Well SEC WL1014 User manual

GSM LCD Alarm System
WL1014
User Manual
Date Issued: 2011-01-08

Well SEC Electronic Co., Ltd Http://www.wellsecurityalarm.com
Page １of 35 Ver 2.1
Thank you for purchasing this alarm system. For proper use and your
safety, please read these instructions thoroughly and carefully before you
put the system in use. Keep this manual carefully for your reference in the
future.
Warning
Do not remove the front or back cover of the unit and keep it intact.
There is no part that can be repaired by user. If repair is needed,
please send it to seller or authorized service point.
The information contained in this manual is prepared for the alarm
system only. It adopts a sustainable development strategy.
Therefore, the company retains the right to modify or make
improvement to any product described herein without giving prior
notice. All rights reserved. The name of other companies or
products referred to herein may be the brand or product name of
their respective owners.
Precautions
Please read and follow the brief instructions below, otherwise physical
danger or system damage may be incurred. This manual contains more
detailed information about safety issues concerning the system in other
parts hereof.

Well SEC Electronic Co., Ltd Http://www.wellsecurityalarm.com
Page ２of 35 Ver 2.1
Proper use Read this manual carefully before you
put he system in use.
Operate in accordance with the
instructions herein.
Water-proofness The alarm system is not
waterproof. Please keep it dry.
Qualified maintenance Only those qualified maintenance
service professionals may repair the
alarm system.
Backup Be sure to back up all important
information stored in the system.
Original parts and Only original parts and batteries
batteries approved by manufacturer may be
used, otherwise the warranty
term may be breached and
danger may occur.

Well SEC Electronic Co., Ltd Http://www.wellsecurityalarm.com
Page ３of 35 Ver 2.1
Addition of other Before adding other equipment, please
equipment read the user manual for detailed safety
instructions. Be sure not to connect
incompatible products to the system.
Switch on safety Do not switch the Device on when
wireless phone use is prohibited or when
it may cause interference or danger.
Interference All wireless devices may be susceptible
to interference, which could affect
performance.
Switch off in Follow any restrictions. Switch the device
restricted areas off in aircraft, near medical equipment,
fuel, chemicals, or blasting areas.

Well SEC Electronic Co., Ltd Http://www.wellsecurityalarm.com
Page ４of 35 Ver 2.1
Table of contents
1. Brief introduction ----------------------------------------------------6
2. Standard Packing list ----------------------------------------------6
3. Function Introduction ----------------------------------------------6
4. Alarm Host Diagram -----------------------------------------------7
5. Installation ------------------------------------------------------------9
5.1 Insert SIM into Control Unit----------------------------------9
5.2 Install the Magnetic door/window sensors---------------10
5.3 Install the wireless PIR Motion Sensor-------------------11
5.4 Install other sensors------------------------------------------12
5.5 Install the Control Unit----------------------------------------12
5.6 Siren and wireless outdoor siren--------------------------12
6. Setting-----------------------------------------------------------------13
6.1 Enter Settings-------------------------------------------------13
6.2 Exit Settings---------------------------------------------------14
6.3 Factory Reset-------------------------------------------------14
6.4 Remote controller--------------------------------------------14
6.5 Defense zone-------------------------------------------------15
6.6 Change pass ward-------------------------------------------16
6.7 Clock Setting--------------------------------------------------17
6.8 Timing Settings-----------------------------------------------18
6.9 Call alert target phone number---------------------------19
6.10 SMS Alert Target cell phone number-----------------20
6.11 Defense Zone Programming----------------------------21
6.12 Home Arm Defense Zone Setting----------------------22
6.13 Voice Recording--------------------------------------------22
6.14 Siren Setting-------------------------------------------------23
6.15 Siren Setting in “Emergency Help” mode------------23
7. Operation Instructions --------------------------------------------23
7.1 Remote Controller Operation-------------------------------24
7.2 Answer Alarm Call--------------------------------------------26
7.3 Remote Control------------------------------------------------26

Well SEC Electronic Co., Ltd Http://www.wellsecurityalarm.com
Page ５of 35 Ver 2.1
7.4 System Dialing Function-------------------------------------27
8. Technical Parameters---------------------------------------------28
9. Care--------------------------------------------------------------------30
10. Add/Cancel wireless sensors to the Control Unit-----------31
11. Technical specifications of Control Unit-----------------------32
12. Important information----------------------------------------------32
13. Maintenance --------------------------------------------------------33
14. Warranty--------------------------------------------------------------33

