Werner ALDEK User manual

ALDEK®ALUMINUM SCAFFOLD
ASSEMBLY
INSTRUCTIONS

Lock casters on one end frame by depressing
foot brake. Attach frame lock of horizontal brace to the
outside vertical post of the end frame just above the sec-
ond horizontal from the top.
Lock casters on remaining end frame and
raise to vertical position. Attach the opposite end of the
horizontal brace to the remaining end frame at the same
height on the vertical post.
Place platform at the desired height by placing
hooks of platform on end frame horizontals.
Place horizontal braces at the appropriate
level for use as guard rails by attaching frame locks to
end frame horizontals. Remove all people and material and
final level using adjustable legs. Read and understand all
instructions on scaffold and scaffold platform before use.
Check Federal, State, and Local Codes regarding use of
outriggers, toe boards, and guard rails or consult
the manufacturer.
8.
3. 4.
Attach frame lock of horizontal-diagonal brace to
the vertical post of one end frame just above the bottom
horizontal. Attach the opposite end of the horizontal-diagonal
brace to the opposite vertical post of the other end frame at the
same height. Repeat with the other horizontal-diagonal brace
to form a horizontal "X" as shown.
Lock all adjustable leg assemblies and run
safety nuts up snugly against locking collar.
Pre-level end frames by unlocking adjustable leg
assemblies and extending the legs equally.
Attach frame lock of diagonal brace to
horizontal of opposite end frames so that one end is two
horizontals above or below the other. Repeat with the
other diagonal brace to form a vertical "X" as shown.
1.
5. 6.
2.
ALDEK® Wide Span Aluminum Scaffold Base Section Assembly Instructions
Lock casters on remaining end frame and raise
to vertical position. Attach the opposite end of the
horizontal brace to the remaining end frame at the same
height on the vertical post.
Lock casters on one end frame by depressing
foot brake. Attach frame lock of horizontal brace to the out-
side vertical post of the end frame just above the second hori-
zontal from top.
Lock all adjustable leg assemblies and run
safety nuts up snugly against locking collar.
Place platforms at desired height by placing
hooks of platforms on end frame horizontals.
Attach frame lock of diagonal brace to
horizontal of opposite end frames so that one end is two
horizontals above or below the other. repeat with the
second diagonal brace to form a vertical "X" as shown.
Repeat procedure with remaining pair of diagonal braces
on the other side of base section.
Attach frame lock of horizontal-diagonal brace
to the vertical post of one of the of the end frames just above
the bottom horizontal. Attach the opposite end of the
horizontal-diagonal brace to the opposite vertical post of the
other end frame at the same height. Repeat with the other
horizontal-diagonal brace to form a horizontal "X" as shown.
1. 2. 3. 4.
5. 6. 7. 8.
ALDEK® Narrow Span Aluminum Scaffold Base Section Assembly Instructions
7.
Pre-level end frames by unlocking adjustable
leg assemblies and extending legs equally.
Place horizontal braces at the appropriate
level for use as guard rails by attaching frame locks to
end frame horizontals. Remove all people and material
from scaffold and final level using adjustable legs. Lock all
adjustable legs and read all instructions on scaffold and
scaffold platforms before use. Check Federal,State and Local
Codes regarding use of outriggers, toe boards, and guard rails
or consult manufacturer.

Pre-level end frame assembly by unlocking all
adjustable leg assemblies and extending legs equally. Lock
adjustable legs and run safety nut up snugly against locking
collar.
4.
3.
2.
1. Attach diagonal braces to upper and lower
end frame horizontals to form a vertical "x" as shown.
Lean end frame assembly against top of
stairway of erected base section so that the end frame with
the bottom of the stairway attached is facing out. Make sure
the curved portion of the stairway end is up. Using caution,
pull the upper section onto the base section platform.
Line up the upper section frame posts with those of
the base section.
Raise top of end frame to vertical position and
insert stacking pins into sockets at top of end frame vertical
post of base section. Position interlocking pins through holes
of end frame vertical posts and stacking pins.
7. Attach horizontal brace to vertical posts of
end frames just above the second from top horizontal with
the frame lock tube opening facing out. Place plywood
platform on top of platform support assembly. Line up pins
in tube with holes in plywood.
Attach frame locks of platform assembly to top
horizontal of end frame erected. Lift and rotate remaining
end frame to a vertical position, then insert stacking pins into
sockets as before. Position interlocking pins as in
previous step.
8.
5. 6.
ALDEK® Stairway Scaffold Base And Upper Section Assembly Instructions
Attach braces from outside outrigger posts
to end frame as shown.
Adjust outrigger leg to level outrigger frame.
Check that all frame locks are secure and for firm support
at all end frame and outrigger support points.
Attach frame locks of outrigger to vertical
post of base section as shown.
Push outrigger up vertical post of base
section until outrigger is against the top horizontal of
end frame as shown.
1.
Attach outrigger to vertical post of base
section with couplers as shown.
Adjust outrigger for maximum extension and
set diagonally out from corner post at angle to maximize
both length and width as shown.
1. Lock telescoping leg with interlocking pin.
Check for firm support at all end frame and outrigger
support points.
3.
ALDEK® Outrigger Attachment Instructions For Model FRO Rolling Outrigger
Place end frame assembly in open area so
that the end frame with the bottom of the stair way attached
is on top. Raise top end frame. Lock casters by depressing
foot brakes. Raise platform support assembly and attach to
top of end frame by engaging frame locks. Raise platform
frame assembly by grasping end frame horizontal member to
which upper portion of stair way is attached.
Place plywood platforms on platform support
assembly. Line up pins in tube with holes in plywood.
Remove all people and material and final level using adjustable
legs. Lock all adjustable legs and casters. Read and
understand all instructions on scaffold and scaffold platform
before use. Check Federal,State, and Local Codes regarding
use of outriggers, toe boards, and guard rails or
consult manufacturer.
2. 4.
3.
Outriggers may be required if more than the base section is used. (SEE ATTENTION BELOW!)
2.
ALDEK® Outrigger Attachment Instructions For Model OR-ADU
Adjustable Outrigger
Outriggers may be required if more than the base section is used. (SEE ATTENTION BELOW!)
Tower scaffold shown with FRO outriggers attached. Outriggers may be required to increase the maximum height of a tower. Maximum platform height is equal to 4x the smaller base section dimension
of the scaffold or installed outrigger in most states. Check Federal, State and Local Codes regarding use of outriggers.
ATTENTION

CORPORATE HEADQUARTERS
Werner Co.
93 Werner Road Greenville, PA 16125-9499
Tel. [phone]
FAX [phone]
www.wernerladder.com
C52 © 2002 Werner Co. Printed in U.S.A. January 2002
Snap Hook Frame lock
• Rugged design and easy to use
Aluminum Toe boards
• Added protection, increase strength and helps keep tools
from falling from scaffold
Outriggers
• Added stability and increases maximum height of the tower.
Standard and Non-Marring Casters
• Adjustable and lockable ( Non-marring casters should be
used in clean room environments )
Werner Scaffold Features Set The Standard For The Industry