasurement:VOLTS(V)
L6 This LED indicates that the current reference setting is imposed by the remote controller.
L7 ThisLEDilluminatestoshowthatthefollowingweldingmodeisselected:MMA
L8 ThisLEDilluminatestoshowthatthefollowingweldingmodeisselected:DESEAMINGMODE
L9 ThisLEDilluminatestoshowthatthefollowingweldingmodeisselected:CONTINUOUSDC
TIG
D1 Datasetting:Thedisplayshowstheacronymoftheparametertobeset.
Welding:Thedisplayshowsthee󰀨ectiveamperesorvoltsvalueduringwelding.
S1
Welding:Thisbuttonselectstheparametertobeshownonthefollowingdisplay:D1
Possiblechoices:(A)E󰀨ectiveweldingcurrent-(V)E󰀨ectiveweldingvoltage
Parameters/functionssetting:Thisbuttonselectstheparametertobeshownonthefollowing
display:D1
Possiblechoices:(A)E󰀨ectiveweldingcurrent-(V)E󰀨ectiveweldingvoltage
S2
Pressandrelease:thebuttonenablesthedevicetoreceivetheweldingcurrentcontrolsignal
from a remote controller.
Holddownfor3seconds:thebuttonactivatesaconnectedremotecontroller,ifavailable,which
isthenusedtomanageallfunctionsoftheweldingpowersourcefromadistance.

WELD THE WORLD
Cod. 006.0001.1920
11/02/2021 V.2.2 Discovery 300
10
ENGLISH
CODE SYMBOL DESCRIPTION
S3 Thisbuttonselectstheweldingmode.
POT1 MMA:Thepotentiometersetsthevalueofthefollowingparameter:HOTSTART
POT2 MMA:Thepotentiometersetsthevalueofthefollowingparameter:ARCFORCE
E1 Datasetting:Theencodersetsthevalueoftheselectedparameter.
Welding:Theencodersetsthevalueofthefollowingparameter:WELDINGCURRENT
4 UNIT POWER-UP
SettheweldingpowersourceON/OFFswitchto“I”toswitchontheunit.
AL.H.Themessageappearsonthefollowingdisplay:D1.
Firstpower-uporpower-upsfollowingaRESETprocedure
Theweldingpowersourcesetsupforweldingwiththefactorypre-sets.
Subsequentpower-ups
Theweldingpowersourcesetsupforweldinginthelateststableweldingcongurationthatwasactive
atthetimeofpower-o󰀨.
5 RESET (LOAD FACTORY SETTINGS)
L1
L2
L3
L4
L6
L7
L8
L9
S1
S2 S3
POT1
POT2
E1
D1
AA
ACTIVATION
Theresetprocedureinvolvescompleterestorationofthedefaultvalues,parametersandmemoryset-
tings set in the factory.
Theresetprocedureisusefulinthefollowingcases:
- Toomanychangesmadetotheweldingparameterssouserndsitdi󰀩culttorestoredefaults.
- Unidentiedsoftwareproblemsthatpreventtheweldingpowersourcefromfunctioningcorrectly.

WELD THE WORLD
Cod. 006.0001.1920
11/02/2021 V.2.2
Discovery 300
11
ENGLISH
A
○ SettheweldingpowersourceON/OFFswitchto“O”toswitchtheunito󰀨.
○Keeping both the S2 and S3 buttons pressed, set the generator power source
switchto“I”toturnontheequipment[ SIMULTANEOUS ACTIONS]
- rEC : Themessageappearsonthefollowingdisplays: D1.
- Wait for the memory clear procedure to terminate.
6 SET-UP (INITIAL SET-UP OF THE WELDING POWER SOURCE)
L1
L2
L3
L4
L6
L7
L8
L9
S1
S2 S3
POT1
POT2
E1
D1
AC
B
ACTIVATION/
SELECTION
EXIT
SETTING
A
○ SettheweldingpowersourceON/OFFswitchto“O”toswitchtheunito󰀨.
○Holding the S2 buttondown,turnthepowersourceswitchto“I”tostarttheequipment.
[ SIMULTANEAOUS ACTIONS]
- Vrd: The messageappearsonthefollowingdisplays:D1.
B○Using the encoder E1 ,editthevalueoftheselectedsetting.
C
○Exit with conrmation
- Press any button (except S2).
- Thisactionwillautomaticallyclosethemenu.
D
○Exit without conrmation
- Press the S2 button .
- Thisactionwillautomaticallyclosethemenu.
D

