Weelko F-330 User manual

MultiEquipment. Ref F-330
Instruction manual
5 IN 1
Magic Glove
Bio Skin Smoother
High Frequency
Ultrasound
Galvanic

Barcelona
Pol. Ind. La Valldan
Camí de Garreta, 86
08600 Berga
Barcelona – Spain
T. [phone]
E. [e-mail]
W. www.weelko.com
Warning Recycling
EC-Declaration of compilance Welcome!
Whenever any of our electrical products or their
presentation packaging bear this symbol, it means
that these products should not be treated as
conventional household waste in Europe. To ensure
proper treatment of this waste, dispose of it in
accordance with local laws or as required for the
disposal of electrical equipment. This initiative will
help preserve save natural resources and improve
standards of environmental protection in regard to the
treatment of electrical waste.
Thank you very much for purchase. Please read the
instructions carefully before operating the instrument.
You can also ask a professional for guidance to make
sure you are using the instrument correctly. We will
accept no responsibility for any accidents that occur
due to incorrect operation.
The company reserves the right to amend the details of
the instruments with no prior notice. If any mistakes
are found in these instructions, please feel free to
send us an e-mail informing us so that we can correct
them.
This product meets the following requirements:
1. Conditions set out in the Low Voltage Directive:
2006/95/EC
2. Conditions set out in the Electromagnetic Compati-
bility Directive: 2004/108/EC
•Never under any circumstances attempt to open or
inspect the internal components or accessories of the
machine. If an inspection becomes necessary, please
contact your supplier or a suitably competent
technician.
•Never use the unit in humid or poorly ventilated
environments, such as wet rooms, bathrooms etc. to
prevent damage to the electrical components of your
unit.
•Never use the unit outdoors; exposure to the
elements can cause damage.
•If the power cord was destroyed, please ask a
professional to service and replace it to avoid hazards,
or contact the dealer for service.

Instructions of use SKIN SCRUBBER
Front panel
1. Connect the power supply via the rear panel.
2. Connect the accessories properly to the front/rear
panel as indicated in the sketch.
3. Turn on the “POWER” button.
4. Press “FUNCTION” to select the desired function in
the following order: Skin Scrubber, Ultrasonic,
Galvanic, Magic Hand & Lifting.
1. Place the bracelet around the customer’s wrist.
2. Apply the appropriate conductive product
generously to the surface of the skin.
3. Select the desired wave type by pressing “STATE”,
the desired output energy by pressing “ENERGY” and
time of working by pressing “TIMER”. You can change
setting anytime during working.
4. Press “START/PAUSE” button to start. Once there is
circuit between the client and the scrubber, machine
will start to work. The Scrubber sign on the screen will
run when machine is working normally. Once there is
separation between the scrubber and the client,
machine will pause, and the Scrubber sign on the
screen will stop running.
F-330
4 in 1 beauty
instrument
Timer
Energy
State
function
select
Start/Pause
Notes Cautions
A positive earth control system is in place while the
machine is operating. This means that unless the
machine can find an earth return, the system will stop
the current output to the probe. However, once the
probe comes back into contact with the customer (the
earth circuit is found), the system will restart the
output immediately. This is a safety feature and
should not be mistaken for a system fault.
•The ones with the following diseases are required
not to use it: heart disease, infectious disease, a
person with metal in body due to treatment, a person
with extremely sensitive physical structure.
•Do not keep the probe at the same position of the
skin too long to avoid burning.
•In case the exclusive liquid is insufficient,
supplement it.
•As the probe is fitted and unloaded, please do it in
accordance with due order. Do not pull it off with
force.
•As the power wire is disconnected form the back,
pull it off from the socket. Do not pull its wire off.
•Do not hit the horn of the probe or damage the
stainless steel surface to avoid skin scratch.

ULTRASOUND
Before treatment
Cautions
Notes
1. Cleanse/tone the treatment area using the
prescribed skin-type products.
2. Remove any left-over product by facial steam for 10
minutes.
3. Cleanse the treatment area again to remove any dirt
or debris from the face in order to prevent the
ultrasound waves from pushing it back into the dermis.
4. Tone every part of the face (or treatment area)
gently using a suitable astringent.
5. After wiping off the astringent, the skin will be
thoroughly cleansed for optimum protection.
6. Apply enough conductive gel to the treatment area.
Starting treatment
1. Select the desired ultrasonic probe by pressing
“SELECT”, wave type by pressing “STATE”, the desired
output energy by pressing “ENERGY” and time of
working by pressing “TIMER”. You can change setting
anytime during working.
2. Press “START/PAUSE” button to start.
•Always make sure enough conductive gel is applied
for at least 15 minutes of treatment time.
•Generally, lower outputs are used for facials and
higher outputs for body treatments.
•If the treatment area is small or sensitive, use the
eye probe and make sure that the energy output is
limited to 5-7 blocks (on the “ENERGY” LCD screen
display). The treatment time may also be reduced to
8-10 minutes.
•A standard treatment course lasts around 10
sessions in total, with a minimum resting period of 1
day between sessions. If other facial treatments are
being conducted on the same area, a minimum rest
period of 7 days should be observed between
treatments.
•Never use on dry skin.
•Do not use on the stomach area of pregnant women.
•Do not use on people with pace-makers (any
electrical or rhythmic heart-regulating device).
•Do not use on people with known heart conditions.
•Always use ultrasonic electrodes with enough
moisturizer or serum on the skin.
•Ultrasonic treatment is suitable for all skin types.
The massage time and machine settings can be
adjusted for each different skin type. For sensitive
skins, reduce treatment time to 3-5 minutes and make
sure the power setting is at the lowest level to start
with.

GALVANIC
Before treatment
Cautions
Contraindications
1. The treatment area must be washed and dried
before any products can penetrate into the tissue.
2. The polarity of the probes can be changed by
adjusting the “STATE” button between (+R) or (-G).
3. Cover the roller/ball with a piece of cotton or a
sponge that has been dipped into a suitable lotion
(according to the treatment). The lotion can also be
applied directly to the skin.
Starting treatment
1. Choose the desired galvanic probes (roller or ball).
Then properly connect two identical probes in the
wires.
2. Select the desired polarity by pressing “STATE”, the
power output level must be at the minimum and select
the desired time of working by pressing “TIME”. You
can change any of these settings during the treatment.
3. Press the “START/PAUSE” button.
•Pacemaker (any electrical or rhythmic
heart-regulating device)
•Pregnancy
•Thrombosis/Phlebitis
•Skin diseases
•Operations (within the last 6 months)
•Silicone implants
•Hypersensitive or vascular skin
•Always make sure customers remove any jewelry,
and confirm that they have not had any metal implants
(pins, joints, etc.) installed since their last treatment.
•Pregnant women and people with sensitive, injured,
inflamed skin or blood capillary expansions should not
receive this treatment.
•Customers with health issues such as heart disease
or infectious diseases and hyper-allergic or
hyper-sensitive skin (see contra-indications) may not
use this instrument.
•Always make sure the skin surface has been
moistened with plenty of conductive product.

MAGIC GLOVES
Instructions of use
Cautions
Notes
1. Connect ones side of the wire in the rear panel, in
the plug named “BIO WAVE MICROCURRENT”.
2. Connect the other two sides of the wires in each
glove.
3. The beautician must put isolating gloves under the
magic gloves.
3. Select the magic glove function by pressing
“FUNCTION” button.
3. Make sure that the “ENERGY” level is at the
minimum. You can adjust the output level by pressing
“ENERGY +/-”.
3. Make sure that the “FREQUENCY” level is adjusted
at 0.1 Hz. You can adjust the frequency level by
pressing “SATE”.
3. Select the desired wave state by pressing
“SELECT”. There are 4 kinds of waves.
3. Select the time of operating by pressing “TIMER
+/-”.
3. Press “START/PAUSE” to start the treatment.
3. The beautician must massage to beautician with the
magic gloves. Adjust the “ENERGY” and “FREQUENCY”
level according to the customer feelings. At this
moment, the beautician don’t have to feel any effect in
their hands, but the customer must feel a micro
current and some warm in the part where the
treatment are applied.
•The delivered magic gloves have a length of 20 cm.
The isolating gloves must have a length of at least 23
cm. If there are contact between the beautician’s skin
and the magic gloves, there’s no effect with the
treatment.
•During the treatment, if the beautician breaks the
contact with the customer’s skin, the device stops
working suddenly. The device restarts when the
contact between the magic gloves and the customers
skin returns.
•Pacemaker (any electrical or rhythmic
heart-regulating device)
•Pregnancy
•Thrombosis/Phlebitis
•Skin diseases
•Operations (within the last 6 months)
•Silicone implants
•Hypersensitive or vascular skin

BIO-LIFTING
Instructions of use
1. Connect ones side of the wire in the rear panel, in
the plug named “BIO WAVE MICROCURRENT”.
2. Connect the other two sides of the wires in the
handles of BIO-lifting. There are two kinds of handles.
•The ones that need cotton swabs are used in the
eyes part. Is needed to include two cotton swabs in
the hole of the handle.
•The ones with only one pole are used to the full
body.
3. Apply enough conductive gel to the treatment area.
4. Make sure that the “ENERGY” level is at the
minimum. You can adjust the output level by pressing
“ENERGY +/-” button.
5. Make sure that the “FREQUENCY” level is adjusted
at 0.1 Hz. You can adjust the frequency level by
pressing “SATE”.
6. Select the desired wave state by pressing
“SELECT”. There are 4 kinds of waves.
7. Select the time of operating by pressing “TIMER
+/-”.
8. Press “START/PAUSE” to start the treatment.
Ultrasound
Check the following if the work unit switches on but
the probes do not emit.
•Put a drop of water on one probe.
•Switch on the unit and slowly increase the output
energy.
•If the water starts to move and evaporate, the unit
and the probes are working properly. If not, the probes
are not working properly.
The unit and the probes are working properly but the
customer doesn’t feel any effects.
•Make sure enough conductive gel has been applied
to the treatment area.
FAQ
Skin scrubber
The probe suddenly stops emitting:
•If the probe is separated from the skin, it will stop
emitting after 5 seconds. This is a safety feature and
should not be mistaken for a system fault.
•Touch the skin with the probe and it will start
emitting again after 5 seconds.

Galvanic
Magic gloves & BIO-lifting
•Take care not to damage the probe rollers. Never use
abrasive substances to clean the probe rollers, since
damage to the surface of the roller may scratch the
surface of the skin during treatment; any damaged
areas may also harbor bacteria and make sterilization
more difficult.
•After treatment, all metal roller parts must be
cleaned, sterilized and dried. Then store them in the
accessory holder to avoid any damage.
•After each treatment, the magic gloves and the
BIO-lifting handles must be cleaned, sterilized and
properly saved in a dry place.
MAINTENANCE
Skin scrubber
•Any oil on the probe must be removed immediately.
•After use, please clean the probe and keep it probe.
Store it in the probe-protecting sleeve at all time.
•Store the probe carefully to avoid damaging it.
Ultrasound
•The ultrasound probes should be cleaned using
clean water (not hot) and a clean, soft cloth and then
chemically sterilized using an appropriate sterilization
fluid. Dry the probe carefully after sterilizing and store
it safely in its holder on the trolley in between uses.
Always sterilize the probes again prior to use.
•Never immerse the probe in any fluid!