Welbilt Frymaster Dean SDU Series User manual

Turn the fryer off. Skim debris from the oil. Retrieve SDU from storage. Ensure SDU is empty and the crumb
tray is clean. Ensure the oil is below 120oF.
Attach drain extension. Position SDU under drain extension. Open drain valve; drain oil into SDU;
close drain valve. Remove and store
drain extension.
Carefully roll SDU from fryer; remove
and empty crumb tray.
Replace crumb tray and latch SDU lid.
Move SDU to oil disposal site. Rotate spout to disposal container. Attach hose or place funnel in oil disposal
container opening. Turn pump handle
toward spout to pump out oil.
(No flow. See troubleshooting section.)
SDU Operation for Fryers Without Built-In Filtration: Step-by-Step Guide
1 2 3 4 5
6 7 8 9 10
11 13 14
Bulletin # 818-0608 7/20
Hot frying oil and equipment can cause severe burns. They must be handled with care to avoid such injury caused by improper handling techniques or
inadequate protective gear. Be sure to wear all appropriate safety gear as directed in store operating manual when handling hot frying oil or equipment.
Release locking pin on pump head.
12
Return SDU to storage.
15
SDU: A Good Turn for Your Exhausted Oil Prime Before First Use, After Lengthy Non-Use
Troubleshooting Potential O-Ring Problems
Remove the pump and pipe unit from
the SDU by lifting up.
Invert pump and pour 1 cup of clean
cooking oil into the pipe.
With the pump inverted turn the handle
clockwise 3-4 turns stopping before oil
pumps out of the spout.
Reseat the pump and pipe unit on
the SDU.
1. Unseat the pump and pipe unit
and allow it to rest in the open tank.
2. Crank the pump.
3. If the oil flows, the O-ring seals
on the pump pipe have failed
and must be replaced.
12
43
SDU Do’s
• Prime pump for initial use and
after periods of non-use.
• Empty crumb tray and tank
after each use.
• Ensure oil is ≤ 120º F before
draining into SDU.
SDU Don’ts
• Don’t drain water or boil-out solution into
SDU tank.
• Don’t use without crumb tray.
• Don’t leave oil or shortening in SDU tank.
• Don’t pump hot oil > 120º F into SDU tank.
• Don’t move SDU with lid unlatched.
Rotate crank clockwise
to dispose of oil.
These instructions are intended as a quick reference. Read the manual, which
accompanied this product, and follow all safety guidelines.
Operating pump with oil hotter than
recommended temperature will void
pump warranty.
TO ORDER MORE FILTRATION SUPPLIES PLEASE CALL
1-800-221-4583 or visit www.frymaster.com
8700 Line Avenue
Shreveport, LA 71106-6814, USA
318-865-1711, fax [phone]
© Frymaster 2020 Printed in the U.S.A.

Turn the fryer off. Skim debris from the oil. Retrieve SDU from storage. Ensure SDU is empty and the crumb
tray is clean.
Ensure the oil is below 120oF.
Remove the filter pan. Slide SDU under filter drain down-spout. Open drain valve; drain oil into SDU;
close drain valve.
Carefully roll SDU from fryer; remove
and empty crumb tray.
Replace crumb tray and latch SDU lid.
Move SDU to oil disposal site. Rotate spout to disposal container. Attach hose or place funnel in oil disposal
container opening. Turn pump handle
toward spout to pump out oil.
(No flow. See troubleshooting section.)
SDU Operation for Fryers With Built-In Filtration: Step-by-Step Guide
12345
6 7 8 9 10
11 13 14
Bulletin # 818-0608 7/20
Hot frying oil and equipment can cause severe burns. They must be handled with care to avoid such injury caused by improper handling techniques or
inadequate protective gear. Be sure to wear all appropriate safety gear as directed in store operating manual when handling hot frying oil or equipment.
Release locking pin on pump head.
12
Return SDU to storage.
15
SDU: A Good Turn for Your Exhausted Oil Prime Before First Use, After Lengthy Non-Use
Troubleshooting Potential O-Ring Problems
Remove the pump and pipe unit from
the SDU by lifting up.
Invert pump and pour 1 cup of clean
cooking oil into the pipe.
With the pump inverted turn the handle
clockwise 3-4 turns stopping before oil
pumps out of the spout.
Reseat the pump and pipe unit on
the SDU.
1. Unseat the pump and pipe unit
and allow it to rest in the open tank.
2. Crank the pump.
3. If the oil flows, the O-ring seals
on the pump pipe have failed
and must be replaced.
12
43
These instructions are intended as a quick reference. Read the manual, which
accompanied this product, and follow all safety guidelines.
SDU Do’s
• Prime pump for initial use and
after periods of non-use.
• Empty crumb tray and tank
after each use.
• Ensure oil is ≤ 120º F before
draining into SDU.
SDU Don’ts
• Don’t drain water or boil-out solution into
SDU tank.
• Don’t use without crumb tray.
• Don’t leave oil or shortening in SDU tank.
• Don’t pump hot oil > 120º F into SDU tank.
• Don’t move SDU with lid unlatched.
Rotate crank clockwise
to dispose of oil.
Operating pump with oil hotter than
recommended temperature will void
pump warranty.
TO ORDER MORE FILTRATION SUPPLIES PLEASE CALL
1-800-221-4583 or visit www.frymaster.com
8700 Line Avenue
Shreveport, LA 71106-6814, USA
318-865-1711, fax [phone]
© Frymaster 2020 Printed in the U.S.A.