WELD THE WORLD
Cod. 006.0001.1920
11/02/2021 V.2.2 Discovery 300
12
ENGLISH
Tab. 1 - Parameters of the 2nd level menu: MMA mode
SETTING MIN DEFAULT MAX NOTES
OUTPUTVOLTAGEREDUCTION OFF OFF ON
LONGARCVOLTAGE 37 *SYN 65 Only MMA
*SYN:Thiscodeindicatesthatparametercontrolissynergic.Theoptimalvalueofthisparameteris
setautomaticallybythemicroprocessoronthebasisofthepre-setweldingcurrentvalue.
• WhenSYNisinstalled,todisplaythesynergicvaluepressthefollowingbutton:S1.
• Thisvaluecanbedisplayedbutitisnotuser-adjustable.
- OUTPUT VOLTAGE REDUCTION (VRD)
○ Thisparameterreducesthepotentialacrosstheweldingsocketswhenweldingisnotinprogress.
- The arc strike procedure is as follows:
• Touchtheworkpiecewiththeelectrodetip.
• Raise the electrode.
• Powerisreleasedforseveralseconds.
• Touchtheworkpiecewiththeelectrodetip.
• Theweldingarcwillstrike.
- LONG ARC VOLTAGE
○ Thisparameterinhibitspoweroutputwhenthepotentialbetweenelectrodeandworkpieceex-
ceedsthepre-setthresholdlevel.
- Consequences of a higher value:
• Theweldingarciskepttriggeredalsowiththeelectrodedetachedfromtheworkpiecebeing
soldered.
- Consequences of a lower value:
• Fasterexitfromweld.

WELD THE WORLD
Cod. 006.0001.1920
11/02/2021 V.2.2
Discovery 300
13
ENGLISH
7 ALARM MANAGEMENT
Analarmmessageappearsonthefollowingdisplay:D1.
Tab. 2 - Alarm messages
MESSAGE MEANING EVENT CHECKS
AL. HEA.
In start-up phase Appears for 2-3 seconds
Overheating alarm
Indicates tripping of the welding
powersourcethermalprotection.
Leavetheunitrunningsothatthe
overheated components cool as
rapidly as possible.
When the unit has cooled, the
welding power source will reset
automatically.
All functions disabled.
Exceptions:
• Cooling fan.
• Cooler(ifswitchedon).
• Make sure that the power re-
quiredbytheweldingprocessis
lower than the maximum rated
poweroutput.
• Check that the operating con-
ditions are in compliance with
the welding power source data
platespecications.
• Check for the presence of ade-
quate air circulation around the
weldingpowersource.
Phase missing alarm
Indicates the absence of a phase
inthepowersupplyline.
The message appears at the
same time as the mains protection
activationLEDswitcheson.
All functions disabled.
Exceptions:
• Cooling fan.
• Check if the equipment power
supply line has all the phases.
Iftheproblempersists:
• qualied technical personnel
are required for repair/mainte-
nancejobs.

WELD THE WORLD
Cod. 006.0001.1920
11/02/2021 V.2.2 Discovery 300
14
ENGLISH
8 WELDING
8.1 MMA WELDING/MMA CEL
L1
L2
L3
L4
L6
L7
L8
L9
S1
S2 S3
POT1
POT2
E1
D1
AACTIVATION
A
○Press the S3 buttontoactivatetheMMAorMMACELmode.
L7
L8
L9
S3 A
L 7 MMA
L 8 MMA CEL
Tab. 3 - Parameters of the 1st level menu: MMA/MMA CEL mode
SETTING MIN DEFAULT MAX NOTES
WELDING CURRENT
MAXIMUM CURRENT WITH REMOTE CONTROLLER 10 A 80 A 300 A MAX: Maximum value of welding current
HOT-START 0 % - 100 %
The value is calculated as a per-
centageofthepresetweldingcur-
rent.
ARC FORCE 0 % -
200 %
(MMA)
The value is calculated as a per-
centageofthepresetweldingcur-
rent.
400 %
(CEL) Thevalueislimitedto300Amax.