Well SEC Electronic Co., Ltd Http://www.wellsecurityalarm.com
Page ６of 35 Ver 2.1
1. Brief introduction
The WL1014 is an innovative safety solution for home, office and industry.
It integrates GSM network, SMS Control, voice, wireless communication
and proprietary technologies. It is suitable for a wide range of applications.
2. Contents
Standard Packing List:
Control Unit
Magnetic Door Sensor
Two Wireless Remote Controls
PIR Motion Sensor
Mini Siren
Regulated 12vDC Power Supply
User Manual
Optional Accessories:
Combined Light and Siren
PIR Motion Sensor
Glass Break Sensor
Magnetic Window Sensor
Magnetic Steel Scrolling Door Sensor
Temperature Sensor
Oil Pressure electronic Sensor
Infrared Beam Fence
3. Function Instruction
1) 7 wired and 99 wireless defense zones;
2) LCD screen with time clock display;
3) Voice prompt for all operations;
4) 3 groups of timely arm and disarm;
5) Can store 6 phone numbers: when alarming, system will make alarm
call to these numbers automatically;
6) Can store 3 SMS numbers: when alarming, system will send alarming
SMS automatically;

Well SEC Electronic Co., Ltd Http://www.wellsecurityalarm.com
Page ７of 35 Ver 2.1
7) 10-second automatic message recording;
8) Built-in artificial intelligent digital voice announcer;
9) Built-in artificial intelligent English message;
10) Users can make calls by using keypad on alarm panel, just ike a
telephone;
11) One-key-control function: Out Arm, Home Arm, Remote Arm;
12) SOS, fire, gas, door, hall, window, balcony, and boundary places alarm;
13) Real-time, delay, 24 hours, bypass defense zones programming
function;
14) Wireless coding: easy to add additional wireless accessories;
15) Remote control Arm, Disarm, Monitor, and Intercom by hone;
16) SMS alert for power failure or recovery;
17) Built-in AAA NI-HI rechargeable battery: make alarm when power off.
4. Alarm Host Diagram
In order to make the main unit get the wireless signal well for all wireless
accessories, please put the alarm host at the central place of your defense
area. Make sure it’s away from large metal objects and household
appliances which may cause high frequency interference, as well as
barriers such as reinforced concrete wall or fire door, etc.
Alarm Panel front schematic diagram:

Well SEC Electronic Co., Ltd Http://www.wellsecurityalarm.com
Page ８of 35 Ver 2.1
Alarm Panel back schematic diagram:
Wired terminal block:
LCD display:

Well SEC Electronic Co., Ltd Http://www.wellsecurityalarm.com
Page ９of 35 Ver 2.1
5. Installation
5.1 Insert SIM into Control Unit
Please see the below photos:
Please insert SIM card and plug in power adaptor, and then power on the
system, all the LED lights will be on for 2 seconds and you will hear a long

Well SEC Electronic Co., Ltd Http://www.wellsecurityalarm.com
Page １０ of 35 Ver 2.1
beep; the system comes into initialization. After the time clock displays on
the LCD screen, the [SGM] starts flashing and the main unit starts to detect
the GSM network until a long beep. Then the [SGM] indicator goes out
indicating the system comes into disarm status. Finally, turn on the backup
battery switch.
5.2 Install the Magnetic door/window sensors
Magnetic door/window sensors signal the Control Unit when the two parts
separate by more than between 1.5 to 3.0cm.
In some circumstances an Infrared beam fence is more appropriate than
magnetic sensors. i.e. veranda, picture window balcony, boundary wall
e.t.c.
Wired or wireless glass break sensor can also be used (see below)
For a Scrolling Steel Door, a special Wireless Scroll Steel Door magnetic
sensor, must be used due to interference of the wireless signal caused by
the steel door.

Well SEC Electronic Co., Ltd Http://www.wellsecurityalarm.com
Page １１ of 35 Ver 2.1
Installation: attach the larger half to the floor and attach (rivet or glue) the
smaller half to the scroll steel door. An alarm is triggered when the halves
are separated by more than three to 5.00 cm.
ScrollSteelDoor
5.3 Install the wireless PIR Motion Sensor
The PIR sensor will detect a person since human temperature is different to
ambient temperature. When triggered, the PIR will signal the Control Unit.
Apply the detection area illustration below when installing.
Wireless curtain sensor, detection area illustration below:

Well SEC Electronic Co., Ltd Http://www.wellsecurityalarm.com
Page １２ of 35 Ver 2.1
5.4 Install other sensors
For smoke, you can use wireless smoke sensor, for gas leakage detection,
you can install gas leakage sensor below
For temperature, you can install the temperature sensor below:
5.5 Install the Control Unit
In order to avoid destruction of the Control Unit by intruders, please install it
in a concealed location, convenient to the operator.
If applicable, ensure that an uninterruptible AC power outlet is available
near the Control Unit. First connect accessories to the Control Unit then the
AC adapter.
5.6 Siren and wireless outdoor siren
Connect the Siren and the intercom to the Control Unit and fix them in
appropriate locations .
1)Mini Siren

Well SEC Electronic Co., Ltd Http://www.wellsecurityalarm.com
Page １３ of 35 Ver 2.1
2) Wired strobe siren
3) wireless outdoor siren
Wiring Diagram of Outdoor siren for WL1014
6. Settings
6.1 Enter Settings
In the state of disarm, input 4-digit password by the keypad on the main
unit and press [#] button to confirm. You will hear a voice prompt: please
enter instruction. At the same time, [SET] indicator is on without flashing
and [0000] displays on the screen, indicating the system enters setting
status. You can perform different settings repeatedly as long as the system
keeps in setting status. The system will exit setting mode and return to
disarm status if you don’t press any keypad button for 40 seconds.
Note: In setting status, press can delete the numbers input.
The system default password is [8888].
Operating method: [XXXX]➩[#]
X indicates the new 4-digit password.
LCD display:

Well SEC Electronic Co., Ltd Http://www.wellsecurityalarm.com
Page １４ of 35 Ver 2.1
6.2 Exit Settings
Press [*] and [#] buttons, the main unit emits a long beep and exits
settings. The [SET] indicator goes out and the system returns to disarm
state.
Operating method: 【*】➩【#】
6.3 Factory Reset
In disarm status, use keypad to input [95175308246] and press [#] to
confirm, all the LED indicators will be on for 2 seconds and you will hear a
long beep. The main unit gets all its settings cleared and restores to its
factory settings successfully.
Operating method: [95175308246] + [#]
6.4 Remote controller
6.4.1 Coding of Remote Controller
The remote controller has to be code to the alarm host in order to
perform normally.
In setup state, use keypad to input [20], input the remote controller number
[1~8], and then press [#] to confirm. The main unit emits a long beep and
you will hear “remote control coding”. The [ ] indicator is on without
flashing; press any button on the wireless remote controller, the main unit
makes a long beep and you will hear “coding completed”,[ ] indicator
goes out, indicating the remote controller succeeds in coding.
Operating method: [20]➩[A]➩[#]
A indicates: 1~8 remote controllers number. You can add maximum 8

Well SEC Electronic Co., Ltd Http://www.wellsecurityalarm.com
Page １５ of 35 Ver 2.1
remote controllers.
LCD display:
4
6.4.2 Delete Remote Controller
The remote controller can’t control the main unit after it’s deleted.
In setup state, use keypad to input [21], then input the remote controller
number [1-8], and then press [#] to confirm. The main unit emits a long
beep and the [Signal] indicator flickers once. You will hear a voice
prompt “delete completed”.
Operating method: [21]➩[A]➩[#]
A indicates: 1~8 remote controllers number.
6.5 Defense zone
6.5.1 Coding of defense zone
Wireless detectors have to be coded to the main unit in order to trigger it
alarms.
In setup state, use keypad to input [23], input the defense zone number you
want to code [01~99], and then input [#] to confirm. The main unit emits a
long beep and the corresponding defense zone is displayed on the screen.
You will hear a voice prompt “detector coding”. Then trigger a wireless
detector to emit a wireless signal; after receiving the signal, the main unit
makes a long beep, and you will hear “coding completed”, the [ ]
indicator goes out at the same time.
Operating method: [23]➩[XX]➩[#]
XX indicates: 01 ~99 defense zones number
LCD display:

Well SEC Electronic Co., Ltd Http://www.wellsecurityalarm.com
Page １６ of 35 Ver 2.1
6.5.2 Delete Defense Zone
The wireless detector can’t control the main unit after it’s deleted.
In setup state, use keypad to input [24], then input the defense zone
number you want to delete [01~99], and then input [#] to confirm. The main
unit emits a long beep and the defense zone indicator flickers once. You
will hear a voice prompt “delete completed”.
Operating method: [24]➩[XX]➩[#]
XX indicates: 01 ~99 defense zones number
6.6 Change passward
6.6.1 Change Operation Password
Operation password is the password used to disarm or remote control.
In setup status, use keypad to input [30], then input the 4-digit new
password, and then press [#] to confirm. The main unit will make a long
beep and you will hear a voice prompt “setting completed”.
Operating method: [30]➩[XXXX]➩[#]
XXXX indicates: the new 4-digit password
For example: change the system password to 1012
Operating method: [30]➩[1012]➩[#]
LCD display:
6.6.1 Change Program Password
Program password is the password you should input in order to setup the
system.