WELD THE WORLD
Cod. 006.0001.1920
11/02/2021 V.2.2
Discovery 300
15
ENGLISH
- WELDING CURRENT
○ Thisparameterregulatestheprimaryweldingcurrentvalue.
- MAXIMUM CURRENT WITH REMOTE CONTROLLER
○ Themaximumoutputcurrentvaluethatcanbeachievedwithfootpedalcontrollerexternalrefer-
ence.
- HOT-START
○This parameter aids electrode melting at the time of arc striking. It is set as a percentage referred
tothevalueofthefollowingparameter:WELDING CURRENT.
- Consequences of a higher value:
• Easeofactivation;Greaterstartingspatter;increaseintheactivationarea.
- Consequences of a lower value:
• Di󰀩cultyofactivation;Lessstartingsplatter;Reductionintheactivationarea.
- ARC FORCE
○ Thisparameterhelpstoavoidelectrodestickingduringwelding.Itissetasapercentagereferred
tothevalueofthefollowingparameter:WELDING CURRENT
- Consequences of a higher value:
• Fluencyfactorsinwelding;Arcweldingstability;Increasedmeltingoftheelectrodewithinthe
workpiece;Moreweldspatter.
- Consequences of a lower value:
• Thearcisextinguishedmoreeasily,lessweldingspatter.

WELD THE WORLD
Cod. 006.0001.1920
11/02/2021 V.2.2 Discovery 300
16
ENGLISH
8.2 TIG DC WELDING
L1
L2
L3
L4
L6
L7
L8
L9
S1
S2 S3
POT1
POT2
E1
D1
AACTIVATION
A
○Press the S3 buttontoactivatetheCONTINUOUSDCTIGmode.
L7
L8
L9
S3 A
L 9 CONTINUOUS DC TIG
Tab. 4 - Parameters of the 1st level menu: CONTINUOUS DC TIG mode
SETTING MIN DEFAULT MAX NOTES
WELDING CURRENT 5 A 80 A 300 A MAX: Maximum value of welding
current

WELD THE WORLD
Cod. 006.0001.1920
11/02/2021 V.2.2
Discovery 300
17
ENGLISH
8.3 TORCH TRIGGER PROCEDURE
- 2 STROKE LIFT:
○ Touchtheworkpiecewiththetorchelectrode.
○Press (1T) and keep the torch trigger pressed.
○ Slowlyliftthetorchtostrikethearc.
○ Theweldingcurrentreachesthepre-setvalue,bywayofanupslopetime,ifprogrammed.
○ Release(2T)thetriggertostarttheweldcompletionprocedure.
○ Thecurrentreachestheendcurrentvalueinthetimesetinthedownslopetimeparameter.
○ Thearcisextinguished.
○ Gasdeliverycontinuesforthetimesetinthepostgasparameter.
1St TIME 2nd TIME
LIFT
SLOPE UP DOWN SLOPE POST GASIGNITION
C.C.
CURRENT
STARTING
CURRENT
WELDING
CURRENT
FINAL
CURRENT

WELD THE WORLD
Cod. 006.0001.1920
11/02/2021 V.2.2 Discovery 300
18
ENGLISH
9 TECHNICAL DATA
Directives applied
Waste electrical and electronic equipment (WEEE)
Electromagnetic compatibility (EMC)
Lowvoltage(LVD)
Restrictionoftheuseofcertainhazardoussubstances(RoHS)
Construction standards EN60974-1;EN60974-10ClassA
Conformity markings
EquipmentcompliantwithEuropeandirectivesinforce
Equipmentsuitableinanenvironmentwithincreasedhazardofelectricshock
EquipmentcompliantwithWEEEdirective
EquipmentcompliantwithRoHSdirective
Supply voltage 3x400Va.c.±15%/50-60Hz
Mains protection 20A500VDelayed
Zmax
ThisequipmentcomplieswithIEC61000-3-12 provided that themaximumpermis-
siblesystemimpedanceislessthanorequalto38mΩattheinterfacepointbetween
the user’s supply and the public system. It is the responsibility of the installer or user
oftheequipmenttoensure,byconsultationwiththedistributionnetworkoperatorif
necessary,thattheequipmentisconnectedonlytoasupplywithmaximumpermis-
siblesystemimpedancelessthanorequalto38mΩ.
Dimensions ( L x D x H ) 460x230x325mm
Weight 20.8 kg
Insulation class H
Protection rating IP23
Cooling AF:Air-overcooling(fanassisted)
Maximum gas pressure 0,5 MPa (5 bar)
Static characteristic
MMA Falling characteristic
TIG Falling characteristic
MIG/MAG Flat characteristic
Welding mode MMA TIG
Current and voltage adjustment
range
10A/20.4V
300A/32.0V
5A/10.2V
300A/22.0V
Welding current / Working
voltage
40%(40°C) 300A/32.0V ---
50%(40°C) --- 300A/22.0V
60%(40°C) 230A/29.2V 250A/20.0V
100%(40°C) 200A/28.0V 210A/18.4V
Maximum input power
40%(40°C) 13.3kVA–10.7kW ---
50%(40°C) --- 10.3kVA–7.9kW
60%(40°C) 9.9kVA–7.9kW 8.4kVA–6.2kW
100%(40°C) 8.4kVA–6.6kW 6.7kVA–4.8kW
Maximum supply current
40%(40°C) 19.1 A ---
50%(40°C) --- 14.8 A
60%(40°C) 14.3 A 12.2 A
100%(40°C) 12.3 A 9.4 A

WELD THE WORLD
Cod. 006.0001.1920
11/02/2021 V.2.2
Discovery 300
19
ENGLISH
Maximum E󰀨ective Supply
Current
40%(40°C) 12.1 A ---
50%(40°C) --- 10.5 A
60%(40°C) 11.1 A 9.5 A
100%(40°C) 12.3 A 9.4 A
No-load voltage (U0) 76V
Reduced no-load voltage (Ur) 9V
Power source e󰀩ciency E󰀩ciency(300A/32,0V):85%
No-Loadconditionpowerconsumption(U1=400Va.c.):21,6W
Essential raw materials Accordingtotheinformationprovidedbyoursuppliers,thisproductdoesnotcontain
essentialrawmaterialsinquantitiesgreaterthan1gpercomponent.

WELD THE WORLD
Cod. 006.0001.1920
11/02/2021 V.2.2 Discovery 300
20
ENGLISH
10 ELECTRICAL DIAGRAM
050.000X.0134
1
F2 4A@
1
050.000X.0036
ROSSO-RED
NERO-BLACK
ROSSO-RED
050.000X.0031
JP6
12
J2
JP4
5
6423 1
J3
JP3
12
910
JP4
FLAT 10V
7864523
12
1
+
L
-
050.000X.0119
F1 4A@
HALL
3 421 9 10876 5
VIOLA-VIOLET NERO-BLACK
J4 J3
FLAT 10V
JP7
050.000X.0044
J2
J3J1
J1 J2
2
1
JP6
NERO-BLACK
VDC
M
VIOLA-VIOLET 24VAC
BIANCO-WHITE
BIANCO-WHITE
VIOLA-VIOLET
18VAC
18VAC
24VAC
GRIGIO-GREY
GRIGIO-GREY
30VAC
30VAC
400VAC
400VAC
JP1
050.000X.0038
050.000X.0039
F3 250mA@
F4 1A@
432
JP3
8
JP1
21 43 65 7
1
9 10
JP1
12
J2J1
MARRONE - BROWN
MARRONE - BROWN
MARRONE - BROWN
JP5
2 43
23 2
JP2
1 3
J1 J2 J3
NERO-BLACK
ROSSO-RED
ROSSO-RED
NERO-BLACK
NERO-BLACK
GIALLO_VERDE - YELLOW_GREEN
PE
050.000X.0057
6
JP2
2435
1
12
JP1
R
S
T
MAINS SWITCH
BLACK
J3
J2
BLACK
J1
BLACK
JP2
5 43 2 168 7
JP5
1234 65
ACBDEF
C
BA
D
E
F
PRES-PED
P-T/CONT-PED
GND-ISO
RIF-EXT
+10V-ISO
4321
3412
GIALLO_VERDE - YELLOW_GREEN
PE