Well SEC Electronic Co., Ltd Http://www.wellsecurityalarm.com
Page １７ of 35 Ver 2.1
In setup status, use keypad to input [31], then input the 4-digit new
password, and then press [#] to confirm. The main unit will make a long
beep and you will hear a voice prompt “setting completed”.
Operating method: [31]➩[XXXX]➩[#]
XXXX indicates: the new 4-digit password
For example: change the system password to 2846
Operating method: [31]➩[2846]➩[#]
LCD display:
Note：the operation password and the programming password can not
be set as the same number.
6.7 Clock Setting
In setup status, use keypad to input [32], then input the last 2 digits [AA] of
the present year, the two digits [BB] of the month, the two digits [CC] of the
date, the two digits [DD] of the hour (24-hour system), the two digits [EE] of
the minute, the two digits [FF] of the second, and finally enter [#] to confirm.
You will hear a long beep and a voice prompt “setting completed”.
Operating method: [32]➩[AA]➩[BB]➩[CC]➩[DD]➩[EE]➩[FF]➩[#]
AA indicates: the last 2 digits of the present year
BB indicates: the 2 digits of the present month
CC indicates: the 2 digits of the present date
DD indicates: the 2 digits of the present hour
EE indicates: the 2 digits of the present minute
FF indicates: the 2 digits of the present second
For example: set the time as 15:35:40, Oct. 1st, 2009
Operating method: [32]➩[09]➩[10]➩[01]➩[15]➩[35]➩[40]➩[#]

Well SEC Electronic Co., Ltd Http://www.wellsecurityalarm.com
Page １８ of 35 Ver 2.1
6.8 Timing Settings
6.8.1 Timely Arm
In setup status, use keypad to input [33~35], then input the hour [AA] and
minute [BB] of the time you want to set to arm, and finally input [#] to
confirm. You will hear a long beep and a voice prompt “setting completed”.
Operating method: [XX]➩[AA]➩[BB]➩[#]
XX indicates: the address code 33, 34, 35 of the timely arming
AA indicates: the hour of the setting time
BB indicates: the minute of the setting time
For example: set the arm time as 45’ 10pm
Operating method: [33]➩[22]➩[45]➩[#]
LCD display:
6.8.2 Timely Disarm
In setup status, use keypad to input [36~38], then input the hour [AA] and
minute [BB] of the time you want to set to disarm, and finally input [#] to
confirm. You will hear a long beep and a voice prompt “setting completed”.
Operating method: [XX]➩[AA]➩[BB]➩[#]
XX indicates: the address code 36, 37, 38 of the timely disarming
AA indicates: the hour of the setting time
BB indicates: the minute of the setting time
For example: set the arm time as 55’ 7am
Operating method: [33]➩[22]➩[45]➩[#]
LCD display:

Well SEC Electronic Co., Ltd Http://www.wellsecurityalarm.com
Page １９ of 35 Ver 2.1
6.8.3 Timing Control
In setup status, use keypad to input [39], then input the number indicating
turning on timely arm/ disarm [1/0], and then input [#] to confirm. You will
hear a long beep and a voice prompt “setting completed”. The factory
default is off.
Operating method: [39]➩[0/1]➩[#]
0: turn off the function of timely arm/ disarm
1: turn on the function of timely arm/ disarm
For example: turn on the function of timely arm/ disarm
Operating method: [39]➩[1]➩[#]
6.9 Call alert target phone number
6.9.1 Set alert target phone number
In setup state, input [51] ~ [56], then input the voice alarm-receiving
number (mobile number or telephone number), and then press [#] to
confirm. The main unit will make a long beep, the [Signal] indicator will
flicker once, and you will hear “setting completed”, which indicate voice
alarm-receiving number is set successfully.
Operating method: [XX]➩[YY…YY]➩[#]
XX indicates: the 1- 6 alarming user number [51] ~ [56]
YY…YY indicates: voice alarm-receiving phone number
For example: set 13811111111 as the first voice call number
Operating method: [51]➩[13811111111]➩[#]
LCD display: